'be_destroy' can destroy a boot environment (by name) or a given snapshot.
If the target to be destroyed is a dataset, check if it's mounted. We don't
want to check if the origin dataset is mounted when destroying a snapshot.
PR: 236043
Submitted by: Rob Fairbanks <rob.fx907 gmail com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19650
providers mediasize changes.
While here, use GEOM nomenclature to describe providers instead of calling
them device nodes.
Obtained from: Fudo Security
Tested in: AWS
Direct /etc/rc exec was introduced in r337321, with a fallback to
passing it to sh if direct exec fails. "Can't exec" is slightly
misleading in this case (the script is still executed, just not
directly).
HGST was bought by WDC. Over the years, it has sold different drives
branded as HGST, WD or WDC. All of them need the HGST workaround of
sending 4k-sized packets (or multiples of 4k). And the ones that don't
really need this aren't broken by this change. Submitter is the vendor
who has tested these changes on a number of drives. I've simplified it
slightly, since we don't need additional vendors for this at this
time.
Submitted by: JacobBurley via github on behalf of WDC
Pull Request: https://github.com/freebsd/freebsd/pull/391
This makes it more consistent with other filesystems, which all end in "fs",
and more consistent with its mount helper, which is already named
"mount_fusefs".
Reviewed by: cem, rgrimes
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19649
The jail(8) command provides a variety of jail pseudo-parameters that are
useful to consumers of bectl, mount.devfs being the most-often-requested
paramater by bectl users.
command, exec.start, nopersist, and persist may not be specified via -o to
bectl. The command/exec.start remains passed as it always has at the end of
bectl, and persistence is dictated by -b/-U bectl jail arguments.
Submitted by: Wes Maag <jwmaag gmail com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19282
Update NAT64LSN implementation:
o most of data structures and relations were modified to be able support
large number of translation states. Now each supported protocol can
use full ports range. Ports groups now are belongs to IPv4 alias
addresses, not hosts. Each ports group can keep several states chunks.
This is controlled with new `states_chunks` config option. States
chunks allow to have several translation states for single alias address
and port, but for different destination addresses.
o by default all hash tables now use jenkins hash.
o ConcurrencyKit and epoch(9) is used to make NAT64LSN lockless on fast path.
o one NAT64LSN instance now can be used to handle several IPv6 prefixes,
special prefix "::" value should be used for this purpose when instance
is created.
o due to modified internal data structures relations, the socket opcode
that does states listing was changed.
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
o most of data structures and relations were modified to be able support
large number of translation states. Now each supported protocol can
use full ports range. Ports groups now are belongs to IPv4 alias
addresses, not hosts. Each ports group can keep several states chunks.
This is controlled with new `states_chunks` config option. States
chunks allow to have several translation states for single alias address
and port, but for different destination addresses.
o by default all hash tables now use jenkins hash.
o ConcurrencyKit and epoch(9) is used to make NAT64LSN lockless on fast path.
o one NAT64LSN instance now can be used to handle several IPv6 prefixes,
special prefix "::" value should be used for this purpose when instance
is created.
o due to modified internal data structures relations, the socket opcode
that does states listing was changed.
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
CLAT is customer-side translator that algorithmically translates 1:1
private IPv4 addresses to global IPv6 addresses, and vice versa.
It is implemented as part of ipfw_nat64 kernel module. When module
is loaded or compiled into the kernel, it registers "nat64clat" external
action. External action named instance can be created using `create`
command and then used in ipfw rules. The create command accepts two
IPv6 prefixes `plat_prefix` and `clat_prefix`. If plat_prefix is ommitted,
IPv6 NAT64 Well-Known prefix 64:ff9b::/96 will be used.
# ipfw nat64clat CLAT create clat_prefix SRC_PFX plat_prefix DST_PFX
# ipfw add nat64clat CLAT ip4 from IPv4_PFX to any out
# ipfw add nat64clat CLAT ip6 from DST_PFX to SRC_PFX in
Obtained from: Yandex LLC
Submitted by: Boris N. Lytochkin
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Add second IPv6 prefix to generic config structure and rename another
fields to conform to RFC6877. Now it contains two prefixes and length:
PLAT is provider-side translator that translates N:1 global IPv6 addresses
to global IPv4 addresses. CLAT is customer-side translator (XLAT) that
algorithmically translates 1:1 IPv4 addresses to global IPv6 addresses.
Use PLAT prefix in stateless (nat64stl) and stateful (nat64lsn)
translators.
Modify nat64_extract_ip4() and nat64_embed_ip4() functions to accept
prefix length and use plat_plen to specify prefix length.
Retire net.inet.ip.fw.nat64_allow_private sysctl variable.
Add NAT64_ALLOW_PRIVATE flag and use "allow_private" config option to
configure this ability separately for each NAT64 instance.
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
The -l flag sends only the READ CAPACITY (16) sevice action. Normally
we send the READ CAPACITY (10) command, and only send RC16 when the
capacity is larger than 2TB (since that's the max RC10 can
report). However, some badly programmed drives report different
numbers for RC10 and RC16. This can be hard to diagnose, but generally
there's a "Logical block address out of range" error when RC16 reports
a larger number than RC10 and the RC10 number is the correct one. By
comparing the output of readcap with and without the -l argmuent, one
can determine if there's a mismatch and if the DA_Q_NO_RC16 quirk is
needed.
Reviewed by: ken@
Differential Revision: https://reviews.freebsd.org/D19536
All changes are hidden behind the EXPERIMENTAL option and are not compiled
in by default.
Add ND6_IFF_IPV6_ONLY_MANUAL to be able to set the interface into no-IPv4-mode
manually without router advertisement options. This will allow developers to
test software for the appropriate behaviour even on dual-stack networks or
IPv6-Only networks without the option being set in RA messages.
