such as j:name:maxproc:sigkill=100. Proper fix - deferring psignal
to a taskqueue - is somewhat complicated and thus will happen
after 9.0.
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
flags field. Updates to the atomic flags are performed using the atomic
ops on the containing word, do not require any vm lock to be held, and
are non-blocking. The vm_page_aflag_set(9) and vm_page_aflag_clear(9)
functions are provided to modify afalgs.
Document the changes to flags field to only require the page lock.
Introduce vm_page_reference(9) function to provide a stable KPI and
KBI for filesystems like tmpfs and zfs which need to mark a page as
referenced.
Reviewed by: alc, attilio
Tested by: marius, flo (sparc64); andreast (powerpc, powerpc64)
Approved by: re (bz)
The current code was rounding down the maximum frame size instead of
routing up, resulting in a read size of 1024 bytes, in the non-jumbo
frame case, and splitting the packets across multiple mbufs.
Consequently the above problem exposed another issue, which is when
packets were splitted across multiple mbufs, and all of the mbufs in the
chain have the M_PKTHDR flag set.
Submitted by: original patch by Ray Ruvinskiy at BlueCoat dot com
Reviewed by: jfv, kmacy, rwatson
Approved by: re (rwatson)
MFC after: 5 days
is retrieved after a failed SCSI command to continue normal
operation. Else this sense information is retrived at the next
SCSI command.
Approved by: re (kib)
Reported by: Alex Kozlov
MFC after: 1 week
PR: usb/160299
* Update the hardware access register definitions and functions to bring
them in line with other Netlogic software.
* Update the platform bus to use PCI even for on-chip devices. Add a dummy
PCI driver to ignore on-chip devices which do not need driver.
* Provide memory and IRQ resource allocation code for on-chip devices
which cannot get it from PCI config.
* add support for on-chip PCI and USB interfaces.
* update conf files, enable pci and retain old MAXCPU until we can support
>32 cpus.
Approved by: re(kib), jmallett
hostid, this gives a good chance of keeping the same address over
reboots. This is intended to help IPV6 and similar which generate
their addresses from the mac.
PR: kern/160300
Submitted by: mdodd
Approved by: re (kib)
While this is generally good, it brings along a serie of problems,
like clocks going off sync and in presence of SW_WATCHDOG, watchdogs
firing without a good reason (missed hardclock wdog ticks update).
Fix the latter by kicking the watchdog just before to re-enable the interrupts.
Also, while here, not rely on users to stop the watchdog manually when
entering DDB but do that when entering KDB context.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, rstone
Approved by: re (kib)
MFC after: 1 week
which requires that ni_strictrelative be set to 0, post-r224810.
Tested by: swills (earlier version), geo dot liaskos at gmail.com
Approved by: re (kib)
pre-r222417 state. The behavior was essentially reversed in r222417
which can cause confusion.
PR: 159775
Submitted by: Devin Teske
Approved by: re (kib)
which does not support the no synchronize cache SCSI command.
The __FreeBSD_version version macro has been bumped and
external kernel modules needs to be recompiled after
this patch.
Approved by: re (kib)
MFC after: 1 week
PR: usb/160299
and the new setmode and setowner fileops in FreeBSD 9.0:
- Add new MAC Framework entry point mac_posixshm_check_create() to allow
MAC policies to authorise shared memory use. Provide a stub policy and
test policy templates.
- Add missing Biba and MLS implementations of mac_posixshm_check_setmode()
and mac_posixshm_check_setowner().
- Add 'accmode' argument to mac_posixshm_check_open() -- unlike the
mac_posixsem_check_open() entry point it was modeled on, the access mode
is required as shared memory access can be read-only as well as writable;
this isn't true of POSIX semaphores.
- Implement full range of POSIX shared memory entry points for Biba and MLS.
Sponsored by: Google Inc.
Obtained from: TrustedBSD Project
Approved by: re (kib)
- tjmax - Tj(max) value from the CPU
- delta - current delta reading
- resolution - sensor resolution in Celsius
- throttle_log - whether a #PROCHOT was asserted since last reset
Submitted by: Mark Johnston <markjdb gmail.com> (mostly)
MFC after: 1 month
Approved by: re (kib)
been interrupted in a restartable syscall. Otherwise we could end up
in an (almost) endless loop in clnt_reconnect_call().
