1) tty.c: gather all the info about the processes before calling ttyprintf
(which may block).
2) syscons.c: handle asynchronous output properly (data structures may
be corrupted otherwise).
Example:
Application use port cua01
Getty open ttyd1 (allocates rawq,outq,etc) and waits while application
done
Application quits, sioclose issued, ttyfree issued (getty calls revoke)
Getty awakes and goes to panic into initrb (NULL rawq)
1) A new mechanism has been added to prevent pages from being paged
out called "vm_page_hold". Similar to vm_page_wire, but
much lower overhead.
2) Scheduling algorithm has been changed to improve interactive
performance.
3) Paging algorithm improved.
4) Some vnode and swap pager bugs fixed.
now HUPCL set only in bidir case for callin lines
(this prevents set HUPCL on mouse)
comhardclose:
in addition to HUPCL case now DTR dropped for bidir case
if line was active in and no carrier present now.
(this prevents DTR sleep on mouse)
Subject: Re: Bugs with floppy drives
Date: Tue, 8 Mar 94 9:11:54 CST
The transfer speed was only set in the retry after error, not when
switching drives.
Eliminates vm_fault overhead on process startup and
mmap referenced data for in-memory pages.
(process startup time using in-memory segments *much* faster)
2) Even more efficient pmap code. Code partially cleaned up.
More comments yet to follow.
(generally more efficient pte management)
3) Pageout clustering ( in addition to the FreeBSD V1.1 pagein
clustering.)
(much faster paging performance on non-write behind disk
subsystems, slightly faster performance on other systems.)
4) Slightly changed vm_pageout code for more efficiency and
better statistics. Also, resist swapout a little more.
(less likely to pageout a recently used page)
5) Slight improvement to the page table page trap efficiency.
(generally faster system VM fault performance)
6) Defer creation of unnamed anonymous regions pager until needed.
(speeds up shared memory bss creation)
7) Remove possible deadlock from swap_pager initialization.
8) Enhanced procfs to provide "vminfo" about vm objects and user
pmaps.
9) Increased MCLSHIFT/MCLBYTES from 2K to 4K to improve net &
socket performance and to prepare for things to come.
John Dyson
dyson@implode.root.com
David Greenman
davidg@root.com
it still looks a little suspicious that so many of the status codes are missing
so I'm not going to adopt all of the existing ones yet. Try to be more
descriptive in the use of hex constants.
Changes _only_ take effect if `options LAPTOP' is set.
Note: This one is distinctly dodgy. When my IDE drive spins back up from sleep
mode, it generates this `extra interrupt' condition by spinning back up and
generating an intr, though without any particular action required. This
message coming out every time is rather annoying, and thus disabled.
However, what I'm not at all sure of is whether or not all IDE drives will
behave in the same way, or if perhaps it needs to be done in a more complicated
fashion by detecting this more involved "I've spun up and am just saying hi"
condition. This is a simple change and easy to back out/ammend if anybody has
any better ideas.
hack in the moment for testing purposes and to get the drive going
again.
0x20 means empty drive.
0x30 means closed drive with CDROM inserted.
0x80 means drive pulled out, but door closed.
0xa0 means drive pulled out and door open.
Luckily none of these values are the same as that reported for Ethernet
cards ( 0 for WD8003E, 0x40 for WD8013EPC, 0x60 for NE2000).
The bad part is, the probe code gets the WD8003E so hosed, that it is
no longer usable after it. No problem with the WD8013EPC.
my previous fix too (using wdp_heads controller value) and check
0 heads case too.
Other fixes from Bruce:
2) Fix dk_timeout from 2 to about 4 seconds.
3) wdcontrol not retried on internal error.
4) wdwait return check changed ( "!=0" to "<0" into wdsetctlr,
"<0" to "!=0" into wdgetctlr).
This inetrface should be used from now on.
pseudo device pty xx still keeps its meaning: a maximum of
xx ptys is allowed.
A ringbuffer is now 2040 bytes long, per Garrett Wollman's request.
The changes are inspired by the way NetBSD did it (thanks for that!),
though I made it slihghtly different, including the interface so
at least 75% of the allocated space is deallocated when the tty is
closed.
Note further that it is easy to modify the ringbuffer length runtime.
This will have to wait untill some later date...
-Guido
This inetrface should be used from now on.
pseudo device pty xx still keeps its meaning: a maximum of
xx ptys is allowed.
A ringbuffer is now 2040 bytes long, per Garrett Wollman's request.
The changes are inspired by the way NetBSD did it (thanks for that!),
though I made it slihghtly different, including the interface so
at least 75% of the allocated space is deallocated when the tty is
closed.
Note further that it is easy to modify the ringbuffer length runtime.
This will have to wait untill some later date...
-Guido
>From: bde@kralizec.zeta.org.au (Bruce Evans)
Subject: cache botch in bootstrap
Date: Sun, 20 Feb 94 18:14:35 +1100
The cache in the bootstrap loader didn't allow for the device changing.
This caused surprisingly little trouble - the cache is only for a single
track (or part of a track), and the first access to a new device is
always for an early sector, so there is no problem unless the last access
to the old device was for an early sector. I saw the problem on a system
with BSD on wd1 and no label on wd0. Everything worked if the the device
name wd(1,a) was specified before the default of wd(0,a) was tried, but
when the default was tried, it failed on the first sector because there
was no label, and then the first sector on wd0 was always used instead
of the first sector on wd1, so there was apparently no label on wd1
either.
Bruce