Update ifconfig to allow setting and displaying the flag.
Update the checks for the filters to check for either the automatic or the manual
flag to be set. Add REVARP to the list of filtered IPv4-related protocols and add
an input filter similar to the output filter.
Add a check, when receiving the IPv6-Only RA flag to see if the receiving
interface has any IPv4 configured. If it does, ignore the IPv6-Only flag.
Add a per-VNET global sysctl, which is on by default, to not process the automatic
RA IPv6-Only flag. This way an administrator (if this is compiled in) has control
over the behaviour in case the node still relies on IPv4.
The change removes SIOC[GS]IEEE80211 handling from ifconfig(8)
if WITHOUT_WIRELESS_SUPPORT=yes is set in src.conf(5).
Reviewed by: bz
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19289
inodes that reference directories. While here tighten the check for
comparing the last logical block with the end of the file.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: Netflix
filesystem block size. When a size is specified with the -S flag
to tunefs(8), round it up to the filesystem block size.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: Netflix
Eliminate trailing whitespace on inet, inet6, and groups lines. I think the
"list txpower" command will still show some, but I'm not able to test that.
PR: 153731
Reported-by: Nikolay Denev <ndenev@gmail.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19004
shorter than its size resulting in a hole as its final block (which
is a violation of the invarients of the UFS filesystem).
Soft updates will always ensure that the file size is correct when
writing inodes to disk for files that contain only direct block
pointers. However soft updates does not roll back sizes for files
with indirect blocks that it has set to unallocated because their
contents have not yet been written to disk. Hence, the file can
appear to have a hole at its end because the block pointer has been
rolled back to zero when its inode was written to disk. Thus,
fsck_ffs calculates the last allocated block in the file. For files
that extend into indirect blocks, fsck_ffs checks for a size past
the last allocated block of the file and if that is found, shortens
the file to reference the last allocated block thus avoiding having
it reference a hole at its end.
Submitted by: Chuck Silvers <chs@netflix.com>
Tested by: Chuck Silvers <chs@netflix.com>
MFC after: 1 week
Sponsored by: Netflix
A big security advantage of Wayland is not allowing applications to read
input devices all the time. Having /dev/input/* accessible to the user
account subverts this advantage.
libudev-devd was opening the evdev devices to detect their types (mouse,
keyboard, touchpad, etc). This don't work if /dev/input/* is inaccessible.
With the kernel exposing this information as sysctls (kern.evdev.input.*),
we can work w/o /dev/input/* access, preserving the Wayland security model.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: wulf, imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18694
MTU if we've set it once and there were no changes on the DHCP server
side since the last refresh. This is consistent I believe with how dhclient
handles other settings like IP address, mask etc.
Approved by: cem, eugen
Differential Revision: https://reviews.freebsd.org/D18546
Move from using a linker set to a constructor function that's
called. This simplifies the code and is slightly more obvious. We now
keep a list of page decoders rather than having an array we managed
before. Commands will move to something similar in the future.
Reviewed by: jhb@
Differential Revision: https://reviews.freebsd.org/D19275
pass of fsck_ffs. Some changes, such as check-hash corrections were
being lost.
Reported by: Michael Tuexen (tuexen@)
Tested by: Michael Tuexen (tuexen@)
MFC after: 3 days
Mentioned in mdconfig(8), malloc-backed md(4) can be unstable unless
required memory is allocated up front with -o reserve. Furthermore, panics
have been observed with md used in fstab on 12.0-RELEASE. Choose the stable
route and pass -o reserve.
Submitted by: Paul Vixie
MFC after: 1 week
Set up zpools with a more unique name, stash the zpool name away in a file pointed
to by `$ZPOOL_NAME_FILE` (which is relative to a per-testcase generated temporary
directory), then remove the file based on `$ZPOOL_NAME_FILE` in the cleanup
routines.
This is a more concurrency-safe solution and will allow the testcases to be safely
executed in parallel.
Reviewed by: kevans, jtl
Approved by: jtl (mentor)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19024
The logic added in r343287 to avoid false-positive
sum-of-child-bandwidth check errors for HFSC queues has a bug in it
that causes the upperlimit service curve of an HFSC queue to be pulled
down to its parent's linkshare service curve if it happens to be above
it.
Upon further inspection/reflection, this generic
sum-of-child-bandwidths check does not need to be fixed for HFSC - it
needs to be skipped. For HFSC, the equivalent check is to ensure the
sum of child linkshare service curves are at or below the parent's
linkshare service curve, and this check is already being performed by
eval_pfqueue_hfsc().
This commit reverts the affected parts of r343287 and adds new logic
to skip the generic sum-of-child-bandwidths check for HFSC.
MFC after: 1 day
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D19124
This code allocated a correctly sized buffer, read past the end of the
source buffer, writing off the end of the target buffer, and then writing
a '\0' terminator past the end of the target buffer (in the wrong place).
It then leaked the buffer.
Switch to a statically sized buffer on the stack and update the source
pointer and
length before use so the correct things are copied.
Fix a logic error in the checks that the format of the line is as
expected and move on out of an assert.
Remove an unneeded close(). fclose() closes the descriptor.
Found with: CheriABI
Obtained from: CheriBSD
Reviewed by: kib, jhb, markj
Differential Revision: https://reviews.freebsd.org/D19122
We can't predict when destruction of origin is needed, and currently we have
a precedent for not prompting for things. Leave the decision up to the user
of bectl(8) if they want the origin snapshot to be destroyed or not.
Emits a warning when -o isn't used and an origin snapshot is left to be
cleaned up, for the time being. This is handy when one drops the -o flag but
really did want to clean up the origin.
