the module. Previously we grabbed the mutex used by the callouts,
then stopped the callout with callout_stop, but if the callout
was already active and blocked by the mutex then it would continue
later and reference the mutex after it was destroyed. Instead
stop the callout first then lock.
Supported by: FreeBSD Foundation
o add some more debugging help for figuring out why folks are
getting complaints about releasing routing table entries with
a zero refcnt
o fix comment that talked about spl's
o remove duplicate define of DUMMYNET_DEBUG
Supported by: FreeBSD Foundation
direct dispatch) to avoid extensive kernel stack usage and to
avoid directly re-entering the network stack. The latter causes
locking problems when, for example, a complete TCP handshake`
happens w/o a context switch.
clobbers this variable. Long ago, when the idle loop wasn't in a
process, it set switchtime.tv_sec to zero to indicate that the time
needs to be read after the idle loop finishes. The special case for
this isn't needed now that there is an idle process (for each CPU).
The time is read in the normal way when the idle process is switched
away from. The seconds component of the time is only zero for the
first second after the uptime is set, and the mostly-dead code was only
executed during this time. (This was slightly broken by using uptimes
instead of times relative to the Epoch -- in the original version the
seconds component of the time was only 0 for the first second after
the Epoch.)
In mi_switch(), moved the setting of switchticks to just after the
first (and now only) setting of switchtime. This setting used to be
delayed since a late setting was needed for the idle case and an early
setting was not needed. Now the early setting is needed so that
fork_exit() doesn't need to set either switchtime or switchticks.
Removed now-completely-rotted comment attached to this. Most of the
code described by the comment had already moved to sched_switch().
very first cell in the mbuf should have a cell header word (of which
everything except the payload type and the CLP bit is ignored). All
other cells should be 48 byte and get the same header as the first cell.
This fixes a problem with sending more than 120000 raw cells/sec through
an HE155. The card seems to need 2 cell times to DMA the transmit buffer
ready queue entry and the transmit buffer descriptor so at 1/3 the
link rate the transmit buffer ready queue starts to fill up. Even with this
patch it's obviously impossible to send raw cells at link rate.
- implement the tunnel egress rule in ip_ecn_egress() in ip_ecn.c.
make ip{,6}_ecn_egress() return integer to tell the caller that
this packet should be dropped.
- handle ECN at fragment reassembly in ip_input.c and frag6.c.
Obtained from: KAME
begin with sched_lock held but not recursed, so this variable was
always 0.
Removed fixup of sched_lock.mtx_recurse after context switches in
sched_switch(). Context switches always end with this variable in the
same state that it began in, so there is no need to fix it up. Only
sched_lock.mtx_lock really needs a fixup.
Replaced fixup of sched_lock.mtx_recurse in fork_exit() by an assertion
that sched_lock is owned and not recursed after it is fixed up. This
assertion much match the one in mi_switch(), and if sched_lock were
recursed then a non-null fixup of sched_lock.mtx_recurse would probably
be needed again, unlike in sched_switch(), since fork_exit() doesn't
return to its caller in the normal way.
Correct a bug when the number of pages for external mbufs was
very large. In this case the page number could overflow into the large
buffer flag. Make this more unlikley by move that flag further away.
This enable us to use /dev/fwmem* as a core file.
e.g.
ps -M /dev/fwmem0.0 -N kernel.debug
dmesg -M /dev/fwmem0.0 -N kernel.debug
gdb -k -c /dev/fwmem0.0 kernel.debug
You need to set target EUI64 in hw.firewire.fwmem.eui64_hi/lo before
opening the device. On the target arch, (PCI) bus address must be
equivalent to physical address.
(We cannot use this for sparc64 because of IOMMU.)
No objection in: -audit
is returned from the card to the driver. Add a counter that shows
how many times this allocation has failed. Note, that we could even
further delay the allocation of the mbuf until we know, that we need it
(there are no receive errors and the connection is open). This will be done
in a later commit.
Print the new statistics field in atmconfig.
atomic instructions instead. Remove the stuff used to track
whether an external mbuf travels through the system. This is
temporary only and will come back soon.
code has the typical branch prediction detour, which creates cross-
section branches. A LINT kernel is apparently large enough nowadays
that the .text and .text2 sections cannot always be layed-out so that
branches between them reach.
The fix is to stop using the alpha-specific bitops and instead use
the portable implementation used by all platforms other than alpha
and i386.