I've seen this fail from time to time and just hang during reset.
Instead of it just hanging, just poke it again. I've not seen it
fail in hundreds of test resets now.
Tested:
* AR9344 AP/STA configuration
Move dump_avail[] extern declaration and inlines into a new header
vm/vm_dumpset.h. This fixes default gcc build for mips.
Reviewed by: alc, scottph
Tested by: kevans (previous version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D26741
The AR9341 AHB runs at 225MHz, much faster than the 33MHz of the
AR71xx AHB. So not only is the math going to do weird things, it
will also wrap rather than being clamped.
So:
* clamp! don't wrap!
* tidy up some debugging
* add an option to throw an NMI rather than reset!
Tested:
* AR9341 SoC (TP-Link TL-WDR4300), patting/not patting the watchdog!
Match other architectures and print CPU information during
cpu_startup(). In particular, this prints the information after the
message buffer is initialized which allows it to be retrieved after
boot via dmesg(8).
While here, add some extern declarations to <machine/md_var.h> in
place of duplicated declarations in various source files.
Reviewed by: brooks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24936
This is stuff I've been running for a couple years. It's inspired by changes
I found in the linux ag71xx ethernet driver.
* Delay between stopping DMA and checking to see if it's stopped; this gives
the hardware time to do its thing.
* Non-final frames in the chain need to be a multiple of 4 bytes in size.
Ensure this is the case when assembling a TX DMA list.
* Add counters for tx/rx underflow and too-short packets.
* Log if TX/RX DMA couldn't be stopped when resetting the MAC.
* Add some more debugging / logging around TX/RX ring bits.
Tested:
* AR7240, AR7241
* AR9344 (TL-WDR3600/TL-WDR4300 APs)
* AR9331 (Carambola 2)
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
doing so adds more flexibility with less redundant code.
Reviewed by: jhb, markj, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D21250
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
This is reqired to use the gpiofunc behaviour for configuring GPIO
pins at boot time.
Submitted by: <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D20170
AR724X_GPIO_PINS used for this family is defined as 18
The datasheet for the AR7241 describes 20 pins, allow all to be used.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka
Differential Revision: https://reviews.freebsd.org/D17580
This is an amalgam of a patch by Doug Ambrisko to
generalize uart_acpi_find_device, imp moving the
ACPI table to uart_dev_ns8250.c and advice by jhb
to work around a bug in the EPYC 3151 BIOS
(the BIOS incorrectly marks the serial ports as
disabled)
Reviewed by: imp
MFC after: 8 weeks
Differential Revision: https://reviews.freebsd.org/D16432
pmc_process_interrupt takes 5 arguments when only 3 are needed.
cpu is always available in curcpu and inuserspace can always be
derived from the passed trapframe.
While facially a reasonable cleanup this change was motivated
by the need to workaround a compiler bug.
core2_intr(cpu, tf) ->
pmc_process_interrupt(cpu, ring, pmc, tf, inuserspace) ->
pmc_add_sample(cpu, ring, pm, tf, inuserspace)
In the process of optimizing the tail call the tf pointer was getting
clobbered:
(kgdb) up
at /storage/mmacy/devel/freebsd/sys/dev/hwpmc/hwpmc_mod.c:4709
4709 pmc_save_kernel_callchain(ps->ps_pc,
(kgdb) up
1205 error = pmc_process_interrupt(cpu, PMC_HR, pm, tf,
resulting in a crash in pmc_save_kernel_callchain.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
The (eventually) upcoming ath(4) changes will include being able to load
ath(4) devices on the AHB bus (ie the on-die wifi part of the SoC)
as modules.
In order for this to happen, a copy of the calibration data needs to be
copied away before the SPI driver runs or the memory map access hack
won't work.
Now, ideally (!) there'd be some driver that can come up after the MTD
pieces (eg, SPI, NAND, etc) and load into a firmware chunk the calibration
data.
(Or, really really nicely, would be an actual async firmware API that
would lead itself to having a driver schedule a file read - or a raw device
read - to get to the calibration data.)