A couple of -e ignore's have been sprinkled around the test suite for places
that we don't care that the origin's not been cleaned up. -o functionality
tests will be added in the future, but are omitted for now to reduce
conflicts with work in flight to fix bits of the tests.
Reported by: Shawn Webb
MFC after: 1 week
Setting the length of the request got lost in r343287, which means SIOCGIFGMEMB
gives us the required length, but does not copy the names of the group members.
As a result we don't get a correct list of group members, and 'set skip on
<ifgroup>' broke.
This produced all sorts of very unexpected results, because we would end up
applying 'set skip' to unexpected interfaces.
X-MFC-with: r343287
r343896 made it such that a non-zero exit status was passed through, but was
still wrong if the script exits on a signal. POSIX does not say what the
WEXITSTATUS macro returns in this case and in practice 0 is a common value.
Instead, translate the wait status into 8 bits the same way as the shell
calculates $?.
Reviewed by: kib, Nash Kaminski
MFC after: 1 week
This is also OpenBSD rev. 1.117, as pointed out by
Ryan Moeller <ryan@ixsystems.com>.
Submitted by: Nash Kaminski <nashkaminski@gmail.com>
MFC after: 1 week
Properly pass down is_all to table_show_list(). This restores the behavior
before r272840 so that only 'ipfw table all list' shows the headers.
MFC after: 2 weeks
Relnotes: yes
Use recent best practices for Copyright form at the top of
the license:
1. Remove all the All Rights Reserved clauses on our stuff. Where we
piggybacked others, use a separate line to make things clear.
2. Use "Netflix, Inc." everywhere.
3. Use a single line for the copyright for grep friendliness.
4. Use date ranges in all places for our stuff.
Approved by: Netflix Legal (who gave me the form), adrian@ (pmc files)
For 11n / 11ac we are still using non-11n rates for management and
multicast traffic by default; check 'MCS rate' bit to determine how
to print them correctly.
PR: 161035
MFC after: 1 week
The KPI have been reviewed and cleansed of features that were planned
back 20 years ago and never implemented. The pfil(9) internals have
been made opaque to protocols with only returned types and function
declarations exposed. The KPI is made more strict, but at the same time
more extensible, as kernel uses same command structures that userland
ioctl uses.
In nutshell [KA]PI is about declaring filtering points, declaring
filters and linking and unlinking them together.
New [KA]PI makes it possible to reconfigure pfil(9) configuration:
change order of hooks, rehook filter from one filtering point to a
different one, disconnect a hook on output leaving it on input only,
prepend/append a filter to existing list of filters.
Now it possible for a single packet filter to provide multiple rulesets
that may be linked to different points. Think of per-interface ACLs in
Cisco or Juniper. None of existing packet filters yet support that,
however limited usage is already possible, e.g. default ruleset can
be moved to single interface, as soon as interface would pride their
filtering points.
Another future feature is possiblity to create pfil heads, that provide
not an mbuf pointer but just a memory pointer with length. That would
allow filtering at very early stages of a packet lifecycle, e.g. when
packet has just been received by a NIC and no mbuf was yet allocated.
Differential Revision: https://reviews.freebsd.org/D18951
This is a wild guess as to why bectl tests failed once upon a time in CI,
given no apparent way to see a transcript of cleanup routines with Kyua. The
bectl tests construct a new, clean zpool for every test. The failure
indicated was because of a mount that was leftover from a previous test, but
the previous test had succeeded so it's not clear how the mount remained
leftover unless the `zpool get health ${pool}` had somehow failed.
MFC after: 1 week
When performing a non-status operation on a single interface, it is
not necessary for ifconfig to build a list of all addresses in the
system, sort them, then iterate through them looking for the entry for
the single interface of interest. Doing so becomes increasingly
expensive as the number of interfaces in the system grows (e.g., in a
system with 1000+ vlan(4) interfaces).
Reviewed by: ae, kp
MFC after: 1 week
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D18919
The kernel will reject very large tables to avoid resource exhaustion
attacks. Some users run into this limit with legitimate table
configurations.
The error message in this case was not very clear:
pf.conf:1: cannot define table nets: Invalid argument
pfctl: Syntax error in config file: pf rules not loaded
If a table definition fails we now check the request_maxcount sysctl,
and if we've tried to create more than that point the user at
net.pf.request_maxcount:
pf.conf:1: cannot define table nets: too many elements.
Consider increasing net.pf.request_maxcount.
pfctl: Syntax error in config file: pf rules not loaded
PR: 235076
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18909
to make it consistent with newfs. Document the legality of '_'
in label names in both tunefs(8) and newfs(8).
PR: 235182
Submitted by: darius@dons.net.au
Reviewed by: Conrad Meyer
MFC after: 3 days
Sponsored by: Netflix
The number of syscalls made during parsing of any config that
defines tables is also reduced, and incorrect warnings that HFSC
parent queue bandwidths were smaller than the sum of their child
bandwidths have been fixed.
Reviewed by: kp
MFC after: 1 week
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D18759
Do not invoke 'wlan_up' function from devd(8) on interface
creation event (an example to create such event:
'ifconfig wlan0 create wlandev rtwn0');
they're typically produced during 'service netif (re)start'
and result in duplicate interface initialization.
From the user side if WPA option is used, this result in messages like:
- /etc/rc.d/wpa_supplicant: WARNING: failed to start wpa_supplicant
or
- wpa_supplicant already running? (pid=xxxx).
(for HOSTAP interfaces this race may result in startup failure).
As a side effect, wpa_supplicant(8) / hostapd(8) will not be
invoked when new wlan(4) interface is created manually and
corresponding configuration for it is present in rc.conf(5).
This change does not affect device attach / removal events.
MFC after: 5 days
When we skip on a group the kernel will automatically skip on the member
interfaces. We still need to update our own cache though, or we risk
overruling the kernel afterwards.
