- Destroy mutex in case of attach failure. [1]
- Lock properly em_watchdog(). [1]
- Lock properly em_sysctl_int_delay(). [1]
- Remove unused global adapter linked list.
- Remove unused dma_size field from struct em_dma_alloc.
- Do not touch interface statistics, that must be edited
only by upper layers. [1]
Submitted by: yongari [1]
o Do not mask the RX overrun interrupt.
o Rewrite em_intr():
- Axe EM_MAX_INTR.
- Cycle acknowledging interrupts and processing
packets until zero interrupt cause register is
read.
- If RX overrun comes in log this fact. [ NetBSD also
resets adapter in this case, but my tests showed that
this is not needed and only pessimizes behavior under
heavy load. ]
- Since almost all functions is rewritten, style the
remaining lines.
This fixes em(4) interfaces wedging under high load.
In collaboration with: wpaul, cognet
Obtained from: NetBSD
flag. This fixes panic, when 'ifconfig em0 down' was called and it calls
em_stop() while the em_process_receive_interrupts() has temporarily
dropped the lock.
sampling rate:
- Improve vchan chn_setspeed() strategy. Try to avoid FEEDER_RATE
on parent channel if the requested value is not supported
by the hardware.
- Fix vchan default speed calculation. In any case, vchan should
rely on parent bufsoft speed instead of bufhard since it is
possible that the entire feeder chain might involve FEEDER_RATE.
This is possible under extreme, rare condition if the above
chn_setspeed() strategy failed.
Approved by: netchild (mentor)
- Change ndis_return() from a DPC to a workitem so that it doesn't
run at DISPATCH_LEVEL (with the dispatcher lock held).
- In if_ndis.c, submit packets to the stack via (*ifp->if_input)() in
a workitem instead of doing it directly in ndis_rxeof(), because
ndis_rxeof() runs in a DPC, and hence at DISPATCH_LEVEL. This
implies that the 'dispatch level' mutex for the current CPU is
being held, and we don't want to call if_input while holding
any locks.
- Reimplement IoConnectInterrupt()/IoDisconnectInterrupt(). The original
approach I used to track down the interrupt resource (by scanning
the device tree starting at the nexus) is prone to problems when
two devices share an interrupt. (E.g removing ndis1 might disable
interrupts for ndis0.) The new approach is to multiplex all the
NDIS interrupts through a common internal dispatcher (ntoskrnl_intr())
and allow IoConnectInterrupt()/IoDisconnectInterrupt() to add or
remove interrupts from the dispatch list.
- Implement KeAcquireInterruptSpinLock() and KeReleaseInterruptSpinLock().
- Change the DPC and workitem threads to use the KeXXXSpinLock
API instead of mtx_lock_spin()/mtx_unlock_spin().
- Simplify the NdisXXXPacket routines by creating an actual
packet pool structure and using the InterlockedSList routines
to manage the packet queue.
- Only honor the value returned by OID_GEN_MAXIMUM_SEND_PACKETS
for serialized drivers. For deserialized drivers, we now create
a packet array of 64 entries. (The Microsoft DDK documentation
says that for deserialized miniports, OID_GEN_MAXIMUM_SEND_PACKETS
is ignored, and the driver for the Marvell 8335 chip, which is
a deserialized miniport, returns 1 when queried.)
- Clean up timer handling in subr_ntoskrnl.
- Add the following conditional debugging code:
NTOSKRNL_DEBUG_TIMERS - add debugging and stats for timers
NDIS_DEBUG_PACKETS - add extra sanity checking for NdisXXXPacket API
NTOSKRNL_DEBUG_SPINLOCKS - add test for spinning too long
- In kern_ndis.c, always start the HAL first and shut it down last,
since Windows spinlocks depend on it. Ntoskrnl should similarly be
started second and shut down next to last.
the descriptors set.
- In em_process_receive_interrupts(), call bus_dmamap_sync() for the
descriptors set each time we modify one descriptor, instead of doing it only
at the function exit, to make sure the adapters know he can re-use the
descriptor.
This helps on arm with write-back data cache (and possibly on other arches
with bounce pages, I don't know) under heavy network load. Without this,
if we attempt to process more than num_rx_desc descriptors, the adapter
would just stop processing rx interrupts.
the former is the ISA part, not the latter.
MFC After 6.0 is unfrozen (this bug doesn't exist in 6.0 because I didn't
MFC the rtl80x9 changes for ISA due to an error on my part)
to the 100/1000 BCM5400 phy. This fixes the problem with
the GEM port not syncing up on Sawtooth G4's.
Obtained from: NetBSD
Reported by: Ben Rosengart <ben + freebsd org at narcissus net>
cards and teach the re(4) driver to attach to revision 3 cards.
Submitted by: Fredrik Lindberg fli+freebsd-current at shapeshifter dot se
MFC after: 2 weeks
Reviewed by: imp, mdodd
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
do not support the GETINFO immediate command, unlike just about every other
variant of the hardware. Also document some magic values and fix some minor
nearby whitespace.
