-stable machine via the old-school methods):
Use __FreeBSD_version in preference to __FreeBSD__ >= N where possible.
Define a single variable mythread which is set to curproc or curthread
depending on the OS version (with a comment saying it is a white lie on
4.x since it really is a proc).
NB: __FreeBSD__ is the OS level of the host machine, not the target,
and should never be used, if possible, as __FreeBSD__ >= N.
Rev 1.56 of if_dc.c removed calls to mii_pollstat() from the dc_tick()
routine. dc_tick() is called regularly to detect link up and link down
status, especially when autonegotiating.
The expectation was that mii_tick() (which is still called from dc_tick())
would update status information automatically in all cases where it would
be sensible to do so.
Unfortunately, with authentic 21143 chips this is not the case, and
the driver never successfully autonegotiates. This is because (despite
what it says in the 21143 manual) the chip always claims that link is not
present while the autonegotiation enable bit is set. Autonegotation takes
place and succeeds, but the driver tests the link bits before it switches
off the autonegotiation enable bit, and success is not recognised.
The simplest solution is to call dcphy_status() more often for MII_TICK
calls by dropping out of the switch statement instead of exiting when
we are autonegotiating and link appears to not be present. When
autonegotiation succeeds, dcphy_status() will note the speed and fdx/hdx
state and turn off the autonegotiation enable bit. The next call to
dcphy_status() will notice that link is present, and the dc driver code
will be notified.
Macronix chips also use this code, but implement link detection as
described in the manual, and hence don't need this patch. However, tests
on a Macronix 98715AEC-C show that it does not adversely affect them.
This could be done better but is the minimal effective change, and most
closely mimics what was happening prior to rev 1.56 of if_dc.c. (Actually
I also deleted a small amount of unnecessary code while I was in the area.)
Reviewed by: wpaul
loop is inversly proportional to hz.
This makes things more sane for configurations with hz != 100.
Cosmetic: Make the loops look similar to the loops in digi.c
loop is inversly proportional to hz.
This makes things more sane for configurations with hz > 100.
Submitted by: Peter Jeremy <peter.jeremy@alcatel.com.au>
environment needed at boot time to a dynamic subsystem when VM is
up. The dynamic kernel environment is protected by an sx lock.
This adds some new functions to manipulate the kernel environment :
freeenv(), setenv(), unsetenv() and testenv(). freeenv() has to be
called after every getenv() when you have finished using the string.
testenv() only tests if an environment variable is present, and
doesn't require a freeenv() call. setenv() and unsetenv() are self
explanatory.
The kenv(2) syscall exports these new functionalities to userland,
mainly for kenv(1).
Reviewed by: peter
- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
lun address modifier of sorts. Only an HP XP-512 seems to have cared.
Fix a few misplaced pointers for the new fabric goop, which has been
demonstrated to work on newer Brocades and McData switches now.
Put in commented out code which would run GFF_ID if the QLogic f/w
allowed it.
Don't whine about not being able to find a handle for a command if it
was a command aborted (by us).
o move timeout from wihap_info to wihap_sta_info
o sprinkle spls into the code (need to use proper -current locking)
o better use of le16toh and htole16
o fix a few leaks m_freem(m)
o minor knf
o minor de-knf to match OpenBSD
o de__P
- Add a device_method_t array, fore_methods.
- Add a fore_ident_table that contains the various FORE Systems PCA-200
series devices.
- Rewrite of the fore_probe routine (formerly known as fore_pci_probe).
- Minor changes... mostly WIP stuff to get this updated... still much to
be done.
the per-channel bus_addr_t offset. Also, cast the offset to (long long)
and use %#llx instead of %#x to fix printf warnings on architectures where
sizeof(bus_addr_t) != sizeof(int).
es137x.c: In function `es1371_rdcd':
es137x.c:598: warning: `x' might be used uninitialized in this function
PR: kern/35408
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
that declares itself to be a disk, which may be the wrong thing to do in
the long term but it works well enough to attach to emulated disks in the
PowerPC simulator in gdb now that they have the proper device_type
property.
The extra microphone channel capability is part of the "normal" ac97
capabilities and not an extended ac97 capability. Now recording on
codecs without a seperate mic channel works.
MFC after: 1 week
FIFO or the in-RAM descriptors it will switch to RX_IDLE from where it
is not restarted.
We used to deal with RX_IDLE by doing a total reinit but this lost
our link and caused a potential 30sec autonegotiation against
switches. This was changed to a less heavyhanded approach, but this
failed to restart the receiver it it were in the RX_IDLE state.
