1) Properly detect the Symbol based cards (The 3Com Airconnect and their
ilk) and only reset them *ONCE* ever. This appears to make them work,
but more testing is needed. The tests that would wedge up my machine
completely now appear to work, but I have not real access points
handy.
2) Report both the Station firmware and the Primary firmware on Prism
based cards. On Lucent based cards, only report the station firmware
since that's all it supports. On symbol cards, report the symbol
specific firmware name as its station firmware.
3) Better Prism 2.5 and 3 family names. We really need to go table
driven for this.
4) Workaround for bugs in Intersil's firmware is only needed for at most
0.8.2 and earlier, since 0.8.3 and later appear to work.
Obtained from: NetBSD
stuff was right, but the busdma stuff was massively not right.
Didn't really test on ia64 or i386- don't have the former h/w and my
FreeBSD-current disk is unwell right now. Hope that this is okay.
MFC after: 1 week
"raw partition" of any kind since the floppy driver doesn't support
UFS-style partitions at all.
Reported by: "Crist J. Clark" <crist.clark@attbi.com>
Reviewed by: bde
MFC after: 3 days
date: 2001/08/15 00:04:59; author: augustss;
Add a little infrastructure so that individual drivers can easily check
if thee was a vendor+product locator match.
DIOCGMEDIASIZE instead.
The partition type check has been XXX'ed out since we cannot expect
that a BSD disklabel with a type field be available on all platforms.
revision 1.50
date: 2001/04/12 01:18:24; author: thorpej; state: Exp; lines: +6 -2
Only if __HAVE_GENERIC_SOFT_INTERRUPTS is then splusb == splsoftnet
(because we register the interrupt with IPL_SOFTNET). However, if
we're using a callout, then splusb == splsoftclock (because the
callouts happen from the softclock interrupt).
Note that splsoftnet blocks softclock interrupts, but this is
meant to better describe what's going on.
date: 2001/01/21 19:00:06; author: augustss;
Change the operation of the USB event thread. Before it only
performed USB device discovery, now it can also perform (short)
tasks for device drivers that need a process context, but don't
have one. This is not pretty, but better than using busy-wait
in an interrupt context.
o 3Com 3crwe62092a
o Addtron awp100
o No Wires Necessary WLAN 550 and 1148
o Proxim RANGELANDS 8340
and reorder linksys to be in proper sort order.
Obtained from: OpenBSD (mostly)
revision 1.138
date: 2001/10/02 17:59:38; author: pooka; state: Exp; lines: +6 -6
move DIAGNOSTIC-printf up one block to make it reachable
noted by Christophe Kalt in private email
(1.39), usbdi.c (1.79), usbdi.h (1.47), usbdivar.h (1.62)
date: 2001/01/21 02:39:52; author: augustss;
Add code to use soft interrupt to handle USB interrupt processing.
Don't enable the code since it doesn't work with the kludgy Ethernet
drivers.
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
revision 1.58
date: 2000/06/24 04:12:53; author: thorpej; state: Exp; lines: +5 -2
Kill SPLUSBCHECK -- it's not portable, and quite annoying on some
platforms which otherwise function just fine.
revision 1.127
date: 2000/11/22 05:50:59; author: soren; state: Exp; lines: +5 -5
In uhci_intr(), only warn about power state confusion if the
interrupt was actually for us.
date: 2000/08/08 19:51:46; author: tv; state: Exp; lines: +24 -13
%b -> bitmask_snprintf()
Because this code is shared, add a macro for bitmask_snprintf()
that should expand to the equivalent snprintf() on non-NetBSD
systems. This is only used in ?HCI_DEBUG cases anyway.
revision 1.81
date: 2000/10/24 15:01:26; author: augustss; lines: +36 -10
Add a hack to try and figure out if the TI UTUSB41 hub is bus
powered despite claiming to be self powered (it's important to
know so that the power budget can be met).
