value that can't ever be in an inconsistant intermediate state even when
some other thread is in the middle of writing the value/register.
Locking of the hardware remains in the few places that do r-m-w operations.
Locking of metadata access is restricted to places using memcpy or sprintf
to modify the metadata.
oddly separated from related functionality. This just moves some blocks
of code around so that setup_intr and teardown_intr are near each other
again, and likewise for enable/disable_intr. No functional changes.
universal.
(1) New struct intr_map_data is defined as a container for arbitrary
description of an interrupt used by a device. Typically, an interrupt
number and configuration relevant to an interrupt controller is encoded
in such description. However, any additional information may be encoded
too like a set of cpus on which an interrupt should be enabled or vendor
specific data needed for setup of an interrupt in controller. The struct
intr_map_data itself is meant to be opaque for INTRNG.
(2) An intr_map_irq() function is created which takes an interrupt
controller identification and struct intr_map_data as arguments and
returns global interrupt number which identifies an interrupt.
(3) A set of functions to be used by bus drivers is created as well as
a corresponding set of methods for interrupt controller drivers. These
sets take both struct resource and struct intr_map_data as one of the
arguments. There is a goal to keep struct intr_map_data in struct
resource, however, this way a final solution is not limited to that.
(4) Other small changes are done to reflect new situation.
This is only first step aiming to create stable interface for interrupt
controller drivers. Thus, some temporary solution is taken. Interrupt
descriptions for devices are stored in INTRNG and two specific mapping
function are created to be temporary used by bus drivers. That's why
the struct intr_map_data is not opaque for INTRNG now. This temporary
solution will be replaced by final one in next step.
Differential Revision: https://reviews.freebsd.org/D5730
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
Linux-driven changes to the way the chip's two interrupt controllers are
defined (we only support one of them) led to no interrupt processing, so
the system would hang after device instantiation. This workaround just
rewrites the FDT data on the fly to get interrupt handling back under the
control of the main GIC device.
If/when we ever support deep sleep modes that involve powering down the
main GIC, we'll have to undo this change, write a driver for the GPC-PIC,
and somehow manage the handoff of responsibilities between the two drivers
as the chip transitions in/out of deep sleep mode.
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
Current functionality is somewhat limited: driver assumes that there
is only one active IPU unit (IPU1) and that video output is DI0 and
video mode is 1024x768. For more advanced functionality driver requires
proper clock management which is work in progress. At the moment driver
assumes that pixel clock is configured by u-boot for 1026x768 mode.
Reviewed by: andrew, ian, mmel
Differential Revision: https://reviews.freebsd.org/D4168
The ci20 port (by kan@) is going to reuse almost all of the intrng code
since the SoC in question looks suspiciously like someone took an ARM
SoC design and replaced the ARM core with a MIPS core.
* migrate out the code;
* rename ARM_ -> INTR_;
* rename arm_ -> intr_;
* move the interrupt flush routine from intr.c / intrng.c into
arm/machdep_intr.c - removing the code duplication and removing
the ARM specific bits from here.
Thanks to the Star Wars: The Force Awakens premiere line for allowing
me a couple hours of quiet time to finish the universe builds.
Tested:
* make universe
TODO:
* The structure definitions in subr_intr.c still includes machine/intr.h
which requires one duplicates all of the intrng definitions in
the platform code (which kan has done, and I think we don't have to.)
Instead I should break out the generic things (function declarations,
common intr structures, etc) into a separate header.
* Kan has requested I make the PIC based IPI stuff optional.
I don't know what alternate universe I was inhabiting when I wrote it
originally, but apparently the basic workings of mathematics were different
than in this universe. I also can't explain how it ever worked, except "by
accident", because completely bogus values were being written into the
divisor register.
so that code shared between imx5 and imx6 can work with OIDs under that node.
Add last_reset_status (integer) and last_reset_reason (string) OIDs that
provide info about the last chip reset (power-on, software reset, watchdog
timeout).
of the SRS (software reset) bit in the watchdog control register. Despite
what the manual seems to imply, this bit DOES trigger an immediate reset, as
opposed to simply flagging the type of reset as software-triggered.
interrupt controller.
The latter is required for INTRNG, because of the hardware erratum
workaround installed by the linux folks into the imx6 FDT data, which remaps
an ethernet interrupt to the gpio device. In the non-INTRNG world we
intercept the call to map the interrupt and map it back to the ethernet
hardware (because we don't need linux's workaround), but in the INTRNG world
we lose the hookpoint where that remapping was happening, but we gain the
ability to work the way linux does by having the gpio driver dispatch the
interrupt.
the name the function will have when the new ARM_INTRNG code is integrated,
and doing this rename first will make it easier to toggle the new interrupt
handling code on/off with a config option for debugging.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
one specific problem: the driver didn't check for ACK/NAK after writing a
slave address byte to the bus, and some slaves signal that they are busy
(such as when completing an internal write to flash memory) by sending a
NAK in response to being addressed.
While working on that problem I discovered that the driver's handling of
error conditions in general didn't match the state transition diagram in
the reference manual, and making that right resulted in a lot of code
reorganization.
Along the way various other changes also happened...
- Remove a mutex that wasn't protecting anything.
- Remove some mystery DELAY()s, document the few that remain.
- Use pause_sbt(9) to yield the processor for the bulk of the time it
takes to transfer each byte rather than busy-polling the whole time.
- Disable the controller when no transfers are in progress; since we
don't operate in slave mode, there's no reason to run the hardware.
- Remove a bunch of unecessary code from probe().
Also, follow the rules from watchdog(9) about what values to return in
various situations (especially, don't touch *error when asked to set a
non-zero timeout that isn't achievable on the hardware).
Also, move the READ/WRITE bus space access macros from the header into the
source file, and rename them to RD2/WR2 to make it clear they're 16-bit
accessors. (READ/WRITE just don't seem like good names to be in a public
header file.)
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