This change adds the RX_IDLE and the RX_FIFO_OFLOW conditions as
triggers for interrupts and receive side processing, and restarts
the receiver when it is RX_IDLE.
Remove the #ifdef notyet'ed nge_rxeoc() function.
Sponsored by: Cybercity Internet, Denmark.
MFC after: 7 days
(apparently by markus@, at least committed by him). This has the
advantage of not using the bad IV's from Fluhrer/Mantin/Shamir as well
as bringing the drivers a little closer together.
Also use a few constants in place of magic numbers in one place.
Obtained from: OpenBSD 1.25, 1.28, 1.36, 1.38, 1.42
time we tell CAM to rescan the bus. Together with the previous patch
this should avoid the problem where the devices would wedge because they
got spoken to over two different pipes.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
wrote. This code was for 4.5-release, so I've ported it to -current
and made a few minor tweaks. The biggest non-style tweak was to not
make access point the default.
More changes will be needed to get this actually working, but I wanted
to get a relatively pure baseline. This doesn't seem to break what
works now.
attachment after boot in some cases where the device gets confused if
spoken to over two different pipes simultaneously (resulting in TIMEOUT
errors on requesting INQUIRY data).
This solution is far from perfect, as after umass_attach has returned
the USB stack fetches the string descriptors in order for creating the
event that is sent to userland. It just makes the chances of collisions
less likely.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
submitter, this permits Russian (and probably other locales') characters
to be entered via watch(8).
PR: 35636
Submitted by: Gleb Smirnoff <glebius@rinet.ru>
the card for command completion.
digi_delay() uses either tsleep() or DELAY() depending on the value of
``cold''.
Pointed in the right direction by: jhb
Add the card name to the error message for the first initialisation
failure, giving us more info about what was actually discovered.
This code has been tested by Robert Suetterlin <robert@mpe.mpg.de>
to work on a PCI Xem card.
mod_depend * (which may be NULL). The only consumer of this
function at the moment is digi_loadmoduledata(), and that passes
a NULL mod_depend *.
In linker_reference_module(), check to see if we've already got
the required module loaded. If we have, bump the reference count
and return that, otherwise continue the module search as normal.
newer ultras and probably other sun machines. This is a pretty decent
chip with 32 byte read and write fifos and support for many higher baud
rates. It supports hdlc and sdlc as well as asynchronoue serial, but the
goal here is just decent serial console support for the sparc64 port, so
these modes are not expected to be supported. So far this only has support
for the low level routines used by kernel printf and thus ddb over serial,
a character device which can be used for login consoles has not yet been
written.
doesn't support NWAY, the RealTek PHY (both the integrated ones on 8139
chips and the RTL8201L 10/100 PHY) will not report the link speed via
the ANLPAR or BMSR registers. For the 8201L, we need to look in magic
vendor-specific PHY register 0x19. For the 8139 MAC+PHY combo, we have
to be able to test the RL_MEDIASTAT register.
The changes to rlphy.c are based largely on the patch from PR 30836,
however I tried to eliminate some magic numbers by creating an entry
for the 8201 PHY in miidevs.
Also updated if_rl.c to allow the rlphy driver to read the RL_MEDIASTAT
register via the rl_miibus_readreg() routine.
revision 1.153
date: 2002/02/11 11:40:33; author: augustss; state: Exp; lines: +67 -26
Switch to the same abort mechanism as in [eo]hci; it should be more
robust.
revision 1.151
date: 2002/01/27 23:00:34; author: augustss; state: Exp; lines: +3 -3
Use M_WAITOK instead of M_NOWAIT when allocating extra descriptors.
Spotted by OpenBSD.
date: 2000/12/29 01:47:49; author: augustss;
Supply our own report descriptor (from Nick Hibma) for the Wacom Graphire.
The descriptor it reports is broken.
XXX Not tested, because I don't have the device.
date: 2001/08/15 00:06:49; author: augustss; state: Exp; lines: +3 -1
If there was a vendor+product locator match return a higher match value.
Rationale, if you have a device (e.g., a mouse) with a more specific
driver but want to recognize it with the more generic driver you can
do that by supplying vendor and product locators for the generic one.
revision 1.101
date: 2001/02/20 15:20:32; author: minoura;
Re-initialize some registers after resuming from suspend.
Some APM BIOSes do not restore them.