This manifested as 'set skip' working initially, then not working when
the rules were reloaded.
PR: 229241
MFC after: 1 week
This set of changes is geared towards making bectl respect deep boot
environments when they exist and are mounted. The deep BE composition
functionality (`bectl add`) remains disabled for the time being. This set of
changes has no effect for the average user. but allows deep BE users to
upgrade properly with their current setup.
libbe(3): Open the target boot environment and get a zfs handle, then pass
that with the target mountpoint to be_mount_iter; If the BE_MNT_DEEP flag is
set call zfs_iter_filesystems and mount the child datasets.
Similar logic is employed when unmounting the datasets, save for children
are unmounted first.
bectl(8): Change bectl_cmd_jail to pass the BE_MNT_DEEP flag when
calling be_mount as well as call be_unmount when cleaning up after the
jail has exited instead of umount(2) directly.
PR: 234795
Submitted by: Wes Maag <jwmaag_gmail.com> (test additions by kevans)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18796
Try to reword -prefixlen section to more clearly and accurately describe how
the -prefixlen modifier works.
While here, fix a word that igor considered a typo: aggregatable addresses is a
valid technical term per RFC-2374, however, it was superseded by the term
"aggregator" in RFC-3587.
MFC after: 1 week
Reviewed by: 0mp, crees
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D10087
These programs parse ND6 Router Advertisement messages; rtsold(8) has
required an SA, SA-14:20.rtsold, for a bug in this code. Thus, they
are good candidates for sandboxing.
The approach taken is to run the main executable in capability mode
and use Casper services to provide functionality that cannot be
implemented within the sandbox. In particular, several custom services
were required.
- A Casper service is used to send Router Solicitation messages on a
raw ICMP6 socket. Initially I took the approach of creating a
socket for each interface upon startup, and connect(2)ing it to
the all-routers multicast group for the interface. This permits
the use of sendmsg(2) in capability mode, but only works if the
interface's link is up when rtsol(d) starts. So, instead, the
rtsold.sendmsg service is used to transmit RS messages on behalf
of the main process. One could alternately define a service
which simply creates and connects a socket for each destination
address, and returns the socket to the sandboxed process. However,
to implement rtsold's -m option we also need to read the ND6 default
router list, and this cannot be done in capability mode.
- rtsold may execute resolvconf(8) in response to RDNSS and DNSSL
options in received RA messages. A Casper service is used to
fork and exec resolvconf(8), and to reap the child process.
- A service is used to determine whether a given interface's
link-local address is useable (i.e., not duplicated or undergoing
DAD). This information is supplied by getifaddrs(3), which reads
a sysctl not available in capability mode. The SIOCGIFCONF socket
ioctl provides equivalent information and can be used in capability
mode, but I decided against it for now because of some limitations
of that interface.
In addition to these new services, cap_syslog(3) is used to send
messages to syslogd.
Reviewed by: oshogbo
Tested by: bz (previous versions)
MFC after: 2 months
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17572
This follows the example of other Capsicumized programs in /sbin.
Reported by: Manfred Antar <manfredantar@gmail.com>
MFC with: r342699
Sponsored by: The FreeBSD Foundation
- Use cap_fileargs(3) to open dump devices after entering capability
mode, and use cap_syslog(3) to log messages.
- Use a relative directory fd to open output files.
- Use zdopen(3) to compress kernel dumps in capability mode.
Reviewed by: cem, oshogbo
MFC after: 2 months
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18458
By default, bectl is setting the jail 'name' parameter to the boot
environment name, which causes an error when the boot environment name is
not a valid jail name. With the attached fix, when no name is supplied, the
default jail name will be the jail id - this is is the same behavior as the
jail command.
Additionally, this commit addresses two other bugs that prevented unjailing
in scenarios where the jail name does not match the boot environment name:
1. In 'bectl_locate_jail', 'mountpoint' is used to resolve the boot
environment path, but really 'mounted' should be used. 'mountpoint' is the
path where the zfs dataset will be mounted. 'mounted' is the path where
the dataset is actually mounted.
2. in 'bectl_search_jail_paths', 'jail_getv' would fail after the first
call. Which is fine, if the boot environment you're unjailing is the next
one up. According to 'man jail_getv', it's expecting name and value
strings. 'jail_getv' is being passed an integer for the lastjid, so amend
that to use a string instead.
Test cases have been amended to reflect the bugs found.
PR: 233637
Submitted by: Rob <rob.fx907_gmail.com>
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18607
The nvmecontrol code that did the devlist assumed that we had a
tightly-packed allocation of units. Since pci writing exists, this
isn't the case. Loop over the first 256 units, which is a reasonable
number of possible units.
Sponsored by: Netflix
implement not double-caching for reads from vnode-backed md devices.
Use VOP_ADVISE() similarly instead of !IO_DIRECT unsimilarly for writes.
Add a "cache" option to mdconfig to allow changing the default of not
caching.
This depends on a recent commit to fix VOP_ADVISE(). A previous version
had optimizations for sequential i/o's (merge the i/o's and only uncache
for discontiguous i/o's and for full blocks), but optimizations and
knowledge of block boundaries belong in VOP_ADVISE(). Read-ahead should
also be handled better, by supporting it in md and discarding it in
VOP_ADVISE().
POSIX_FADV_DONTNEED is ignored by zfs, but so is IO_DIRECT.
POSIX_FADV_DONTNEED works better than IO_DIRECT if it is not ignored,
since it only discards from the buffer cache immediately, while
IO_DIRECT also discards from the page cache immediately.
IO_DIRECT was not used for writes since it was claimed to be too slow,
but most of the slowness for writes is from doing them synchronously by
default. Non-synchronous writes still deadlock in many cases.