PR: kern/160198
Reviewed by: rmacklem
Approved by: re (kib), avg (mentor)
MFC after: 1 week
which may cause problems when these contain garbage so zero the range
descriptors embedding the rmans when allocating them.
Approved by: re (kib)
MFC after: 3 days
route with the same prefix is searched for as a replacement. The
current code did not bypass routes that have non-operational
interfaces. This patch fixes that bug and will find a replacement
route with an active interface.
PR: kern/159603
Submitted by: pluknet, ambrisko at ambrisko dot com
Reviewed by: discussed on net@
Approved by: re (bz)
MFC after: 3 days
keyboards allow console break sequences (such as ctrl-alt-esc) to be
entered, alternative break can prove useful under virtualisation and
remote console systems where entering control sequences can be
difficult or unreliable.
MFC after: 3 weeks
Approved by: re (bz)
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
accessible:
(1) Always compile in support for breaking into the debugger if options
KDB is present in the kernel.
(2) Disable both by default, but allow them to be enabled via tunables
and sysctls debug.kdb.break_to_debugger and
debug.kdb.alt_break_to_debugger.
(3) options BREAK_TO_DEBUGGER and options ALT_BREAK_TO_DEBUGGER continue
to behave as before -- only now instead of compiling in
break-to-debugger support, they change the default values of the
above sysctls to enable those features by default. Current kernel
configurations should, therefore, continue to behave as expected.
(4) Migrate alternative break-to-debugger state machine logic out of
individual device drivers into centralised KDB code. This has a
number of upsides, but also one downside: it's now tricky to release
sio spin locks when entering the debugger, so we don't. However,
similar logic does not exist in other device drivers, including uart.
(5) dcons requires some special handling; unlike other console types, it
allows overriding KDB's own debugger selection, so we need a new
interface to KDB to allow that to work.
GENERIC kernels in -CURRENT will now support break-to-debugger as long as
appropriate boot/run-time options are set, which should improve the
debuggability of BETA kernels significantly.
MFC after: 3 weeks
Reviewed by: kib, nwhitehorn
Approved by: re (bz)
devices supported by puc(4) to work "out of the box" since puc.ko does
not work "out of the box".
Reviewed by: marcel
Approved by: re (kib)
MFC after: 1 week
but not removed; decrement it instead when the child jail actually
goes away. This avoids letting the counter go below zero in the case
where dying (pr_uref==0) jails are "resurrected", and an associated
KASSERT panic.
Submitted by: Steven Hartland
Approved by: re (bz)
MFC after: 1 week
If a selinfo object is recorded (via selrecord()) and then it is
quickly destroyed, with the waiters missing the opportunity to awake,
at the next iteration they will find the selinfo object destroyed,
causing a PF#.
That happens because the selinfo interface has no way to drain the
waiters before to destroy the registered selinfo object. Also this
race is quite rare to get in practice, because it would require a
selrecord(), a poll request by another thread and a quick destruction
of the selrecord()'ed selinfo object.
Fix this by adding the seldrain() routine which should be called
before to destroy the selinfo objects (in order to avoid such case),
and fix the present cases where it might have already been called.
Sometimes, the context is safe enough to prevent this type of race,
like it happens in device drivers which installs selinfo objects on
poll callbacks. There, the destruction of the selinfo object happens
at driver detach time, when all the filedescriptors should be already
closed, thus there cannot be a race.
For this case, mfi(4) device driver can be set as an example, as it
implements a full correct logic for preventing this from happening.
Sponsored by: Sandvine Incorporated
Reported by: rstone
Tested by: pluknet
Reviewed by: jhb, kib
Approved by: re (bz)
MFC after: 3 weeks
and the maximum TCP send and receive buffer limits from 256kB
to 2MB.
For sb_max_adj we need to add the cast as already used in the sysctl
handler to not overflow the type doing the maths.
Note that this is just the defaults. They will allow more memory
to be consumed per socket/connection if needed but not change the
default "idle" memory consumption. All values are still tunable
by sysctls.