MFC After: 3 days
The receive function em_process_receive_interrupts() unlocks the
adapter while ether_input() processes the packet, and then locks
it back. In the meantime, em_init() may be called, either from
em_watchdog() from softclock interrupt or from the ifconfig(8)
program. The em_init() resets the card, in particular it sets
adapter->next_rx_desc_to_check to 0 and resets hardware RX Head
and Tail descriptor pointers. The loop in
em_process_receive_interrupts() does not expect these things to
change, and a mess may result.
This fixes long wedges of em(4) interfaces receive part under high
load and IP fastforwarding enabled.
PR: kern/87418
Submitted by: Dmitrij Tejblum <tejblum yandex-team.ru>
the ExCA spec, and close cousins:
o Write an activate routine that works.
o merge a couple of items from oldcard before they are lost
o write a deactivate routine
I suspect we're still a ways away from having this work, but maybe for
6.1/5.5?
as a Novell NE-2000. This is necessary for unpatched qemu working
correctly. qemu claims to be a RTL8029, but doesn't implement the
RTL8029 specific registers at this time. I've created patches for
that, but there's no reason we can't use qemu's emulation w/o these
patches. This should make life easier for those folks that boot
FreeBSD via qemu.
ed_probe_generic8390 where we're calling it. It will be done as part
of ed_probe_Novel_generic after things are setup in a way that
ed_probe_generic8390 will grok.
o Fix operator precedence botch that causes a panic when setting the media
type for 10baseT connections.
o Save the type of device so that it prints with the rest of the probe.
# this should make it work with qemu again, but only if it has my patches
# to actually implement the RTL8029 specific registers.
- Use device_printf() and if_printf() and remove nge_unit.
- Use callout_init_mtx() and remove nge_tick_locked() as nge_tick() is now
always called with the driver lock held.
- Use M_ZERO to contigmalloc() when allocating nge_ldata. It was possible
for the random garbage to be used in certain cases otherwise.
- Cleanup attach error handling including no longer leaking nge_ldata.
- Add locking to the ifmedia callouts.
- Lock accesses to if_hwassist and if_capenable in nge_ioctl().
Submitted by: Yuriy N. Shkandybin jura at networks dot ru (1, 3, 4)
Tested by: Yuriy N. Shkandybin jura at networks dot ru
MFC after: 3 days
based on XMAC II chip should be ready for this in their initial
mode of operation, and Yukon-based NICs are configured so by
the driver.
PR: kern/79998
MFC after: 1 month
generic sounding CIS "PCMCIA", "FAST ETHERENT CARD" and a bogus MANFID
code (0xffff and 0x1090). However, since I'm not aware of 'generic'
cards that aren't NE-2000oids, go with that and hope for the best.
First and most importantly, I threw out the thread priority-twiddling
implementation of KeRaiseIrql()/KeLowerIrq()/KeGetCurrentIrql() in
favor of a new scheme that uses sleep mutexes. The old scheme was
really very naughty and sought to provide the same behavior as
Windows spinlocks (i.e. blocking pre-emption) but in a way that
wouldn't raise the ire of WITNESS. The new scheme represents
'DISPATCH_LEVEL' as the acquisition of a per-cpu sleep mutex. If
a thread on cpu0 acquires the 'dispatcher mutex,' it will block
any other thread on the same processor that tries to acquire it,
in effect only allowing one thread on the processor to be at
'DISPATCH_LEVEL' at any given time. It can then do the 'atomic sit
and spin' routine on the spinlock variable itself. If a thread on
cpu1 wants to acquire the same spinlock, it acquires the 'dispatcher
mutex' for cpu1 and then it too does an atomic sit and spin to try
acquiring the spinlock.
Unlike real spinlocks, this does not disable pre-emption of all
threads on the CPU, but it does put any threads involved with
the NDISulator to sleep, which is just as good for our purposes.
This means I can now play nice with WITNESS, and I can safely do
things like call malloc() when I'm at 'DISPATCH_LEVEL,' which
you're allowed to do in Windows.
Next, I completely re-wrote most of the event/timer/mutex handling
and wait code. KeWaitForSingleObject() and KeWaitForMultipleObjects()
have been re-written to use condition variables instead of msleep().
This allows us to use the Windows convention whereby thread A can
tell thread B "wake up with a boosted priority." (With msleep(), you
instead have thread B saying "when I get woken up, I'll use this
priority here," and thread A can't tell it to do otherwise.) The
new KeWaitForMultipleObjects() has been better tested and better
duplicates the semantics of its Windows counterpart.
I also overhauled the IoQueueWorkItem() API and underlying code.
Like KeInsertQueueDpc(), IoQueueWorkItem() must insure that the
same work item isn't put on the queue twice. ExQueueWorkItem(),
which in my implementation is built on top of IoQueueWorkItem(),
was also modified to perform a similar test.