IO_DIRECT only has a special implementation for ffs reads with DIRECTIO
configured. Otherwise, if it is not ignored than it uses the buffer and
page caches normally except for discarding everything after each i/o,
and then it has much the same overheads as POSIX_FADV_DONTNEED. The
overheads for reading with ffs and DIRECTIO were similar in tests of md.
Reviewed by: kib
If requested to fix the inode check-hash it would confirm having done
it, but then fail to make the fix. The same code is used in fsdb which,
unlike fsck, would actually fix the inode check-hash.
The discrepancy occurred because fsck has two ways to fetch inodes.
The inode by number function ginode() and the streaming inode
function getnextinode() used during pass1. Fsdb uses the ginode()
function which correctly does the fix, while fsck first encounters
the bad inode check-hash in pass1 where it is using the getnextinode()
function that failed to make the correction. This patch corrects
the getnextinode() function so that fsck now correctly fixes inodes
with incorrect inode check-hashs.
Reported by: Gary Jennejohn <gljennjohn@gmail.com>
Sponsored by: Netflix
Also use caph_cache_catpages() to ensure that strerror() works when
run with kern.trap_enotcap=1.
Reviewed by: oshogbo
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18514
check hash to the filesystem inodes. Access attempts to files
associated with an inode with an invalid check hash will fail with
EINVAL (Invalid argument). Access is reestablished after an fsck
is run to find and validate the inodes with invalid check-hashes.
This check avoids a class of filesystem panics related to corrupted
inodes. The hash is done using crc32c.
Note this check-hash is for the inode itself and not any of its
indirect blocks. Check-hash validation may be extended to also
cover indirect block pointers, but that will be a separate (and
more costly) feature.
Check hashes are added only to UFS2 and not to UFS1 as UFS1 is
primarily used in embedded systems with small memories and low-powered
processors which need as light-weight a filesystem as possible.
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
opcode will be printed. This should solve the problem, when protocol
name is not printed in `ipfw -N show`.
Reported by: Claudio Eichenberger <cei at yourshop.com>
MFC after: 1 week
Other vendors base their additional smart info pages on what Intel did
plus some other bits. So it's convenient to have this be global.
Sponsored by: Netflix
This was never documented, and isn't needed, so it's best removed to
avoid confusion.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18460
Make the pointers we pass into the commands const, also make the
linker set mirrors const.
Suggested by: cem@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18459
o Dynamically load all the .so files found in /libexec/nvmecontrol and
/usr/local/libexec/nvmecontrol.
o Link nvmecontrol -rdynamic so that its symbols are visible to the
libraries we load.
o Create concatinated linker sets that we dynamically expand.
o Add the linked-in top and logpage linker sets to the mirrors for them
and add those sets to the mirrors when we load a new .so.
o Add some macros to help hide the names of the linker sets.
o Update the man page.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18455
fold
superblock has a check-hash error, an error message noting the
superblock check-hash failure is printed and the mount fails. The
administrator then runs fsck to repair the filesystem and when
successful, the filesystem can once again be mounted.
This approach fails if the filesystem in question is a root filesystem
from which you are trying to boot. Here, the loader fails when trying
to access the filesystem to get the kernel to boot. So it is necessary
to allow the loader to ignore the superblock check-hash error and make
a best effort to read the kernel. The filesystem may be suffiently
corrupted that the read attempt fails, but there is no harm in trying
since the loader makes no attempt to write to the filesystem.
Once the kernel is loaded and starts to run, it attempts to mount its
root filesystem. Once again, failure means that it breaks to its prompt
to ask where to get its root filesystem. Unless you have an alternate
root filesystem, you are stuck.
Since the root filesystem is initially mounted read-only, it is
safe to make an attempt to mount the root filesystem with the failed
superblock check-hash. Thus, when asked to mount a root filesystem
with a failed superblock check-hash, the kernel prints a warning
message that the root filesystem superblock check-hash needs repair,
but notes that it is ignoring the error and proceeding. It does
mark the filesystem as needing an fsck which prevents it from being
enabled for writing until fsck has been run on it. The net effect
is that the reboot fails to single user, but at least at that point
the administrator has the tools at hand to fix the problem.
Reported by: Rick Macklem (rmacklem@)
Discussed with: Warner Losh (imp@)
Sponsored by: Netflix
This can be useful, when net.inet.ip.fw.dyn_keep_states is enabled, but
after rules reloading some state must be deleted. Added new flag '-D'
for such purpose.
Retire '-e' flag, since there can not be expired states in the meaning
that this flag historically had.
Also add "verbose" mode for listing of dynamic states, it can be enabled
with '-v' flag and adds additional information to states list. This can
be useful for debugging.
Obtained from: Yandex LLC
MFC after: 2 months
Sponsored by: Yandex LLC
This was a typo for wdc. Eliminate it since it was in error. People
should use either 'wdc' or 'hgst' for the vendor from now on. 'hgst'
works for all versions this functionality is present for.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Move the Intel specific log pages (including the one that samsung
implements) to intel.c. Add comment to the samsung vendor that it will
be going away soon.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Eliminage redundant spaces and nvmecontrol at start of all the usage
strings. Update the usage printing code to add them back when
presenting to the user. Allow multi-line usage messages and print
proper leading spaces for lines starting with a space.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Provide a usage() function that takes a struct nvme_function pointer
and produces a usage mssage. Eliminate all now-redundant usage
functions. Propigate the new argument through the program as needed.