Reviewd by augustss.
revision 1.97
date: 2000/12/31 14:29:54; author: augustss; state: Exp; lines: +17 -3
Make the controller survive suspend/resume. Thanks to Steve Woodford
<steve@mctavish.co.uk> for testing.
revision 1.95
date: 2000/12/13 03:09:06; author: augustss; state: Exp; lines: +19 -3
Make the ohci driver not hang suspend/resume. It still doesn't resume
correctly. From itohy@netbsd.org (ITOH Yasufumi) PR kern/11714.
revision 1.58
date: 2001/11/20 23:53:26; author: augustss; state: Exp; lines: +61 -33
Create a special kernel thread to run the usb short lived tasks (instead
of using the device discovery threads).
revision 1.65
date: 2002/01/03 22:20:45; author: augustss; state: Exp; lines: +9 -2
Add a DIAGNOSTIC check. From FreeBSD.
(Just wrap these changes, that we already had, with a #ifdef DIAGNOSTIC).
revision 1.62
date: 2002/01/02 20:55:58; author: augustss; state: Exp; lines: +11 -10
Some more usb_proc_ptr changes.
Also some minor stylistic changes.
revision 1.63
date: 2002/01/02 20:58:12; author: augustss; state: Exp; lines: +4 -4
Fix typo in last commit.
revision 1.64
date: 2002/01/02 22:44:44; author: augustss; state: Exp; lines: +7 -4
Add a comment.
The usb_proc_ptr changes were introduced in 1.62 and backed out in 1.64.
revision 1.61
date: 2001/12/31 15:55:51; author: augustss; state: Exp; lines: +3 -5
Delay bus enumeration a little in case the controller is a companion
controller. This way the main controller can gain ownership of the port
before enumeration starts.
date: 2001/11/20 23:53:26; author: augustss; state: Exp; lines: +61 -33
Create a special kernel thread to run the usb short lived tasks (instead
of using the device discovery threads).
The change to usb_port.h is a little hack whilst I address an issue
with NetBSD.
revision 1.68
date: 2001/12/24 21:36:16; author: augustss; state: Exp; lines: +2 -1
Add some more DIAGNOSTIC tests.
Make usb_match_device() match on USB_PRODUCT_ANY.
if_cuereg.h (1.5), if_kue.c (1.11), if_kuereg.h (1.5)
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
We don't have ratecheck() in our kernel yet, so I've hardcoded
usb_ratecheck() to return true always.
usbdi.c (1.86), usbdivar.h (1.66)
[Some partial, because most of this was merged in a while ago]
date: 2001/11/20 13:48:03; author: augustss;
Keep track of device speed for USB 2.0.
revision 1.106
date: 2001/11/09 15:01:57; author: augustss; state: Exp; lines: +73 -57
Fix a bug in xfer abort processing when the HC executes ahead of what
the driver aborts.
Don't block RHSC interrupts.
revision 1.103
date: 2001/09/11 07:00:19; author: augustss; state: Exp; lines: +4 -1
Don't go top mode OPERATIONAL (before reset) on startup even
if BIOS claims to have initialized the controller.
hw.syscons.saver.keybonly: used to specify that only input is to
interrupt the screensaver. This allows one to run a chatty console
app but still have the screen blank out until a key is pressed.
There should probably also be an ioctl for this, we'll do that later.
hw.syscons.saver.blanktime: exports the screensaver timeout via sysctl.
Submitted by: Olivier Houchard <doginou@cognet.ci0.org>
interface that is compatible with the LUCENT or HERMES firmware.
Instead, it is like the various No Wires Necessary products that were
produced a while ago and then sold to intersil. It will require a
different driver altogether. Remove it from the list of supported
cards.
The 3CRWE777A apperas to be a re-badged SMC 2602W card, so the driver
appears to support it. Add it to the list.
Thanks to Todd Miller for loaning me the card during tonight's FRUUG
meeting for testing against CU's wireless infrastructure.
Grumble. I've seen better documented architectures out of Redmond.
Redo fabric evaluation to not use GET ALL NEXT (GA_NXT). Switches seem
to be trying to wriggle out of supporting this well. Instead, use
GID_FT to get a list of Port IDs and then use GPN_ID/GNN_ID to find the
port and node wwn. This should make working on fabrics a bit cleaner and
more stable.
This also caused some cleanup of SNS subcommand canonicalization so that
we can actually check for FS_ACC and FS_RJT, and if we get an FS_RJT,
print out the reason and explanation codes.