I renamed the doubly-linked list macros to give them the same names
as their Windows counterparts and fixed RemoveListTail() and
RemoveListHead() so they properly return the removed item.
I also corrected the list handling code in ntoskrnl_dpc_thread()
and ntoskrnl_workitem_thread(). I realized that the original logic
did not correctly handle the case where a DPC callout tries to
queue up another DPC. It works correctly now.
I implemented IoConnectInterrupt() and IoDisconnectInterrupt() and
modified NdisMRegisterInterrupt() and NdisMDisconnectInterrupt() to
use them. I also tried to duplicate the interrupt handling scheme
used in Windows. The interrupt handling is now internal to ndis.ko,
and the ndis_intr() function has been removed from if_ndis.c. (In
the USB case, interrupt handling isn't needed in if_ndis.c anyway.)
NdisMSleep() has been rewritten to use a KeWaitForSingleObject()
and a KeTimer, which is how it works in Windows. (This is mainly
to insure that the NDISulator uses the KeTimer API so I can spot
any problems with it that may arise.)
KeCancelTimer() has been changed so that it only cancels timers, and
does not attempt to cancel a DPC if the timer managed to fire and
queue one up before KeCancelTimer() was called. The Windows DDK
documentation seems to imply that KeCantelTimer() will also call
KeRemoveQueueDpc() if necessary, but it really doesn't.
The KeTimer implementation has been rewritten to use the callout API
directly instead of timeout()/untimeout(). I still cheat a little in
that I have to manage my own small callout timer wheel, but the timer
code works more smoothly now. I discovered a race condition using
timeout()/untimeout() with periodic timers where untimeout() fails
to actually cancel a timer. I don't quite understand where the race
is, using callout_init()/callout_reset()/callout_stop() directly
seems to fix it.
I also discovered and fixed a bug in winx32_wrap.S related to
translating _stdcall calls. There are a couple of routines
(i.e. the 64-bit arithmetic intrinsics in subr_ntoskrnl) that
return 64-bit quantities. On the x86 arch, 64-bit values are
returned in the %eax and %edx registers. However, it happens
that the ctxsw_utow() routine uses %edx as a scratch register,
and x86_stdcall_wrap() and x86_stdcall_call() were only preserving
%eax before branching to ctxsw_utow(). This means %edx was getting
clobbered in some cases. Curiously, the most noticeable effect of this
bug is that the driver for the TI AXC110 chipset would constantly drop
and reacquire its link for no apparent reason. Both %eax and %edx
are preserved on the stack now. The _fastcall and _regparm
wrappers already handled everything correctly.
I changed if_ndis to use IoAllocateWorkItem() and IoQueueWorkItem()
instead of the NdisScheduleWorkItem() API. This is to avoid possible
deadlocks with any drivers that use NdisScheduleWorkItem() themselves.
The unicode/ansi conversion handling code has been cleaned up. The
internal routines have been moved to subr_ntoskrnl and the
RtlXXX routines have been exported so that subr_ndis can call them.
This removes the incestuous relationship between the two modules
regarding this code and fixes the implementation so that it honors
the 'maxlen' fields correctly. (Previously it was possible for
NdisUnicodeStringToAnsiString() to possibly clobber memory it didn't
own, which was causing many mysterious crashes in the Marvell 8335
driver.)
The registry handling code (NdisOpen/Close/ReadConfiguration()) has
been fixed to allocate memory for all the parameters it hands out to
callers and delete whem when NdisCloseConfiguration() is called.
(Previously, it would secretly use a single static buffer.)
I also substantially updated if_ndis so that the source can now be
built on FreeBSD 7, 6 and 5 without any changes. On FreeBSD 5, only
WEP support is enabled. On FreeBSD 6 and 7, WPA-PSK support is enabled.
The original WPA code has been updated to fit in more cleanly with
the net80211 API, and to eleminate the use of magic numbers. The
ndis_80211_setstate() routine now sets a default authmode of OPEN
and initializes the RTS threshold and fragmentation threshold.
The WPA routines were changed so that the authentication mode is
always set first, followed by the cipher. Some drivers depend on
the operations being performed in this order.
I also added passthrough ioctls that allow application code to
directly call the MiniportSetInformation()/MiniportQueryInformation()
methods via ndis_set_info() and ndis_get_info(). The ndis_linksts()
routine also caches the last 4 events signalled by the driver via
NdisMIndicateStatus(), and they can be queried by an application via
a separate ioctl. This is done to allow wpa_supplicant to directly
program the various crypto and key management options in the driver,
allowing things like WPA2 support to work.
Whew.
routine, create all the child bio objects before starting the
requests, rather than starting them as created. This closes a race
whereby some number of child operations could complete before the
rest were ever created, and prematurely freeing the parent bio.
This fixes the panics installing in VMWare and qemu
