Oh, I forgot to mention: this driver also works on FreeBSD/alpha (big
thanks to Andrew Gallatin). And there is a 2.2.x version available for
those who stubbornly refuse to upgrade.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
Like the PNIC, we have to copy packet headers in the receive handler
because the chip will only DMA to longword aligned buffers.
Also do some mindor cleanups.
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
- When trying to map ports, if mapping TL_PCI_LOIO or TL_PCI_LOMEM fails,
try mapping the other one. Apparently, some ThunderLAN parts swap these
two registers while others don't.
- Add support for bitrate (non-MII) PHYs. If no MII-based PHY is found,
program the chip for bitrate mode. This is required for the TNETE110
part, which doesn't have MII support. (It's also obsolete, but there
are still some people out there who have them.) With this change and the
change above, the Compaq Netflex-3/P 10baseT/BNC board works correctly.
(Thanks to Matthew Dodd for getting me one of these cards.)
- Convert to bus_space_foo() for register accesses.
- Add changes to support FreeBSD/Alpha. I still have to actually test
this in my Alpha box so I'm not going to update /sys/alpha/conf/GENERIC
yet.
Contributed-by: "Richard Seaman, Jr." <dick@tar.com>
Tested-by: Chris Piazza <cpiazza@home.net>
Tugrul Galatali <tugrul@ianai.BlackSun.org>
grog
This code includes lots of stuff for verbose probing. I'm not 100%
sure that the output of the verbose probe is correct, but everything
else works fine, and -CURRENT was broken for the 5591 before, so I'm
committing it anyway.
sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
Recognize aic7895 controllers that have been "acquired" by a RAIDPort
card as normal aic7895s.
Recognize the aic7815 Raid Parity/Memory controller chip and notify
the user that it's RAID functionality will be ignored.
gave yet another internal register layout model for what is
*still* the same architecture. I hope they saved billyuns of gates
'coz otherwise this is *really* annoying.
chip int. and ext. clock synchronisation). Fixed workaround for
transmit threshold underrun. Added volatile keyword to CSR_READ_* and
CSR_WRITE_* macroses. Added DELAYs to eliminate randomness caused
by processor speed. Fixed all TXCON and RXCON registers to be accessed
only when chip is idle, as manual told. Changed epic_init_phy to
drop link by isolating and going loopback, should should force link
partner to restart autonegotiation.
PR: kern/10535, kern/9742, kern/10575
Submitted by: Peter Jeremy, David Greenman
a wierd double-queue arrangement.. It always empties the if_snd queue
then puts the transmit packets into a different queue that is limited
by the number of TX descriptors and does it's own discards...
This should stop the boot-time XXX warning anyway.
The i++ loop from 1..1000 is too small on very fast machines like
PII 450 MHz. Increasing the loop from 1..100000 lets the machine
access PHY. After this patch it's possible to use a SMC PCI card
on a HP Kayak XA series PC Workstation. Workaround until this fix
was to enable debugging in the driver (#define EPIC_DEBUG 1).
Without that patch you get an undefined state:
while true
do
ifconfig -a | grep status:
done
The status messages flaps between twwo values, but not
"connected".
Obtained from: Ustimenko Semen <semen@iclub.nsu.ru>
tulip_addr_filter() on SIOCSIFFLAGS, and was nuking the IFF_ALLMULTI
on entering tulip_addr_filter(). As a result it was impossible to run
a multicast router on a machine with a "de" interface.
Added autodetection of MMAC Osprey 100 card for
Jan Schmidt <mmedia@rz.uni-greifswald.de>. The MMAC card has an EEPROM
which contains an ASCII string beginning with "MMAC".
Corrected Hauppauge Audio Mux Mute value from 0x01 to 0x04.
Fixed a typo.
Sumitted change:
Added ALPS Tuner Type submitted by Hiroki Mori <mori@infocity.co.jp>
Submitted by: Roger Hardiman and Hiroki Mori <mori@infocity.co.jp>
Addtron appear to have their own VIA Rhine II and RealTek 8139 boards
with custom PCI vendor and device IDs. This commit updates the PCI
vendor and device lists in the vr and rl drivers so that we can probe
the additional devices.
Found by: nosing around the PCI vendor and device code list at:
http://www.halcyon.com/scripts/jboemler/pci/pcicode
AX88140A with power management and magic packet support. Correct the
addresses of the PCI power management registers and add some code to
detect the revision ID of the AX88141 and identify it in the probe
messages.
No other changes are needed since the AX88141 is functionally
identical to the AX88140A.
Now should be able to report speed for cards using NatSemi PHY.
(if you have one please let me know if it works as I
only have the Intel version)
Reviewed by: David Greenman <dg@root.com>
3c905B, the RX and TX reset commands also reset the cyclone chip's internal
PHY, which causes it to restart its autonegotiation session. This takes a
second or two to complete, which makes the interface seem to stop responding
for a few seconds every time you do something that reinitializes it.
Issuing the RX and TX resets on the older 3c905 boomerang adapters doesn't
cause any delay because the boomerang chip requires an external PHY.
This should fix the problem where people doing network installs via 3c905B
cards experience a delay after the interface is first initialized, among
other things.
Submitted by Roger Hardiman.
Added ioctl TVTUNER_GETCHANSET to discover which regions the bktr driver
supports. Submitted by Vsevolod Lobko <seva@alex-ua.com>
Added BT848_GPIO_SET_EN,BT848_GPIO_SET_DATA (and GETs) to allow user land
control of the GPIO pins. This allows a Radio module on the GPIO port
to be controlled. Submitted by Vsevolod Lobko <seva@alex-ua.com>
The kernel option BKTR_GPIO_ACCESS must be used to enable the GPIO ioctls.
Submitted by: Roger Hardiman and Vsevolod Lobko <seva@alex-ua.com>
Improved MSP34xx reset for bt848 Hauppauge boards.
Added detection for Bt848a.
Vsevolod Lobko<seva@sevasoft.alex-ua.com> added more XUSSR channels.
Submitted by: parts from Vsevolod Lobko<seva@sevasoft.alex-ua.com>
Obtained from: parts from OpenBSD