We'll keep the old GA_NXT method around if people want to uncomment a
controlling definition in ispvar.h.
This also had us clean up ISPASYNC_FABRICDEV to use a local lportdb argument
and to have the caller explicitly say that a device is at the end of the
fabric list.
MFC after: 1 week
time-of-day clocks, ported from NetBSD. The front-ends are expected
to be at least partly machine-dependent; the sparc64 EBus and SBus
ones will be commited to MD directories for now (in a subsequent commit).
wi.c 1.64: Table driven IDs (ichiro)
1.59: Don't use magic numbers (ichiro)
Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent
cards (and submit those changes back to ichiro-san)
Obtained from: NetBSD
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
o OpenBSD's wiconfig tells me that a value of '2' is for sony wireless
cards, 1 is for lucent (which we already knew) and '5' is for embedded
lucent cards.
o Move some RID definitions to if_wavelan_ieee.h and use NetBSD names
more often.
# more work is still needed in this area.
interrupts. This is a bit harder than it needs to be because there's
more than one way to generate link attentions, at least one of which
does not work on the BCM5700, but does on the 5701.
For the 5701, we can safely use the 'link changed' bit in the status
block, and we enable link change attentions in the mac event register.
For the 5700, we have to use MII interrupts, which require checking
the MAC status register rather than the status block. This requires
doing an extra register access on each interrupt which I'd prefer to
avoid, but them's the breaks. Testing with both a 3c996-T and 3c996B-T
shows that we do in fact detect the link going up and down properly
on cable insertions/disconnections.
Also, avoid twiddling the autopoll enable bit in the MI mode register
when doing a PHY read. I think this coupled with the other changes
will stop the interrupt storms Paul Saab has been harassing me about.
Manually setting the link to 100baseTX full duplex seems to work ok
for me. (I'm typing over the 3c996B-T right now.)
Lastly, teach the driver how to recognize a 3c996B-SX by checking
the hardware config word in the EEPROM in order to detect the media.
We attach 5701 fiber cards correctly now, but I haven't verified that
they send/receive packets yet since I don't have a second fiber
interface at home. (I know that fiber 5700 cards work, so I'm
keeping my fingers crossed.)
This driver was written by Myson and is made available
by their courtesy.
The 5.x version is not fully tested (I will be testing) but
the 4.x version has been tested by many.
I will commit it soon.
Myson have their own chip design based on the DEC 214xx family but
with several differences. Myson sells this chip to several
EOMs in teh Chinese area so there may be many noname brand cards
that respond to this driver. Myson will be supplying a list
of some of these.
1) Properly detect the Symbol based cards (The 3Com Airconnect and their
ilk) and only reset them *ONCE* ever. This appears to make them work,
but more testing is needed. The tests that would wedge up my machine
completely now appear to work, but I have not real access points
handy.
2) Report both the Station firmware and the Primary firmware on Prism
based cards. On Lucent based cards, only report the station firmware
since that's all it supports. On symbol cards, report the symbol
specific firmware name as its station firmware.
3) Better Prism 2.5 and 3 family names. We really need to go table
driven for this.
4) Workaround for bugs in Intersil's firmware is only needed for at most
0.8.2 and earlier, since 0.8.3 and later appear to work.
Obtained from: NetBSD
stuff was right, but the busdma stuff was massively not right.
Didn't really test on ia64 or i386- don't have the former h/w and my
FreeBSD-current disk is unwell right now. Hope that this is okay.
MFC after: 1 week
"raw partition" of any kind since the floppy driver doesn't support
UFS-style partitions at all.
Reported by: "Crist J. Clark" <crist.clark@attbi.com>
Reviewed by: bde
MFC after: 3 days
date: 2001/08/15 00:04:59; author: augustss;
Add a little infrastructure so that individual drivers can easily check
if thee was a vendor+product locator match.
DIOCGMEDIASIZE instead.
The partition type check has been XXX'ed out since we cannot expect
that a BSD disklabel with a type field be available on all platforms.
revision 1.50
date: 2001/04/12 01:18:24; author: thorpej; state: Exp; lines: +6 -2
Only if __HAVE_GENERIC_SOFT_INTERRUPTS is then splusb == splsoftnet
(because we register the interrupt with IPL_SOFTNET). However, if
we're using a callout, then splusb == splsoftclock (because the
callouts happen from the softclock interrupt).