Use common routine to print usage.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
If the dispatched function doesn't exit, then we get can get a
spurious function not found message. They all do exit, but this is a
little cleaner.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
These are all hgst/wdc specific, so move them into the wdc.c to live
with the wdc command.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
For the upcoming move of vendor specific code into vendor specific
files, make the common logpage routines global and move them to
nvmecontrol.h.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Move logpage function def to header. Convert all the logpage_function
elements to elements of the linker set. Leave them all in logpage.c
for the moment.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
More commands will be added to nvmecontrol. Also, there will be a few
more vendor commands (some of which may need to remain private to
companies writing them). The first step on that journey is to move to
using linker sets to dispatch commands. The next step will be using
dlopen to bring in the .so's that have the command that might need
to remain private for seamless integration.
Similar changes to this will be needed for vendor specific log pages.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
SELECTIVE MIRRORING
If your network has network traffic analyzer connected to your host
directly via dedicated interface or remotely via RSPAN vlan, you can
selectively mirror some ethernet layer2 frames to the analyzer.
...
report the check-hash failure and offer to search for and use
alternate superblocks. Prior to this fix fsck_ffs would simply
report the check-hash failure and exit.
Reported by: Julian H. Stacey <jhs@berklix.com>
Tested by: Peter Holm
Sponsored by: Netflix
Those two manual pages are already referencing each other in the HISTORY
sections, which people might skip. Mention those manual pages explicitly in
the SEE ALSO sections. Also, remove a reference to be(1) from libbe(3).
Reviewed by: bcr
Approved by: krion (mentor, implicit), mat (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D18136
Observed in a CI test image, bectl_create test will run and be marked as
skipped because the module is not loaded. The first zpool invocation will
automagically load the module, but bectl_create is still skipped. Subsequent
tests all pass as expected because the module is now loaded and everything
is OK.
MFC after: 3 days
These tests operate on a file-backed zpool that gets created in the kyua
temp dir. root and ZFS support are both required for these tests. Current
tests cover create, destroy, export/import, jail, list (kind of), mount,
rename, and jail.
List tests should later be extended to cover formatting and the different
list flags, but for now only covers basic "are create/destroy actually
reflected properly"
MFC after: 3 days
Add an undocumented -r option preceding the bectl subcommand to specify a BE
root to operate out of. This will remain undocumented for now, as some
caveats apply:
- BEs cannot be activated in the pool that doesn't contain the rootfs
- bectl create cannot work out of the box without the -e option right now,
since it defaults to the rootfs and cross-pool cloning doesn't work like
that (IIRC)
Plumb the BE root through to libbe(3) so that some things -can- be done to
it, e.g.
bectl -r tank/ROOT create -e default upgrade
bectl -r tank/ROOT mount upgrade /mnt
this aides in some upgrade setups where rootfs is not necessarily ZFS, and
also makes it easier/possible to regression-test bectl when combined with a
file-backed zpool.
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18029
Rather than using a special value to denote "use the default router",
treat the absence of the -g option to mean the same thing. The
in-kernel netdump client will always attempt to reach the server
directly before falling back to the configured gateway anyway. This
change makes it cleaner to support a hostname value for -g.
Reviewed by: cem
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18025
document the libufs interface for fetching and storing inodes.
The undocumented getino / putino interface has been replaced
with a new getinode / putinode interface.
Convert the utilities that had been using the undocumented
interface to use the new documented interface.
No functional change (as for now the libufs library does not
do inode check-hashes).
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
Now an interface name can be specified for nptv6 instance instead of
ext_prefix. The module will track if_addr_ext events and when suitable
IPv6 address will be added to specified interface, it will be configured
as external prefix. When address disappears instance becomes unusable,
i.e. it doesn't match any packets.
Reviewed by: 0mp (manpages)
Tested by: Dries Michiels <driesm dot michiels gmail com>
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D17765
For example, in case of super-user:
$ sudo ping -s -64 127.0.0.1
PING 127.0.0.1 (127.0.0.1): -64 data bytes
ping: sendto: Invalid argument
For unprivileged user:
$ ping -s -64 127.0.0.1
ping: packet size too large: 18446744073709551552 > 56: Operation not permitted
Fix this by switching from strtoul() to strtol() for integer arguments
and adding explicit checks for negative values.
MFC after: 1 month
It produces incompatibility when rules listing is used again to
restore saved ruleset, because "ip6" keyword produces separate opcode.
The kernel already has the check and only IPv6 packets will be checked
for matching.
PR: 232939
MFC after: 3 days
There is no need to check if capdns is NULL.
If we will build the system without casper all cap_gethostaddr will be
replaced by the standard functions.
Make it clear that ipfw action set for layer2 frames it a bit limited.
PR: 59835
Reviewed by: yuripv
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D17719
The buffer is already zeroed in compile_rule() function, and also it
may contain configured F_NOT flag in o.len field. This fixes the filling
for "not icmp6types" opcode.
PR: 232939
MFC after: 3 days
tcpdump can capture packet traces from the usb bus. usbus[0-9] are
registered as ifnet devices so this can work. When these devices come
up, devd was trying to run pccard_ether on those interfaces, which
didn't exist and generated an error.
program to use the libufs library interface. No functional change
(as for now the libufs library does not do inode check-hashes).
Reviewed by: kib
Sponsored by: Netflix
This change defines the RA "6" (IPv6-Only) flag which routers
may advertise, kernel logic to check if all routers on a link
have the flag set and accordingly update a per-interface flag.
If all routers agree that it is an IPv6-only link, ether_output_frame(),
based on the interface flag, will filter out all ETHERTYPE_IP/ARP
frames, drop them, and return EAFNOSUPPORT to upper layers.
The change also updates ndp to show the "6" flag, ifconfig to
display the IPV6_ONLY nd6 flag if set, and rtadvd to allow
announcing the flag.
Further changes to tcpdump (contrib code) are availble and will
be upstreamed.
Tested the code (slightly earlier version) with 2 FreeBSD
IPv6 routers, a FreeBSD laptop on ethernet as well as wifi,
and with Win10 and OSX clients (which did not fall over with
the "6" flag set but not understood).
