reported, on APs. We already did this on BSP.
Otherwise, the userspace software which depends on the features
reported by the high CPUID levels is misbehaving. In particular, AVX
detection is non-functional, depending on which CPU thread happens to
execute when doing CPUID. Another victim is the libthr signal
handlers interposer, which needs to save full FPU extended state.
Reported and tested by: Andre Meiser <ortadur@web.de>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
rev. 55. The modern CPUs cache and TLB descriptions looked quite
questionable without the update, e.g. Haswell i7 4770S reported:
Data TLB: 4 KB pages, 4-way set associative, 64 entries
L2 cache: 256 kbytes, 8-way associative, 64 bytes/line
After the update, the report is:
Data TLB: 1 GByte pages, 4-way set associative, 4 entries
Data TLB: 4 KB pages, 4-way set associative, 64 entries
Instruction TLB: 2M/4M pages, fully associative, 8 entries
Instruction TLB: 4KByte pages, 8-way set associative, 64 entries
64-Byte prefetching
Shared 2nd-Level TLB: 4 KByte/2MByte pages, 8-way associative, 1024 entries
L2 cache: 256 kbytes, 8-way associative, 64 bytes/line
Some tags were apparently removed from the table 3-21, Vol. 2A. Keep
them around, but add a comment stating the removal.
Update the format line for cpu_stdext_feature according to the bits
from the SDM rev.55. It appears that Haswells do not store %cs and
%ds values in the FPU save area.
Store content of the %ecx register from the CPUID leaf 0x7
subleaf 0 as cpu_stdext_feature2 and print defined bits from it,
again acording to SDM rev. 55.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
interacts with interrupts, query ACPI and use MWAIT for entrance into
Cx sleep states. Support C1 "I/O then halt" mode. See Intel'
document 302223-007 "Intelб╝ Processor Vendor-Specific ACPI Interface
Specification" for description.
Move the acpi_cpu_c1() function into x86/cpu_machdep.c and use
it instead of inlining "sti; hlt" sequence in several places.
In the acpi(4) man page, besides documenting the dev.cpu.N.cx_methods
sysctl, correct the names for dev.cpu.N.{cx_usage,cx_lowest,cx_supported}
sysctls.
Both jkim and avg have some other patches implementing the mwait
functionality; this work is unrelated. Linux does not rely on the
ACPI to provide correct tables describing Cx modes. Instead, the
driver has pre-defined knowledge of the CPU models, it was supplied by
Intel.
Tested by: pho (previous versions)
Sponsored by: The FreeBSD Foundation
sys/i386/i386/machdep.c to new file sys/x86/x86/cpu_machdep.c. Most
of the code is related to the idle handling.
Discussed with: pluknet
Sponsored by: The FreeBSD Foundation
Features by CPUID as CPUID.80000008H:EAX[7:0], into variable cpu_maxphyaddr.
Reviewed by: alc
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Move the existing code to x86/x86/identcpu.c since it is x86-specific.
- If the CPUID2_HV flag is set, assume a hypervisor is present and query
the 0x40000000 leaf to determine the hypervisor vendor ID. Export the
vendor ID and the highest supported hypervisor CPUID leaf via
hv_vendor[] and hv_high variables, respectively. The hv_vendor[]
array is also exported via the hw.hv_vendor sysctl.
- Merge the VMWare detection code from tsc.c into the new probe in
identcpu.c. Add a VM_GUEST_VMWARE to identify vmware and use that in
the TSC code to identify VMWare.
Differential Revision: https://reviews.freebsd.org/D1010
Reviewed by: delphij, jkim, neel
<machine/md_var.h>.
- Move some CPU-related variables out of i386/i386/identcpu.c to
initcpu.c to match amd64.
- Move the declaration of has_f00f_hack out of identcpu.c to machdep.c.
- Remove a misleading comment from i386/i386/initcpu.c (locore zeros
the BSS before it calls identify_cpu()) and remove explicit zero
assignments to reduce the diff with amd64.
registers also on other CPUs, besides the CPU which happens to execute
the ddb. The debugging registers are stored in the pcpu area,
together with the command which is executed by the IPI stop handler
upon resume.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
introduced with the IvyBridge CPUs. Provide the definitions for new
bits in CR3 and CR4 registers.