Note that splsoftnet blocks softclock interrupts, but this is
meant to better describe what's going on.
date: 2001/01/21 19:00:06; author: augustss;
Change the operation of the USB event thread. Before it only
performed USB device discovery, now it can also perform (short)
tasks for device drivers that need a process context, but don't
have one. This is not pretty, but better than using busy-wait
in an interrupt context.
o 3Com 3crwe62092a
o Addtron awp100
o No Wires Necessary WLAN 550 and 1148
o Proxim RANGELANDS 8340
and reorder linksys to be in proper sort order.
Obtained from: OpenBSD (mostly)
revision 1.138
date: 2001/10/02 17:59:38; author: pooka; state: Exp; lines: +6 -6
move DIAGNOSTIC-printf up one block to make it reachable
noted by Christophe Kalt in private email
(1.39), usbdi.c (1.79), usbdi.h (1.47), usbdivar.h (1.62)
date: 2001/01/21 02:39:52; author: augustss;
Add code to use soft interrupt to handle USB interrupt processing.
Don't enable the code since it doesn't work with the kludgy Ethernet
drivers.
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
revision 1.58
date: 2000/06/24 04:12:53; author: thorpej; state: Exp; lines: +5 -2
Kill SPLUSBCHECK -- it's not portable, and quite annoying on some
platforms which otherwise function just fine.
revision 1.127
date: 2000/11/22 05:50:59; author: soren; state: Exp; lines: +5 -5
In uhci_intr(), only warn about power state confusion if the
interrupt was actually for us.
date: 2000/08/08 19:51:46; author: tv; state: Exp; lines: +24 -13
%b -> bitmask_snprintf()
Because this code is shared, add a macro for bitmask_snprintf()
that should expand to the equivalent snprintf() on non-NetBSD
systems. This is only used in ?HCI_DEBUG cases anyway.
revision 1.81
date: 2000/10/24 15:01:26; author: augustss; lines: +36 -10
Add a hack to try and figure out if the TI UTUSB41 hub is bus
powered despite claiming to be self powered (it's important to
know so that the power budget can be met).
Part of this got merged in a previous commit, but not all.
revision 1.72
date: 2000/04/14 14:13:56; author: augustss; state: Exp; lines: +34 -27
Make attach of ugen work as it should so product&vendor locators
can be used.
usb.c 1.40:
revision 1.40
date: 2000/03/14 23:13:12; author: augustss; state: Exp; lines: +4 -1
Make sure the USB event thread discovers all devices first time
it call usb_discover(). It should now be possible to have the
root NFS mounted over a USB Ethernet Adapter.
----------------------------
revision 1.73
date: 2000/05/31 16:14:42; author: augustss; state: Exp; lines: +19 -6
Be more careful when setting the alternate interface so we don't
end up with nothing set at all if it fails.
----------------------------
----------------------------
revision 1.117
date: 2000/05/30 09:26:06; author: augustss; lines: +7 -1
As a safety, check that the controller is not suspended when we get
an interrupt.
----------------------------
ohci.c (1.85), ohcireg.h (1.17):
----------------------------
date: 2000/04/01 09:27:35; author: augustss;
Add a delay before reading the number of ports from the controller to
avoid getting 0 from it.
----------------------------
ohci.c (1.83), ohcireg.h (1.16), ohcivar.h (1.21)
===================================================================
date: 2000/03/29 01:46:26; author: augustss;
A first stab at support for isochronous transfers.
===================================================================
Caveats:
The new savecore program is not complete in the sense that it emulates
enough of the old savecores features to do the job, but implements none
of the options yet.
I would appreciate if a userland hacker could help me out getting savecore
to do what we want it to do from a users point of view, compression,
email-notification, space reservation etc etc. (send me email if
you are interested).
Currently, savecore will scan all devices marked as "swap" or "dump" in
/etc/fstab _or_ any devices specified on the command-line.
All architectures but i386 lack an implementation of dumpsys(), but
looking at the i386 version it should be trivial for anybody familiar
with the platform(s) to provide this function.
Documentation is quite sparse at this time, more to come.
Details:
ATA and SCSI drivers should work as the dump formatting code has been
removed. The IDA, TWE and AAC have not yet been converted.
Dumpon now opens the device and uses ioctl(DIOCGKERNELDUMP) to set
the device as dumpdev. To implement the "off" argument, /dev/null
is used as the device.
