discipline to do the async escaping, but no other benefits are available yet.
Change ``ifdef HAVE_DES'' to ``ifndef NODES'' for consistency.
Make the Makefile a little more sane WRT RELEASE_CRUNCH.
structures (well, they're treated as opaque).
It's now possible to manage IPv6 interface addresses and routing
table entries and to filter IPV6 traffic whether encapsulated or
not.
IPV6CP support is crude for now, and hasn't been tested against
any other implementations.
RADIUS and IPv6 are independent of eachother for now.
ppp.linkup/ppp.linkdown aren't currently used by IPV6CP
o Understand all protocols(5) in filter rules rather than only a select
few.
o Allow a mask specification for the ``delete'' command. It's now
possible to specifically delete one of two conflicting routes.
o When creating and deleting proxy arp entries, do it for all IPv4
interface addresses rather than doing it just for the ``current''
peer address.
o When iface-alias isn't in effect, don't blow away manually (via ``iface
add'') added interface addresses.
o When listening on a tcp server (diagnostic) socket, bind so that a
tcp46 socket is created -- allowing both IPv4 and IPv6 connections.
o When displaying ICMP traffic, don't display the icmp type twice.
When display traffic, display at least some information about unrecognised
traffic.
o Bump version
Inspired after filtering work by: Makoto MATSUSHITA <matusita@jp.FreeBSD.org>
options used to build ppp.
Currently, this is a no-op and only handles LOCALNAT and LOCALRAD cases.
This will be used for the upcoming ipv6 changes, and allows a shared
man page between OpenBSD and FreeBSD.
I don't claim to own the code and certainly don't want to discourage
people from fixing or updating it.
[I know it's the 29th, but the FREEZE hasn't yet been posted to committers]
going to remove ppp from the installation options in 5 days if ppp is
still broken, however, as it hasn't worked at installation time
for several weeks now and it's only causing people to fill my mailbox
with questions.
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.
Ppp controls the phone number, but idle timers and
SYNC/RAW decisions are still made by isdnd (in isdnd.rc).
This involves a new datalink state machine phase. The
``wait for carrier'' phase happens after dialing but
before logging in. The whole dial state should really
be abstracted so that each device type can deal with it
in its own way (thinking about PPPoE) - but that'll have
to wait.
The ``set cd'' symantics remain the same for tty devices,
but we now delay until we either get CD or timeout waiting
(at which time we drop the link if we require CD).
For i4b devices we always insist on carrier.
Thanks to hm@ for his help, and especially for pointing out
that I *don't* need to re-implement isdnd (that was a huge
waste of time !) :-]
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.
A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.
This proves that PPPoE is plausable in userland....
This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !
iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.
The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').
Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.
Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.
Assign our physical device name for incoming tcp connections by
calling getpeername().
Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().
the layering.
We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.
Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.
o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.
details. Compiling with -DNORADIUS (the default for `release')
removes support.
TODO: The functionality in libradius::rad_send_request() needs
to be supplied as a set of routines so that ppp doesn't
have to wait indefinitely for the radius server(s). Instead,
we need to get a descriptor back, select() on the descriptor,
and ask libradius to service it when necessary.
For now, ppp blocks SIGALRM while in rad_send_request(), so
it misses PAP/CHAP retries & timeouts if they occur.
Only PAP is functional. When CHAP is attempted, libradius
complains that no User-Password has been specified... rfc2138
says that it *mustn't* be used for CHAP :-(
Sponsored by: Internet Business Solutions Ltd., Switzerland
