. interrupt storm detected on "intr70:"; throttling interrupt source;
. Added access serialization on iicbus_transfer(), previously there was
no such protection and a new transfer could easily confuse the
controller;
. Add error checkings (i.e. stop the transfer when a error is detected
and do _not_ overwrite the previous error);
. On command done interrupt do not assume that the transfer was finished
sucessfully as we will receive the command done interrupt even after
errors;
. Simplify the FIFO handling;
. Reset the FIFO between the transfers as the FIFO may contain data from
the last (failed) transfer;
. Fix the iicbus speed for AM335x, which in turn will make better use of
the I2C noise filter (set to one internal clock cycle);
. Move the read and write handler to ithread instead of notifying the
requesting thread with wakeup(9);
. Fix the comments based on OMAP4 TRM.
The above changes allows me to read the EDID from my HDMI monitor on BBB
with gonzo's patches to support TDA19988 (which does 128 bytes reads) and
repeatedly scan the iicbus (with a modified i2c(8)) without lock up the bus.
Phabric: D465
header (Elf_Ehdr) to determine if a particular interpretor wants to
accept it or not. Use this mechanism to filter EABI arm on OABI arm
kernels, and vice versa. This method could also be used to implement
OABI on EABI arm kernels, if desired, or to allow a single mips kernel
to run o32, n32 and n64 binaries.
Differential Revision: https://reviews.freebsd.org/D609
soc-wide info lives. It was under dev.imx6_anatop.0.
What does anatop mean anyway? Nobody seems to know, so it's probably
not where somebody will think to look for imx6 hardware info.
configure the mux and config registers for PIO devices based on what
we find in the FDT. I developed it per the spec that had been
committed to Linux in the January 2014 time frame and haven't
updated. In short, bundles of pins are activated in specific ways for
specific configurations, and we implement all of that.
What's not included is a MI device infrastructure, any dynamic
run-time changing of these pins, etc. Also not included are hooks into
all the drivers to enable the latter (static at boot no driver changes
are needed). These larger questions will need to be answered once we
have more drivers like this for more platforms, or somebody has a heck
of a lot of time to research a bunch of platforms, the Linux solution
(which is good, but has its warts), etc.
work. This gets my AT91SAM9260-based boards almost booting with
current in multi pass. The MCI driver is broken, but it is equally
broken before multi-pass.
By Richard Earnshaw at ARM
>
>GCC has for a number of years provides a set of pre-defined macros for
>use with determining the ISA and features of the target during
>pre-processing. However, the design was always somewhat cumbersome in
>that each new architecture revision created a new define and then
>removed the previous one. This meant that it was necessary to keep
>updating the support code simply to recognise a new architecture being
>added.
>
>The ACLE specification (ARM C Language Extentions)
>(http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.set.swdev/index.html)
>provides a much more suitable interface and GCC has supported this
>since gcc-4.8.
>
>This patch makes use of the ACLE pre-defines to map to the internal
>feature definitions. To support older versions of GCC a compatibility
>header is provided that maps the traditional pre-defines onto the new
>ACLE ones.
Stop using __FreeBSD_ARCH_armv6__ and switch to __ARM_ARCH >= 6 in the
couple of places in tree. clang already implements ACLE. Add a define
that says we implement version 1.1, even though the implementation
isn't quite complete.
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
device attachment on arm platforms. If this is defined, nexus attaches
early in BUS_PASS_BUS, and other busses and devices attach later, in the
pass number they are set up for. Without it defined, nexus attaches in
BUS_PASS_DEFAULT and thus so does everything else, which is status quo.
Arm platforms which use FDT data to enumerate devices have been relying
on devices being attached in the exact order they're listed in the dts
source file. That's one of things currently preventing us from using
vendor-supplied fdt data (because then we don't control the order of the
devices in the data). Multi-pass attachment can go a long way towards
solving that problem by ensuring things like clock and interrupt drivers
are attached before the more mundane devices that need them.
The long-term goal is to have all arm fdt-based platforms using multipass.
This option is a bridge to that, letting us enable it selectively as
platforms are converted and tested (the alternative being to just throw
a big switch and try to fight fires as they're reported).
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
don't need any #ifdef stuff to use atomic_load/store_64() elsewhere in
the kernel. For armv4 the atomics are trivial to implement for kernel
code (just disable interrupts), less so for user mode, so this only has
the kernel mode implementations for now.
value shared across multiple cores is with atomic_load_64() and
atomic_store_64(), because the normal 64-bit load/store instructions
are not atomic on 32-bit arm. Luckily the ldrexd/strexd instructions
that are atomic are fairly cheap on armv6. Because it's fairly simple
to do, this implements all the ops for 64-bit, not just load/store.
Reviewed by: andrew, cognet
We have functions nested within functions, and places where we start a
function then never end it, we just jump to the middle of something else.
We tried to express this with nested ENTRY()/END() macros (which result
in .fnstart and .fnend directives), but it turns out there's no way to
express that nesting in ARM EHABI unwind info, and newer tools treat
multiple .fnstart directives without an intervening .fnend as an error.
These changes introduce two new macros, EENTRY() and EEND(). EENTRY()
creates a global label you can call/jump to just like ENTRY(), but it
doesn't emit a .fnstart. EEND() is a no-op that just documents the
conceptual endpoint that matches up with the same-named EENTRY().
This is based on patches submitted by Stepan Dyatkovskiy, but I made some
changes and added the EEND() stuff, so blame any problems on me.
Submitted by: Stepan Dyatkovskiy <stpworld@narod.ru>