Tested by: avg, Michael Moll <kvedulv@kvedulv.de>
MFC after: 2 weeks
mostly meets the guidelines set by the Intel SDM:
1. We use XRSTOR and XSAVE from the same CPL using the same linear
address for the store area
2. Contrary to the recommendations, we cannot zero the FPU save area
for a new thread, since fork semantic requires the copy of the
previous state. This advice seemingly contradicts to the advice
from the item 6.
3. We do use XSAVEOPT in the context switch code only, and the area
for XSAVEOPT already always contains the data saved by XSAVE.
4. We do not modify the save area between XRSTOR, when the area is
loaded into FPU context, and XSAVE. We always spit the fpu context
into save area and start emulation when directly writing into FPU
context.
5. We do not use segmented addressing to access save area, or rather,
always address it using %ds basing.
6. XSAVEOPT can be only executed in the area which was previously
loaded with XRSTOR, since context switch code checks for FPU use by
outgoing thread before saving, and thread which stopped emulation
forcibly get context loaded with XRSTOR.
7. The PCB cannot be paged out while FPU emulation is turned off, since
stack of the executing thread is never swapped out.
The context switch code is patched to issue XSAVEOPT instead of XSAVE
if supported. This approach eliminates one conditional in the context
switch code, which would be needed otherwise.
For user-visible machine context to have proper data, fpugetregs()
checks for unsaved extension blocks and manually copies pristine FPU
state into them, according to the description provided by CPUID leaf
0xd.
MFC after: 1 month
64bit and 32bit ABIs. As a side-effect, it enables AVX on capable
CPUs.
In particular:
- Query the CPU support for XSAVE, list of the supported extensions
and the required size of FPU save area. The hw.use_xsave tunable is
provided for disabling XSAVE, and hw.xsave_mask may be used to
select the enabled extensions.
- Remove the FPU save area from PCB and dynamically allocate the
(run-time sized) user save area on the top of the kernel stack,
right above the PCB. Reorganize the thread0 PCB initialization to
postpone it after BSP is queried for save area size.
- The dumppcb, stoppcbs and susppcbs now do not carry the FPU state as
well. FPU state is only useful for suspend, where it is saved in
dynamically allocated suspfpusave area.
- Use XSAVE and XRSTOR to save/restore FPU state, if supported and
enabled.
- Define new mcontext_t flag _MC_HASFPXSTATE, indicating that
mcontext_t has a valid pointer to out-of-struct extended FPU
state. Signal handlers are supplied with stack-allocated fpu
state. The sigreturn(2) and setcontext(2) syscall honour the flag,
allowing the signal handlers to inspect and manipilate extended
state in the interrupted context.
- The getcontext(2) never returns extended state, since there is no
place in the fixed-sized mcontext_t to place variable-sized save
area. And, since mcontext_t is embedded into ucontext_t, makes it
impossible to fix in a reasonable way. Instead of extending
getcontext(2) syscall, provide a sysarch(2) facility to query
extended FPU state.
- Add ptrace(2) support for getting and setting extended state; while
there, implement missed PT_I386_{GET,SET}XMMREGS for 32bit binaries.
- Change fpu_kern KPI to not expose struct fpu_kern_ctx layout to
consumers, making it opaque. Internally, struct fpu_kern_ctx now
contains a space for the extended state. Convert in-kernel consumers
of fpu_kern KPI both on i386 and amd64.
First version of the support for AVX was submitted by Tim Bird
<tim.bird am sony com> on behalf of Sony. This version was written
from scratch.
Tested by: pho (previous version), Yamagi Burmeister <lists yamagi org>
MFC after: 1 month
processors. With this workaround, superpage promotion can be re-enabled
under virtualization. Moreover, machine check exceptions can safely be
enabled when FreeBSD is running natively on Family 10h processors.
Most of the credit should go to Andriy Gapon for diagnosing the error and
working with Borislav Petkov at AMD to document it. Andriy also reviewed
and tested my patches.
Discussed with: jhb
MFC after: 3 weeks
not properly set up. r199067 added the call to TUNABLE_INT_FETCH() to
initializecpu() that results in hang because AP are started when kernel
environment is already dynamic and thus needs to acquire mutex, that is
too early in AP start sequence to work.