Now, until all of the above is done - I'm going to perpetuate the layer
breaking atrocity here by simply doing the PCI bus fixup EEPROM/calibration
data hack here. This will work for any AR71xx (and later on, AR231x/AR531x)
device, as well as the handful of QCA MIPS + QCA9880v2 802.11ac boards with
NOR flash.
To use, this goes into the kernel config:
# Enable EEPROM hacks
options AR71XX_ATH_EEPROM
device ar71xx_caldata
device firmware
# This enables the ath_ahb driver (when I commit the change!) to
# pull data out of the firmware hack.
options ATH_EEPROM_FIRMWARE
In the hints file:
# ART calibration data mapping device
hint.ar71xx_caldata.0.at="nexus0"
hint.ar71xx_caldata.0.order=0
# Where the ART is - last 64k in the first 8MB of flash
hint.ar71xx_caldata.0.map.0.ath_fixup_addr=0x1fff0000
hint.ar71xx_caldata.0.map.0.ath_fixup_size=16384
# And now tell the ath(4) driver where to look!
hint.ath.0.eeprom_firmware="ar71xx_caldata.0.map.0.eeprom_firmware"
Tested:
* carambola2, AR933x SoC, using a set of ath and ath_hal modules to load
TODO:
* unify this bit of firmware loading code, as I will definitely need
to include both the PCI bus firmware version (for PCI ID fixups too!)
as well as AHB/on-chip calibration data.
* Commit the ath_ahb bus code
* Convert .. everything over. That'll take the majority of the time.
Tested:
* on IOData WN-G300R. may be same as Sitecom WLR-2100.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D10621
* use ifqmaxlen
* handle (inefficiently for now) meeting padding and alignment requirements for
transmit mbufs.
* change how TX ring handling is done
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D10557
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
As cs is stored in a uint32_t, use the last bit to store the
active high flag as it's unlikely that we will have that much CS.
Reviewed by: loos
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8614
This commit corrects print of nomatch (newline was too early) and fix
unit number for new child in ar5315_spi (was 0, now is -1 to calculate it
according to actual system state)
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: ray, loos, mizhka
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8749
This commit improves code styles like:
- removing commented code
- format comments as C-style
- add spaces after #define-s
It also bring ability to build kernel without INTRNG and remove RedBoot dependency.
Tested on FON2201
Submitted by: Hiroki Sato <yamori813@yahoo.co.jp>
Reviewed by: adrian, mizhka
Approved by: adrian(mentor)
Differential Revision: https://reviews.freebsd.org/D8557
When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().
Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.
While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.
Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070
MFC after: 2 weeks
These are older MIPS4kc parts from Atheros. They typically ran at
sub-200MHz and have 11bg, 11a, or 11abg wifi MAC/PHYs integrated.
This port is the initial non-wifi pieces required to bring up the
chip. I'll commit the redboot and other pieces later, and then
hopefully(!) wifi support will follow.
Submitted by: Mori Hiroki <yamori813@yahoo.co.jp>
Differential Revision: https://reviews.freebsd.org/D7237
* add an ANY debug level which will always echo the message if debugging
is compiled in;
* log MDIO transaction timeouts if debugging is compiled in;
* the argemdio device is different to arge, so turning on MDIO debugging
flags in arge->sc_debug doesn't help. Add a debug sysctl to argemdio
as well so that MDIO transactions can be debugged.
Tested:
* AR9331
For reasons I won't comment on, the AR934x and QCA953x GPIO_OE register
value is inverted - bit set == input, bit clear == output.
So, fix this in the output setting, in reading the initial state from
the boot loader, and also setting any gpiofunc pins that are necessary.
The delta between SENTRY5 and BCM was already small due to BCM being
derived from SENTRY5; re-integrating the two avoids the maintenance
overhead of keeping them both in sync with bhnd(4) changes.
- Re-integrate minor SENTRY5 deltas in bcm_machdep.c
- Modify uart_cpu_chipc to allow specifying UART debug/console flags via
kenv and device hints.
- Switch SENTRY5 to std.broadcom
- Enabled CFI flash support for SENTRY5
Reviewed by: Michael Zhilin <mizkha@gmail.com> (Broadcom MIPS support)
Approved by: re (gjb), adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6897
