support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
header parser uses m_pullup(9) to get access to mbuf chain.
m_pullup(9) can allocate new mbuf chain and free old one if the
space left in the mbuf chain is not enough to hold requested
contiguous bytes. Previously drivers can use stale ip/tcp header
pointer if m_pullup(9) returned new mbuf chain.
Reported by: Andrew Boyer (aboyer <> averesystems dot com)
MFC after: 10 days
dev.bce.<unit>.nvram_dump
Add the capability to write the complete contents of the NVRAM via sysctl
dev.bce.<unit>.nvram_write
These are only available if the kernel option BCE_DEBUG is enabled.
The nvram_write sysctl also requires the kernel option
BCE_NVRAM_WRITE_SUPPORT to be enabled. These are to be used at your
own caution. Since the MAC addresses are stored in the NVRAM, if you
dump one NIC and restore it on another NIC the destination NIC's
MAC addresses will not be preserved. A tool can be made using these
sysctl's to manage the on-chip firmware.
Reviewed by: davidch, yongari
calls. Also add BUS_DMA_COHERENT flag to bus_dmamem_alloc(9) to
take advantage of efficient synchronization for architectures that
support that feature.
Reviewed by: davidch
return code. If context was not setup correctly give up
initialization. While I'm here move variable declarations to the
beginning of the function.
Reviewed by: davidch
- Print device details only when verbose boot is enabled.
- Add debug output for shared memory access.
- Add debug statistics (checksum offload & VLAN frame counters).
- Modify TX path to update consumer index for each frame completed
rather than updating the consumer index only once for a group of
frames to improve small packet performance.
- Print driver/firmware pulse messages only when verbose boot
is enabled.
- Add debug sysctl to clear statistics.
- Fix more style(9) violations.
MFC after: 2 weeks
- Added some new debug helper routines to systcl.
- Fixed many of the style(9) violations that have crept into the code
due to my use of a "smart" editor.
MFC after: 2 weeks
parsing code in TSO path as the controller requires VLAN hardware
tagging to make TSO work over VLANs.
While parsing the mbuf in TSO patch, always perform check for
writable mbuf as bce(4) have to reset IP length and IP checksum
field of IP header and make sure to ensure contiguous buffer before
accessing IP/TCP headers. While I'm here replace magic number 40 to
more readable sizeof(struct ip) + sizeof(struct tcphdr).
Reviewed by: davidch
TX/RX checksum handler to set/clear relavant assist bits which was
used to cause unexpected results.
With this change, bce(4) can be bridged with other interfaces that
lack TSO, VLAN checksum offloading.
Reviewed by: davidch
around. Management firmware(ASF/IPMI/UMP) requires the VLAN
hardware tag stripping so don't actually disable VLAN hardware tag
stripping. If VLAN hardware tag stripping was disabled, bce(4)
manually reconstruct VLAN frame by appending stripped VLAN tag.
Also remove unnecessary IFCAP_VLAN_MTU message.
Reviewed by: davidch
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
splitting in bce(4) instead of (ab)using ZERO_COPY_SOCKETS that was not
propagated into if_bce.c anyway. It is disabled by default.
Approved by: davidch
MFC after: 3 days
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
- Added missing firmware for 5709 A1 controllers.
- Changed some debug statistic variable names to be more consistent.
Submitted by: davidch
MFC after: Two weeks
a real packet error but simply indicate that an unexpected unicast or multicast
error was received by the NIC, which was not counted in the past as well.
Reported by: many (on -stable@)
Reviewed by: davidch
MFC after: 3 days
change. As a side effect, this makes the excessive interrupts to
disappear which has been observed as a regression in recent stable/7.
Reported by: many (on -stable@)
Reviewed by: davidch
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
- Added some additional code for debug builds.
- Fixed a problem printing physical memory on 64bit system during debugging.
- Modified some of the context memory and mailbox register names to more
clearly distinguish their use.
- Added memory barriers for Intel CPUs when accessing host memory data
structures which are written by hardware.
MFC after: Two weeks.
- Fixed a problem on i386 architecture when using split header/jumbo frame
firmware caused by hardware alignment requirements.
- Added #define BCE_USE_SPLIT_HEADER to allow the feature to be enabled/
disabled. Enabled by default.
PR: kern/123696
MFC after: 2 weeks
