I had a reason for doing this, but it violates the principle of least
astonishment. (At some point I may put this back but attach it to one of
the LINK flags so the behavior can be toggled on and off.)
Also replace my tl_calchash() with a much less disgusting and substantially
smaller one supplied by Bill Fenner.
These are probably generated by other PCI devices sharing the TLAN's
interrupt. The programmer's guide says to simply re-enable interrupts
and return if one of these is detected.
Prompted by bug report from: Bill Fenner
in -current is over, I'll put a 2.2.x specific version in the RELENG_2_2
branch. If somebody wants a 2.2 version of this driver now, they can check
out the previous version from CVS or ask me via e-mail.
Gee people, I didn't mean to stir up such a controversy. I just wanted
to make sure I could get this thing to work with both kernel versions
and didn't want to have to maintain two separate copies. All ya hadda
do was ask. :)
drivers here do and it also blows up in building GENERIC during
a release build if you try and include <osreldate.h> (which shot
my SNAP dead - argh!). Use __FreeBSD__ instead.
This driver supports the following cards/integrated ethernet controllers:
Compaq Netelligent 10, Compaq Netelligent 10/100, Compaq Netelligent 10/100,
Compaq Netelligent 10/100 Proliant, Compaq Netelligent 10/100 Dual Port,
Compaq NetFlex-3/P Integrated, Compaq NetFlex-3/P Integrated,
Compaq NetFlex 3/P w/ BNC, Compaq Deskpro 4000 5233MMX.
It should also support Texas Instruments NICs that use the ThunderLAN
chip, though I don't have any to test. If you've got a card that uses
the ThunderLAN chip but isn't listed in the PCI vendor/product list in
if_tl.c, try adding it and see what happens.
The driver supports any MII compliant PHY at 10 or 100Mbps speeds in
full or half duplex. (Those I've personally tested are the National
Semiconductor DP83840A (Prosignia server), the Level 1 LXT970 (Deskpro
desktop), and the ThunderLAN's internal 10baseT PHY.) Autonegotiation,
hardware multicast filtering, BPF and ifmedia support are included.
This chip is pretty fast; Prosignia servers with NCR SCSI, ThunderLAN
ethernet and FreeBSD make for a nice combination.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
in the kernel config file makes the driver's video_open() function
select PAL rather than NTSC. This fixed all the hangs on my
Dual Crystal card when using a PAL video signal.
As a result, you can loose the tsleep (of 2 seconds - now 0.25!!)
which I previously added. (Unless someone else wanted the 0.25
second tsleep).
submitted ioctl to clear the video buffer
prior to starting video capture
Amancio : clean up yuv12 so that it does not
affect rgb capture. Basically, fxtv after
capturing in yuv12 mode , switching to rgb
would cause the video capture to be too bright.
1.32 disable inverse gamma function for rgb and yuv
capture. fixed meteor brightness ioctl it now
converts the brightness value from unsigned to
signed.
1.33 added sysctl: hw.bt848.tuner, hw.bt848.reverse_mute,
hw.bt848.card
card takes a value from 0 to bt848_max_card
tuner takes a value from 0 to bt848_max_tuner
reverse_mute : 0 no effect, 1 reverse tuner
mute function some tuners are wired reversed :(
as variables declared in the main block in the function, so shadowing
of parameters by variables declared in the main block is not just an
obfuscation).
Found by: lint
Technologies' Socket 7 chipsets. This covers all of the Apollo chipsets
except the Master (82C570) and the MVP3, and it also covers the cheap
VXPro and VXTWO knockoffs of the VP1 and VPX.
PR: 6481
Reviewed by: phk
Submitted by: Lee Cremeans <lcremean@tidalwave.net>
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Roger Hardiman <roger@cs.strath.ac.uk> :
Revised autodetection code to correctly handle both
old and new VideoLogic Captivator PCI cards.
Added tsleep of 2 seconds to initialistion code for PAL users.
Corrected clock selection code on format change.
--- Amancio
- Attempt to handle PCI devices where the interrupt is
an ISA/EISA interrupt according to the mp table.
- Attempt to handle multiple IO APIC pins connected to
the same PCI or ISA/EISA interrupt source. Print a
warning if this happens, since performance is suboptimal.
This workaround is only used for PCI devices.
With these two workarounds, the -SMP kernel is capable of running on
my Asus P/I-P65UP5 motherboard when version 1.4 of the MP table is disabled.
"time" wasn't a atomic variable, so splfoo() protection were needed
around any access to it, unless you just wanted the seconds part.
Most uses of time.tv_sec now uses the new variable time_second instead.
gettime() changed to getmicrotime(0.
Remove a couple of unneeded splfoo() protections, the new getmicrotime()
is atomic, (until Bruce sets a breakpoint in it).
A couple of places needed random data, so use read_random() instead
of mucking about with time which isn't random.
Add a new nfs_curusec() function.
Mark a couple of bogosities involving the now disappeard time variable.
Update ffs_update() to avoid the weird "== &time" checks, by fixing the
one remaining call that passwd &time as args.
Change profiling in ncr.c to use ticks instead of time. Resolution is
the same.
Add new function "tvtohz()" to avoid the bogus "splfoo(), add time, call
hzto() which subtracts time" sequences.
Reviewed by: bde
Fixed pedantic semantics errors (in ANSI C, static arrays must have
a size, and static objects should be consistently declared as static
unless you know more than anyone should have to know about the
linkage rules).
