MAC address in the EEPROM, and we need to get it from OpenFirmware.
This isn't very pretty but time is lacking to do this in a better
way this near 5.2-RELEASE. This is a RELENG_5_2 candidate.
Original version by: Marius Strobl <marius@alchemy.franken.de>
Tested by: Pete Bentley <pete@sorted.org>
Reviewed by: jake
frame, not the first. It is probably also not safe to free the mbuf chain
as soon as the OWN bit is cleared on the first descriptor since the chip
may not be done copying the frame into the transmit FIFO. Revert the part of
of busdma conversion (if_dc.c rev 1.115) which changed dc_txeof() to look for
the status in the first descriptor and free the mbuf chain when processing
the first descriptor for the frame, and revert the matching changes elsewhere
in the driver. This part of the busdma change caused the driver to report
spurious collisions and output errors, even when running in full-duplex mode.
Reverting the mbuf chain handling slightly complicates dc_dma_map_txbuf(),
since it is responsible for setting the OWN bits on the descriptors, but does
not normally have direct access to the mbuf chain.
Tested by:
Dejan Lesjak <dejan.lesjak at ijs.si> alpha/<Intel 21143 10/100BaseTX>
"Xin LI" <delphij at frontfree.net> i386/<Macronix 98713 10/100BaseTX>
Wiktor Niesiobedzki <bsd at w.evip.pl> i386/<3Com OfficeConnect 10/100B>
Reviewed by: mux
report a hardware rev of 0x00000000. Sadly, the 8169 gigE MAC
also reports 0x00000000, so testing against this for exclusion
results in both cards being skipped by rl_probe(). Make the 8169
test more specific by matching against both the hwrev and the PCI
ID for this chip.
PR: kern/60824
this driver by introducing a flag saying we already stopped the device.
On my Soekris net4801, this took a ping -i 0.001 from spending 80% of
time in interrupt handling to 10% (approx numbers).
This was a particular problem for the net4801 because the tree
interfaces share the same interrupt, but it would be a problem for
any configuration where an unused if_sis interface shares an interrupt
with a busy device.
Other drivers may have similar problems.
Thanks to: Luigi
Only do short-cable on revisions that need it.
Move generic initialization before short-cable fix, in order to not
clobber short cable fix register setting.
code. Both the driver and the new code were wrong. Driver interrupt
handlers are supposed to take "void *vsc" arg, but some including all
COMPAT_ISA drivers and the pci part of the cy driver want an "int unit"
arg. They got this using bogus casts of function pointers which should
have kept working despite their bogusness. However, the new interrupt
code doesn't honor requests to pass an arg of ((void *)0), so things
are very broken if the arg is actually a representation of unit 0.
The fix is to use a normal "void *vsc" arg for the pci case and a
wrapper for the COMPAT_ISA case (of the cy driver). This cleans up
new-busification of the pci case but takes the COMPAT_ISA case a little
further from new-bus. The corresponding bug for the COMPAT_ISA case
has already been fixed similarly using a wrapper in compat_isa.c and
we need another wrapper just to undo that.
Fixed some directly related style bugs (mainly by removing compatibility
cruft).
cy.c:
Fixed an indirectly related old bug in cyattach_common(). A wrong status
was returned in the unlikely event that malloc() failed.
Approved by: re (scottl)
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
- Fail in agp_alloc_gatt if the aperture size is 0 instead of panicing in
contigmalloc.
Reported by: Bjoern Fischer <bfischer@Techfak.Uni-Bielefeld.DE>
Reviewed by: jhb
MFC after: 1 week
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
part of the support is that it still assumes one master and one target
where as AGP 3.0 actually supports multiple devices on the bus.
Submitted by: Keith Whitwell <keith@tungstengraphics.com>
Sponsored by: The Weather Channel
chain passed into dc_encap, which dc_start was unaware of. This caused
the old (now invalid) mbuf to be passed to BPF_MTAP.
Spotted by: Kenjiro Cho <kjc@csl.sony.co.jp>
for 21143 based cards which use SIA mode.
This fixes 10mbit mode for ZNYX ZX346Q cards and other
21143 based cards.
PR: 32118
Submitted by: Rene de Vries <rene@tunix.nl>
Geert Jan de Groot <GeertJan.deGroot@tunix.nl>
Obtained from: BSDI
MFC after: 2 weeks
Tested at 100Mbit only, using Asus P4P800 onboard 3C940.
The -stable version of this patch I have in use for ~2 weeks now, and works
just fine for me.
Based on: Nathan L. Binkert's patch for OpenBSD
Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com>
MFC after: 2 weeks
that has been recorded earlier and overwrite it again later by
reading it directly from the EEPROM again.
Read the MAC address from the PAR0/PAR1 registers instead, which
are autoloaded on reboot.
Tested on AN985, AN983B. According to the datasheets, it should
also work for the AL981 (I don't have such a chip on a card at home)
PR: 52988
Submitted by: Andrew Gordon <arg-bsd@arg.me.uk>
MFC after: 2 weeks
we're on a 32-bit/64-bit bus or not. Use this to decide if we should
set the PCI dual-address cycle enable bit in the C+ command register.
(Enabling DAC on a 32-bit bus seems to do bad things.)
Also, initialize the C+ command register early in the re_init() routine.
The documentation says this register should be configured first.
autoload and then copying the contends of the station address
registers. For some reason, reading the EEPROM on the 8169S doesn't
work right. This gets around the problem, and allows us to read
the station address correctly on the 8169S.
- Insert a delay after initiating packet transmition in re_diag() to
allow lots of time for the frame to echo back to the host, and wait
for both the 'RX complete' and 'timeout expired' bits in the ISR
register to be set.
- Deal more intelligently with the fact that the frame length
field in the RX descriptor is a different width on the 8139C+
than it is on the 8169/8169S/8110S
- For the 8169, you have to set bit 17 in the TX config register
to enter digital loopback mode, but for the 8139C+, you have to
set both bits 17 and 18. Take this into account so that re_diag()
works properly for both types of chips.
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
for the 8169S, according to my sample board. The RealTek Linux driver
mentions 0x00800000. I'm assigning this to the 8110S until I get
more info on it. (The (preliminary) RealTek docs only say that 8169S/8110S
chips will have some combination of those two bits set, but doesn't say
exactly what bit combination goes with which chip variant.)
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).