Part of this got merged in a previous commit, but not all.
revision 1.72
date: 2000/04/14 14:13:56; author: augustss; state: Exp; lines: +34 -27
Make attach of ugen work as it should so product&vendor locators
can be used.
usb.c 1.40:
revision 1.40
date: 2000/03/14 23:13:12; author: augustss; state: Exp; lines: +4 -1
Make sure the USB event thread discovers all devices first time
it call usb_discover(). It should now be possible to have the
root NFS mounted over a USB Ethernet Adapter.
----------------------------
revision 1.73
date: 2000/05/31 16:14:42; author: augustss; state: Exp; lines: +19 -6
Be more careful when setting the alternate interface so we don't
end up with nothing set at all if it fails.
----------------------------
----------------------------
revision 1.117
date: 2000/05/30 09:26:06; author: augustss; lines: +7 -1
As a safety, check that the controller is not suspended when we get
an interrupt.
----------------------------
ohci.c (1.85), ohcireg.h (1.17):
----------------------------
date: 2000/04/01 09:27:35; author: augustss;
Add a delay before reading the number of ports from the controller to
avoid getting 0 from it.
----------------------------
ohci.c (1.83), ohcireg.h (1.16), ohcivar.h (1.21)
===================================================================
date: 2000/03/29 01:46:26; author: augustss;
A first stab at support for isochronous transfers.
===================================================================
Caveats:
The new savecore program is not complete in the sense that it emulates
enough of the old savecores features to do the job, but implements none
of the options yet.
I would appreciate if a userland hacker could help me out getting savecore
to do what we want it to do from a users point of view, compression,
email-notification, space reservation etc etc. (send me email if
you are interested).
Currently, savecore will scan all devices marked as "swap" or "dump" in
/etc/fstab _or_ any devices specified on the command-line.
All architectures but i386 lack an implementation of dumpsys(), but
looking at the i386 version it should be trivial for anybody familiar
with the platform(s) to provide this function.
Documentation is quite sparse at this time, more to come.
Details:
ATA and SCSI drivers should work as the dump formatting code has been
removed. The IDA, TWE and AAC have not yet been converted.
Dumpon now opens the device and uses ioctl(DIOCGKERNELDUMP) to set
the device as dumpdev. To implement the "off" argument, /dev/null
is used as the device.
Savecore will fail if handed any options since they are not (yet)
implemented. All devices marked "dump" or "swap" in /etc/fstab
will be scanned and dumps found will be saved to diskfiles
named from the MD5 hash of the header record. The header record
is dumped in readable format in the .info file. The kernel
is not saved. Only complete dumps will be saved.
All maintainer rights for this code are disclaimed: feel free to
improve and extend.
Sponsored by: DARPA, NAI Labs
have ripped all the i386 specific formatting code from their
dump routines. Due to the potential for trashing disks, I did
not want to do this "blind".
(65536 * 32 - 1), but MAKEDEV only supports up to (32 * 32 -1). Device
names use the unit number in base 32 for all "digits".
This required fixing an old bug in MAKEDEV:ttyminor(). Its arg was the
global $unit instead of $1.
Reminded by: Valentin K. Ponomarenko <valka@krog.ukrtel.net>
MFC-after: 1 week
measured accurately for periodic interrupts provided the interrupts
don't need to be serviced very quickly to keep their period almost
constant. sio output interrupts have this property (interrupt service
can be delayed for up to 1 character time without the period changing).
This is non-optional and undocumented so that it can be added and
removed easily. It has no significant effect unless it is enabled by
hacking on a variable using a debugger. Hardclock and statclock interrupts
would work even better for this, at least on i386's, provided their
interrupt handlers are fast (as they are in -current but not in -stable
or in my version of -current).
allows us to properly parse cards with attribute memory based CIS that
before wouldn't parse correctly, sometimes with a panic. This allows
me to get my 3C562 modem/ethernet card to fail to attach due to
problems in the ep and sio drivers rather than due to problems in the
CIS parsing code :-).
We weren't setting the address to jump to for the function entries.
This caused us to only work when the addional entries were after the
first ones. On the 3C562/3C563 card this was not the case.
We were also mapping Attribute memory when common memory was asked for
in the target of the LONGLINK_{A,C} or LONGLINK_MFC.
My IBM Home And Away Modem/LAN card still fails for reasons unknown.