We may also want to (a) implement and RX filter, and (b) over
time enahnce user space to, say, stop dhclient from running
when the interface flag is set. Also we might want to start
IPv6 before IPv4 in the future.
All the code is hidden under the EXPERIMENTAL option and not
compiled by default as the draft is a work-in-progress and
we cannot rely on the fact that IANA will assign the bits
as requested by the draft and hence they may change.
Dear 6man, you have running code.
Discussed with: Bob Hinden, Brian E Carpenter
When users mark an interface to not use aliases they likely also don't
want to use the link-local v6 address there.
PR: 201695
Submitted by: Russell Yount <Russell.Yount AT gmail.com>
Differential Revision: https://reviews.freebsd.org/D17633
and runs scripts containing "KEYWORD: resume" with single "resume" argument.
Working example is the port sysutils/cpupdate that defines
extra_commands="resume" to reload CPU microcode cleared
by suspend/resume sequence.
This change does nothing for a system having no scripts with KEYWORD: resume.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D15247
that is already present in a kernel statically.
For example, the command "mount_msdosfs -L ru_RU.KOI8-R" fails with error
"mount_msdosfs: msdosfs_iconv: File exists" for a kernel having
options LIBICONV and MSDOSFS_ICONV. After this change, it mounts successfully.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D16951
Previously, route returned 1 in case of error properly signalling failure
but "route -q" it returned 0 for same case. Fix it.
PR: 186333
MFC after: 1 month
Start with a short summary and cover the options in a standard list style.
Organize sections by common focus and prioritize more useful information
closer to the top.
Flesh out authors, history, caveats, and security considerations sections.
Reviewed by: markj, eadler (previous version)
Differential Revision: https://reviews.freebsd.org/D17679
The premise of dumpon -k foo.pem is that dump contents will be confidential
except to anyone holding the corresponding RSA private key.
This guarantee breaks down when weak RSA keys are used. Small RSA keys
(e.g. 512 bits) can be broken on a single personal computer in tractible
time. Marginal RSA keys (768 bits) can be broken by EC2 and a few dollars.
Even 1024 bit keys can probably be broken by sophisticated and wealthy
attackers.
NIST SP800-57 (2016) recommends a minimum of 2048 bit RSA keys, and
estimates this provides 112 bits of security.
It would also be good to protect users from weak values of 'e' (i.e., 3) and
perhaps sanity check that their public key .pem does not accidentally
contain their private key as well. These considerations are left as future
work.
Reviewed by: markj, darius AT dons.net.au (previous version)
Discussed with: bjk
Differential Revision: https://reviews.freebsd.org/D17678
check hash to the superblock. If a check hash fails when an attempt
is made to mount a filesystem, the mount fails with EINVAL (Invalid
argument). This avoids a class of filesystem panics related to
corrupted superblocks. The hash is done using crc32c.
Check hases are added only to UFS2 and not to UFS1 as UFS1 is primarily
used in embedded systems with small memories and low-powered processors
which need as light-weight a filesystem as possible.
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
to switch the output method in run-time. Also document some sysctl
variables that can by changed for NAT64 module.
NAT64 had compile time option IPFIREWALL_NAT64_DIRECT_OUTPUT to use
if_output directly from nat64 module. By default is used netisr based
output method. Now both methods can be used, but they require different
handling by rules.
Obtained from: Yandex LLC
MFC after: 3 weeks
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D16647
that was added using "new rule format". And then, when the kernel
returns rule with this flag, ipfw(8) can correctly show it.
Reported by: lev
MFC after: 3 weeks
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D17373
for already existing interface.
It appeared, that ifconfig(8) assumes `create` keyword as hostname and
tries to resolve it, when `ifconfig ifname create` invoked for already
existing interface. This can produce some unexpected results, when hostname
resolving has successfully happened. This patch adds check for such case.
When an interface is already exists, and create is only one argument,
return error message. But when there are some other arguments, just remove
create keyword from the arguments list.
Obtained from: Yandex LLC
MFC after: 3 weeks
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D17171
Exiting with a signal should not be treated the same as successful exit with
zero status.
Return signal exit information to the callers via negative integers, to
enable distinction from normal exit statuses. (All consumers that check for
errors don't care what the exact non-zero exit value is -- in such a case
they print a diagnostic message and either continue or bail.)
Additionally, check for unexpected sources of waitpid() wakeup and bail if
we encounter them.
Reported by: lev@
Reviewed by: kib, lev, markj (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D17035
When we set the ifname we have to copy the string, rather than just keep
the pointer.
PR: 231323
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D17507
The reasons for this are forward looking to pkgbase:
* /sbin/init is a special binary; try not to replace it with
every package update because an rc script was touched.
(a follow-up commit will make init its own package)
* having rc in its own place will allow more easy replacement
of the rc framework with alternatives, such as openrc.
Discussed with: brd (during BSDCam), kmoore
Requested by: cem, bz
PR: 231522
Approved by: re (gjb)
After r273201 it is supported "/{udp,tcp,proto}" suffix into
$firewall_myservices, and in the rc.conf the information is outdated.
Reviewed by: bcr, rgrimes
Approved by: re (gjb), doc (bcr), src (rgrimes)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D17338
mips64 supports COMPAT_FREEBSD32 (for o32 binaries), so run the 32-bit
compat ldconfig on it as well.
Reported by: brooks
Reviewed by: brooks, kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17342
Since r154114 which introduced ldconfig_local32_dirs, ldconfig -32 was
called with -m. This means that ld-elf32.so.hints paths set is not
cleared for compat32 on boot, unlike ld,so,hints. Same -m was used in
r294295 for ld-elf-soft.so.hints on arm. The patch fixes the
asymmetry.