Extract the code that should be executed only once, because it sets
up global variables, from initializecpu() to initializecpucache(),
and call the later only from hammer_time() executed on BSP. Now,
TUNABLE_INT_FETCH() is done only once at BSP at the early boot stage.
In collaboration with: Mykola Dzham <freebsd levsha org ua>
Reviewed by: jhb
Tested by: ed, battlez
established, OS shall flush the caches on all processors that may have
used the mapping previously. This operation is not needed if processors
support self-snooping. If not, but clflush instruction is implemented
on the CPU, series of the clflush can be used on the mapping region.
Otherwise, we have to flush the whole cache. The later operation is very
expensive, and AMD-made CPUs do not have self-snooping.
Implement cache flush for remapped region by using clflush for amd64,
when supported by CPU.
Proposed and reviewed by: alc
Approved by: re (kensmith)
the kernel on amd64. Fill and read segment registers for mcontext and
signals. Handle traps caused by restoration of the
invalidated selectors.
Implement user-mode creation and manipulation of the process-specific
LDT descriptors for amd64, see sysarch(2).
Implement support for TSS i/o port access permission bitmap for amd64.
Context-switch LDT and TSS. Do not save and restore segment registers on
the context switch, that is handled by kernel enter/leave trampolines
now. Remove segment restore code from the signal trampolines for
freebsd/amd64, freebsd/ia32 and linux/i386 for the same reason.
Implement amd64-specific compat shims for sysarch.
Linuxolator (temporary ?) switched to use gsbase for thread_area pointer.
TODO:
Currently, gdb is not adapted to show segment registers from struct reg.
Also, no machine-depended ptrace command is added to set segment
registers for debugged process.
In collaboration with: pho
Discussed with: peter
Reviewed by: jhb
Linuxolator tested by: dchagin
Use the method described in IA-32 Intel Architecture Software
Developer's Manual chapter 11.6.6 to get valid mxcsr bits,
use the mxcsr mask to clear invalid bits passed by user code.
via the debug.minidump sysctl and tunable.
Traditional dumps store all physical memory. This was once a good thing
when machines had a maximum of 64M of ram and 1GB of kvm. These days,
machines often have many gigabytes of ram and a smaller amount of kvm.
libkvm+kgdb don't have a way to access physical ram that is not mapped
into kvm at the time of the crash dump, so the extra ram being dumped
is mostly wasted.
Minidumps invert the process. Instead of dumping physical memory in
in order to guarantee that all of kvm's backing is dumped, minidumps
instead dump only memory that is actively mapped into kvm.
amd64 has a direct map region that things like UMA use. Obviously we
cannot dump all of the direct map region because that is effectively
an old style all-physical-memory dump. Instead, introduce a bitmap
and two helper routines (dump_add_page(pa) and dump_drop_page(pa)) that
allow certain critical direct map pages to be included in the dump.
uma_machdep.c's allocator is the intended consumer.
Dumps are a custom format. At the very beginning of the file is a header,
then a copy of the message buffer, then the bitmap of pages present in
the dump, then the final level of the kvm page table trees (2MB mappings
are expanded into a 4K page mappings), then the sparse physical pages
according to the bitmap. libkvm can now conveniently access the kvm
page table entries.
Booting my test 8GB machine, forcing it into ddb and forcing a dump
leads to a 48MB minidump. While this is a best case, I expect minidumps
to be in the 100MB-500MB range. Obviously, never larger than physical
memory of course.
minidumps are on by default. It would want be necessary to turn them off
if it was necessary to debug corrupt kernel page table management as that
would mess up minidumps as well.
Both minidumps and regular dumps are supported on the same machine.
- Add newer CPUID definitions for future use.
Many thanks to Mike Tancsa <mike at sentex dot net> for providing test
cases for Intel Pentium D and AMD Athlon 64 X2.
Approved by: anholt (mentor)
- export the rest of the cpu features (and amd's features).
- turn on EFER_NXE, depending on the NX amd feature bit
- reorg the identcpu stuff a bit in order to stop treating the
amd features as second class features (since it is now a primary feature
bit set) and make it easier to export.