Suggested by: gnn
Discussed on: arch (Mar and Aug 2011)
MFC after: 3 weeks
Approved by: re (kib)
Remove mapped pages for all dataset vnodes in zfs_rezget() using
new vn_pages_remove() to fix mmapped files changed by
zfs rollback or zfs receive -F.
PR: kern/160035, kern/156933
Reviewed by: kib, pjd
Approved by: re (kib)
MFC after: 1 week
to find the first route node of an ECMP chain before executing the route
command. If the system has a default route, and the specific route argument
to the command does not exist in the routing table, then the default route
would be reached. The current code does not verify the reached node matches
the given route argument, therefore erroneous removed the entry. This patch
fixes that bug.
Approved by: re
MFC after: 3 days
The AR5212 HAL didn't check this field; timers are enabled a different
way.
The AR5416 HAL however did, and since this field was uninitialised, it had
whatever was on the stack at the time. This lead to "unpredictable"
behaviour.
This allows TDMA to work on the AR5416 and later chipsets.
Thanks to: paradyse@gmail.com
Approved by: re (kib, blanket)
didn't set a sequence number; it didn't show up earlier because the
hardware most people use for hostap (ie, AR5212 series stuff) sets the
sequence numbers up in hardware. Later hardware (AR5416, etc) which
can do 11n and aggregation require sequence numbers to be generated in
software.
Submitted by: paradyse@gmail.com
Approved by: re (kib)
* Fix SLEEP1/SLEEP2 register definitions; the CAB/Beacon timeout
fields have changed in AR5416 and later
* The TIM_PERIOD and DTIM_PERIOD registers are now microsecond fields,
not TU.
Obtained from: Linux ath9k, Atheros reference
Approved by: re (kib, blanket)
default/loader.conf
This should help people installing ${OS} to USB devices, where there are
frequently cases where kernel tries to mount root before actual umass sensing
is finished.
Reviewed by: mav
Approved by: re (kib)
MFC after: 1 week
or later. Previous hardware had some as TU, some as 1/8th
TU.
* Modify AR_NEXT_DBA and AR_NEXT_SWBA to use a new macro,
ONE_EIGHTH_TU_TO_USEC(), which converts the 1/8th TU
fields to USEC. This is just cosmetic and matches the
Atheros reference driver.
* Fix AR_NEXT_TBTT, which is USEC, not TU.
Submitted by: paradyse@gmail.com
Approved by: re (kib, blanket)
mld_set_version() is called only from mld_v1_input_query() and
mld_v2_input_query() both holding the if_addr_mtx lock, and then calling
into mld_v2_cancel_link_timers() acquires it the second time, which results
in mtx recursion. To avoid that, delay if_addr_mtx acquisition until after
mld_set_version() is called; while here, further reduce locking scope
to protect only the needed pieces: if_multiaddrs, in6m_lookup_locked().
PR: kern/158426
Reported by: Thomas <tps vr-web.de>,
Tom Vijlbrief <tom.vijlbrief xs4all.nl>
Tested by: Tom Vijlbrief
Reviewed by: bz
Approved by: re (kib)
programming secret. The PHY would go into sleep state when it
detects no established link and it will re-establish link when the
cable is plugged in. Previously it failed to re-establish link
when the cable is plugged in such that it required to manually down
and up the interface again to make it work. This came from
incorrectly programmed hibernation parameters. According to
Atheros, each PHY chip requires different configuration for
hibernation and different vendor has different settings for the
same chip.
Disabling hibernation may consume more power but establishing link
looks more important than saving power.
Special thanks to Atheros for giving me instructions that disable
hibernation.
MFC after: 1 week
Approved by: re (kib)
that allow a module to use an order other than the default of
SI_ORDER_MIDDLE when registering a driver. This can be useful for drivers
in a kld that contain multiple new-bus drivers as part of one logical device
driver. A typical case would be to use SI_ORDER_LAST for the "main" driver
to ensure that any other "helper" drivers are registered and available
before the "main" driver attempts to attach.
Tested by: kib, Jason Harmening jason harmening / gmail
Approved by: re (kib)
MFC after: 1 week
