netback.c: Add missing VM includes.
xen/xenvar.h,
xen/xenpmap.h: Move some XENHVM macros from <machine/xen/xenpmap.h> to
<machine/xen/xenvar.h> on i386 to match the amd64 headers.
conf/files: Add netback to the build.
Submitted by: jhb
MFC after: 3 days
The cs driver requires a table with firmware values. An
alternative firmware is available in a similar Open Sound
System driver. This is actually a partial revert of
Revision 77504.
Special thanks to joel@ for patiently testing several
replacement attempts.
The csa driver and the complete sound system are now free
of the GPL.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
channels available
- current code treats bits 4:7 in 'SATAHC interrupt mask' and 'SATAHC
interrupt cause' as flags for SATA channels 2 and 3
- for embedded SATA controllers (SoC) these bits have been marked as reserved
in datasheets so far, but for some new and upcoming chips they are used for
purposes other than SATA
Submitted by: Lukasz Plachno
Reviewed by: mav
Obtained from: Semihalf
MFC after: 2 weeks
* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.
* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.
The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.
Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.
hardware imposes strict limitations on hard buffer and block sizes.
Previous code set soft buffer to be no smaller then hard buffer. On some
cards with fixed 64K physical buffer that caused up to 800ms play latency.
New code allows to set soft buffer size down to just two blocks of the hard
buffer and to not write more then that size ahead to the hardware buffer.
As result of that change I was able to reduce full practically measured
record-playback loop delay in those conditions down to only about 115ms
with theoretical playback latency of only about 50ms.
New code works fine for both vchans and direct cases. In both cases sound(4)
tries to follow hw.snd.latency_profile and hw.snd.latency values and
application-requested buffer and block sizes as much as limitation of two
hardware blocks allows.
Reviewed by: silence on multimedia@
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
* For legacy NICs, the combined RSSI should be used.
For earlier AR5416 NICs, use control chain 0 RSSI rather than combined
RSSI.
For AR5416 > version 2.1, use the combined RSSI again.
* Add in a missing AR5212 HAL method (get11nextbusy) which may be called
by radar code.
This serves no functional change for what's currently in FreeBSD.
* Grab the net80211com lock when calling ieee80211_dfs_notify_radar().
* Use the tsf extend function to turn the 64 bit base TSF into a per-
frame 64 bit TSF. This will improve radiotap logging (which will
now have a (more) correct per-frame TSF, rather then the single TSF64
value read at the beginning of ath_rx_proc().
primitives by breaking stop_scheduler into a per-thread variable.
Also, store the new td_stopsched very close to td_*locks members as
they will be accessed mostly in the same codepaths as td_stopsched and
this results in avoiding a further cache-line pollution, possibly.
STOP_SCHEDULER() was pondered to use a new 'thread' argument, in order to
take advantage of already cached curthread, but in the end there should
not really be a performance benefit, while introducing a KPI breakage.
In collabouration with: flo
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
cards powering up at once. Work around the easy case (multiple cards
inserted on boot) with a short sleep and a long comment. This
improves reliability on those laptops with power hungry cards.
cleared/dropped leading to qid2tap[n] being NULL as there no longer
is a tap. Now, if there have been lots of frames queued the firmware
processes and returns those after the tap is gone.
Tested by: osa
MFC after: 1 week
Remove unneeded temporary variable (data) to better match the OSS code.
Remove some unused constants and type definitions.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
This involves significant changes to the mps(4) driver, but is not a
complete rewrite.
Some of the changes in this version of the driver:
- Integrated RAID (IR) support.
- Support for WarpDrive controllers.
- Support for SCSI protection information (EEDP).
- Support for TLR (Transport Level Retries), needed for tape drives.
- Improved error recovery code.