Savecore will fail if handed any options since they are not (yet)
implemented. All devices marked "dump" or "swap" in /etc/fstab
will be scanned and dumps found will be saved to diskfiles
named from the MD5 hash of the header record. The header record
is dumped in readable format in the .info file. The kernel
is not saved. Only complete dumps will be saved.
All maintainer rights for this code are disclaimed: feel free to
improve and extend.
Sponsored by: DARPA, NAI Labs
have ripped all the i386 specific formatting code from their
dump routines. Due to the potential for trashing disks, I did
not want to do this "blind".
(65536 * 32 - 1), but MAKEDEV only supports up to (32 * 32 -1). Device
names use the unit number in base 32 for all "digits".
This required fixing an old bug in MAKEDEV:ttyminor(). Its arg was the
global $unit instead of $1.
Reminded by: Valentin K. Ponomarenko <valka@krog.ukrtel.net>
MFC-after: 1 week
measured accurately for periodic interrupts provided the interrupts
don't need to be serviced very quickly to keep their period almost
constant. sio output interrupts have this property (interrupt service
can be delayed for up to 1 character time without the period changing).
This is non-optional and undocumented so that it can be added and
removed easily. It has no significant effect unless it is enabled by
hacking on a variable using a debugger. Hardclock and statclock interrupts
would work even better for this, at least on i386's, provided their
interrupt handlers are fast (as they are in -current but not in -stable
or in my version of -current).
allows us to properly parse cards with attribute memory based CIS that
before wouldn't parse correctly, sometimes with a panic. This allows
me to get my 3C562 modem/ethernet card to fail to attach due to
problems in the ep and sio drivers rather than due to problems in the
CIS parsing code :-).
We weren't setting the address to jump to for the function entries.
This caused us to only work when the addional entries were after the
first ones. On the 3C562/3C563 card this was not the case.
We were also mapping Attribute memory when common memory was asked for
in the target of the LONGLINK_{A,C} or LONGLINK_MFC.
My IBM Home And Away Modem/LAN card still fails for reasons unknown.
This completes the ATA RAID support, since all functions to manipulate
the RAID are accessible from FreeBSD, the BIOS on the ATA RAID cards
are only nessesary for booting.
I decided to allow for creation of ATA RAID's on any ATA controller, but
please keep in mind the restrictions on that. Due to the BIOS not
knowing what to do you can only boot from a RAID1 or the first disk
in a SPAN, if its not located on a "real" ATA RAID controller like
the Promise or Highpoint controllers.
Sponsored by: Advanis
The conclusion is that this method really can tell the perfect from the
less than perfect ACPI counters.
It is in fact probably a bit more discriminative than that, but we
will rather condemn some otherwise perfect counters to the slightly
slower "-safe" version, than certify a counter as perfect which
will let us down later.
Many thanks to all the people who sent email reports!
by the hardware are still marked as owned. Handle this by installing a
timeout handler to collect this descriptor to avoid having received
packets remain unhandled until the next one arrives.
- remove some useless code from the status change handler that was intended
to enable the the MII drivers for external phys; this is already done
during interface initialization, and the deleted code made some
assumptions about phy addresses that do not seem to hold true on newer
cards. This should get at least one of the two hmes of newer Netra t1
machines working.
- correct the interrupt resource allocation
- bump the number of RX descriptors, lower values cause promblems on some
machines
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
3c996B-T, with the 5701 rev B5 ASIC). One thing that confuses me
still is that the 'link state change' bit in the status block seems
to change state an awful lot. I have a workaround for this in place
now, but it needs more investigation. For the moment though, this
is enough to get the driver to work with this card.
soon because it's just getting harder and harder to find switches
that correctly implement the GET ALL NEXT subcommands for the SNS
protocol.
Latch up result out pointer and set a busy flag when we're looking
at the response queue. This allows for a cleaner way to make sure
we don't get multiple CPUs trying to read the same response queue
entries.
Change how isp_handle_other_response returns values (clarity).
Make PORT UNAVAILABLE the same as PORT LOGOUT (force a LIP).
Do some formatting changes.
MFC after: 0 days
keep gcc-3.1+ happy:
ata-all.c:410: warning: deprecated use of label at end of compound statement
ata-all.c:587: warning: deprecated use of label at end of compound statement
ata-raid.c:99: warning: deprecated use of label at end of compound statement
ata-raid.c:151: warning: deprecated use of label at end of compound statement
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
"Fixed" format printf error in previous commit. This file is not
formatted in KNF. Partially restore bug for bug compatibility: indent
the printf args too much, but don't format them for 160-column terminals.
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