- This is heavily derived from John Baldwin's apic/pci cleanup on i386.
- I have completely rewritten or drastically cleaned up some other parts.
(in particular, bootstrap)
- This is still a WIP. It seems that there are some highly bogus bioses
on nVidia nForce3-150 boards. I can't stress how broken these boards
are. I have a workaround in mind, but right now the Asus SK8N is broken.
The Gigabyte K8NPro (nVidia based) is also mind-numbingly hosed.
- Most of my testing has been with SCHED_ULE. SCHED_4BSD works.
- the apic and acpi components are 'standard'.
- If you have an nVidia nForce3-150 board, you are stuck with 'device
atpic' in addition, because they somehow managed to forget to connect the
8254 timer to the apic, even though its in the same silicon! ARGH!
This directly violates the ACPI spec.
prototypes of cpu_halt(), cpu_reset() and swi_vm() from md_var.h to
cpu.h. This affects db_command.c and kern_shutdown.c.
ia64: move all MD prototypes from cpu.h to md_var.h. This affects
madt.c, interrupt.c and mp_machdep.c. Remove is_physical_memory().
It's not used (vm_machdep.c).
alpha: the MD prototypes have been left in cpu.h with a comment
that they should be there. Moving them is left for later. It was
expected that the impact would be significant enough to be done in
a seperate commit.
powerpc: MD prototypes left in cpu.h. Comment added.
Suggested by: bde
Tested with: make universe (pc98 incomplete)
stolen from the ia64/ia32 code (indeed there was a repocopy), but I've
redone the MD parts and added and fixed a few essential syscalls. It
is sufficient to run i386 binaries like /bin/ls, /usr/bin/id (dynamic)
and p4. The ia64 code has not implemented signal delivery, so I had
to do that.
Before you say it, yes, this does need to go in a common place. But
we're in a freeze at the moment and I didn't want to risk breaking ia64.
I will sort this out after the freeze so that the common code is in a
common place.
On the AMD64 side, this required adding segment selector context switch
support and some other support infrastructure. The %fs/%gs etc code
is hairy because loading %gs will clobber the kernel's current MSR_GSBASE
setting. The segment selectors are not used by the kernel, so they're only
changed at context switch time or when changing modes. This still needs
to be optimized.
Approved by: re (amd64/* blanket)
a heavily stripped down FreeBSD/i386 (brutally stripped down actually) to
attempt to get a stable base to start from. There is a lot missing still.
Worth noting:
- The kernel runs at 1GB in order to cheat with the pmap code. pmap uses
a variation of the PAE code in order to avoid having to worry about 4
levels of page tables yet.
- It boots in 64 bit "long mode" with a tiny trampoline embedded in the
i386 loader. This simplifies locore.s greatly.
- There are still quite a few fragments of i386-specific code that have
not been translated yet, and some that I cheated and wrote dumb C
versions of (bcopy etc).
- It has both int 0x80 for syscalls (but using registers for argument
passing, as is native on the amd64 ABI), and the 'syscall' instruction
for syscalls. int 0x80 preserves all registers, 'syscall' does not.
- I have tried to minimize looking at the NetBSD code, except in a couple
of places (eg: to find which register they use to replace the trashed
%rcx register in the syscall instruction). As a result, there is not a
lot of similarity. I did look at NetBSD a few times while debugging to
get some ideas about what I might have done wrong in my first attempt.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
- Sort definition of cpu_* variables appropriately.
- Move cpu_fxsr out of the magic non-BSS set of variables and stick it in
the BSS along with hw_instruction_sse (make the latter static as well).
Submitted by: bde (partially)
variable to something in the cpu_* namespace since that's what all the
other cpuid variables were named and cpu_procinfo is what I came up with.
Requested by: bde
cpu_exthigh and cpu_brand in printcpuinfo() instead of in identify_cpu().
We also only do it for known-good values of cpu_vendor which is a bit more
conservative.
Reviewed by: bde (mostly)
returned from cpuid 0x80000000.
- Add a cpu_brand char array to hold the processor name returned by
cpuid 0x80000002-0x80000004 on AMD, Intel, Transmeta, and possibly
other CPUs.
- Use cpuid to set cpu_exthigh and read the processor name if it is present
in identify_cpu().