- ioctl interface compatible with LSI utilities.
mps.4: Update the mps(4) driver man page somewhat for the driver
changes. The list of supported hardware still needs to be
updated to reflect the full list of supported cards.
conf/files: Add the new driver files.
mps/mpi/*: Updated version of the MPI header files, with a BSD style
copyright.
mps/*: See above for a description of the new driver features.
modules/mps/Makefile:
Add the new mps(4) driver files.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: ken
MFC after: 1 week
share/man/man4/Makefile,
share/man/man4/xnb.4,
sys/dev/xen/netback/netback.c,
sys/dev/xen/netback/netback_unit_tests.c:
Rewrote the netback driver for xen to attach properly via newbus
and work properly in both HVM and PVM mode (only HVM is tested).
Works with the in-tree FreeBSD netfront driver or the Windows
netfront driver from SuSE. Has not been extensively tested with
a Linux netfront driver. Does not implement LRO, TSO, or
polling. Includes unit tests that may be run through sysctl
after compiling with XNB_DEBUG defined.
sys/dev/xen/blkback/blkback.c,
sys/xen/interface/io/netif.h:
Comment elaboration.
sys/kern/uipc_mbuf.c:
Fix page fault in kernel mode when calling m_print() on a
null mbuf. Since m_print() is only used for debugging, there
are no performance concerns for extra error checking code.
sys/kern/subr_scanf.c:
Add the "hh" and "ll" width specifiers from C99 to scanf().
A few callers were already using "ll" even though scanf()
was handling it as "l".
Submitted by: Alan Somers <alans@spectralogic.com>
Submitted by: John Suykerbuyk <johns@spectralogic.com>
Sponsored by: Spectra Logic
MFC after: 1 week
Reviewed by: ken
- add "+HP" in case of headphones redirection;
- add device type for analog devices, if all pins have the same.
As result now it may look like "Analog 5.1+HP/2.0" or "Front Analog Mic".
I hope it will be more useful than long and confusing.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
- remove experimental code for disabling CRC
- use the correct constant for conversion between interrupt rate
and EITR values (the previous values were off by a factor of 2)
- make dev.ix.N.queueM.interrupt_rate a RW sysctl variable.
Changing individual values affects the queue immediately,
and propagates to all interfaces at the next reinit.
- add dev.ix.N.queueM.irqs rdonly sysctl, to export the actual
interrupt counts
Netmap-related changes for ixgbe:
- use the "new" format for TX descriptors in netmap mode.
- pass interrupt mitigation delays to the user process doing poll()
on a netmap file descriptor.
On the RX side this means we will not check the ring more than once
per interrupt. This gives the process a chance to sleep and process
packets in larger batches, thus reducing CPU usage.
On the TX side we take this even further: completed transmissions are
reclaimed every half ring even if the NIC interrupts more often.
This saves even more CPU without any additional tx delays.
Generic Netmap-related changes:
- align the netmap_kring to cache lines so that there is no false sharing
(possibly useful for multiqueue NICs and MSIX interrupts, which are
handled by different cores). It's a minor improvement but it does not
cost anything.
Reviewed by: Jack Vogel
Approved by: Jack Vogel
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
(HDMI and HBR bits set) and needed (AC3 format used with 8 channels).
This should allow DTS-HD/TrueHD pass-through with rates above 6.144Mbps.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
widgets. I am not sure if S/PDIF supports 32bit samples, but my Marantz
SR4001 doesn't, producing only single clicks on playback start/stop.
Because HDA controller requires 32bit alignment for all samples above 16bit,
we can't handle this situation in regular way and have to set 32bit format
in sound(4) for anything above 16bit. To workaround the problem, prefer
to setup hardware to use 24/20bit samples when 32bit format requested. Add
dev.pcm.X.play.32bit and dev.pcm.X.rec.32bit sysctls to control what format
really use for 32bit samples.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
maximal from 64K to 256K.
We usually don't need 750 sound interrupts per second (1.3ms latency)
when playing 192K/24/8 stream. 187 should be better. On usual 48K/16/2
it is just enough for hw.snd.latency=9 at hw.snd.latency_profile=1 with
23 and 6 interrupts per second.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