Noted by: Andreas Longwitz <longwitz@incore.de>
Reviewed by: brooks, emaste, imp
Discussed with: bdrewery
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D17331
when `ifconfig ipsec create reqid N` command invoked without interface
unit number. The "name" global variable is updated after interface
cloning in the ifclonecreate() and contains actual interface name.
Reported by: lev
Approved by: re (kib)
MFC after: 1 week
Don't add it. This should fix when we do regepx matches against
variables we've set and fix wifi bring up.
PR: 231441
Approved by: re@ (kib)
Differential Revision: https://reviews.freebsd.org/D17267
This leverages CONFS to handle the install.
Approved by: re (blanket, pkgbase), will (mentor)
Differential Revision: https://reviews.freebsd.org/D17217
This is being done a separate step to ease importing into other VCSes.
Approved by: re (gjb), will (mentor)
Differential Revision: https://reviews.freebsd.org/D17160
fasthalt has behaved like reboot, instead of like halt, since r228408
(2011, 10.0-RELEASE). Fix it. One wonders if anyone will notice.
Approved by: re (kib)
MFC after: 3 days
Sponsored by: Dell EMC Isilon
Sample output:
% geom -t
Geom Class Provider
da0 DISK da0
da0 PART da0s1
da0s1 PART da0s1a
ffs.da0s1a VFS
da0s1a DEV
da0s1 DEV
da0 DEV
da1 DISK da1
swap SWAP
da1 DEV
cd0 DISK cd0
cd0 DEV
Reviewed by: oshogbo
Approved by: re (kib)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D17151
It completely unnecessarily iterates over all filesystems and happens
to be executed a lot e.g. by synth.
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17143
dhclient and ping normally use libcasper services. These are not
available in statically-linked binaries, so when WITHOUT_DYNAMICROOT is
set disable libcasper use, as with rescue builds. Also emit a warning
as it's undesirable to build this way.
Reported by: Michael Dexter
Reviewed by: rgrimes
Tested by: Michael Dexter
Approved by: re (kib)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17074
Use nitems(), do not assume EFI_MD_TYPE_ contiguous allocation, in
particular, switch to use designated array initializers.
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (gjb)
Add PersistentMemory to the list of sysctl's known memory types
when decoding an EFI memory map.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
MFC after: 1 week
Approved by: re (rgrimes)
And simplify this a little by flattening the directory structure.
Approved by: re (gjb), will (mentor)
Differential Revision: https://reviews.freebsd.org/D16955
In the conversion, the newline got stripped. It worked fine when there
was only one module, but not when there are many. Add back the missing
newline.
Approved by: re@ (kib)
PR: 230868
Differential Revision: https://reviews.freebsd.org/D16895
vermaden (maintainer of beadm) points out the following inconsistencies:
- "missing command" is not printed prior to usage if the error is simply a
missing command; this should be obvious from the context
- "bectl rename" isn't using the "don't unmount" flag (zfs rename -u), so
the active BE can't be renamed. It doesn't make sense in our context to
*not* use -u, so use it.
Documentation updates reflect the above and note an inconsistency with the
'destroy' command that is consistent with other parts of the base system.
A fix for libbe(3) not properly being installed to /lib is included.
SHLIBDIR should have been added when it was moved in r337995.
Approved by: re (kib)
In order to build on a Linux host we need to bootstrap md5 since the Linux
md5sum command produces output in a different format.
Reviewed By: emaste
Approved By: brooks (mentor)
Differential Revision: https://reviews.freebsd.org/D16846
higher bandwidth interfaces. The new value is used above 2.5 Gbps,
which is the highest standard rate that could be used prior to
r338209, so the default behavior for all existing systems should
remain the same.
The value of 128 chosen is a balance between being big enough to
reduce potential precision/quantization effects stemming from frequent
bucket refills over small time intervals and being small enough to
prevent a greedy driver from burst dequeuing more packets than it has
available hardware ring slots for whenever altq transitions from idle
to backlogged.
Reviewed by: jmallett, kp
MFC after: 2 weeks
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D16852
devmatch_blacklist is a space separated list of modules (w/o the .ko
or full path) to exclude from devmatch's processing.
Differential Revision: https://reviews.freebsd.org/D16735
up the device described by the nomatch event in the device tree. If we
find it, then if the device is marked as have already attached to a
device once, then ignore the device.
This keeps us from reloading the device driver when it has just been
manually unloaded. All devies that have had a driver attach to them at
least once no longer participate in pnp-based autoloading.
Differential Revision: https://reviews.freebsd.org/D16735
This flag is set once the device has been successfully attached. When
set, it inhibits devmatch from trying to match the device. This in
turn allows kldunload to work as expected. Prior to the change, the
driver would immediately reload because devmatch had no notion that
the driver had once been attached, and therefore shouldn't participate
in further matching.
Differential Revision: https://reviews.freebsd.org/D16735
This backs out the hack we added in r329458. Now that we can freeze /
thaw probing, this is a much better solution to that problem. Revert
to simply printing the results as we find them, and relying on an
external sort | uniq to clean up the list.
Differential Revision: https://reviews.freebsd.org/D16735
Use devctl freeze / thaw to allow us to laod multiple modules before
doing the probe/attach so they all get a bite at the apple.
Differential Revision: https://reviews.freebsd.org/D16735
- Some overly-long lines
- Consistently using .Brq ({})
- Consistently using .Cm
- Not using .Ao/.Ac around .Ar
PR: 230576
Submitted by: Yuri Pankov (with a fair amount of rebasing pre-commit)
Add a -U flag to get back the old behavior. The new behavior is a little
more friendly to the common use cases, jail the BE and execute a script.
Having the jail torn down automatically when the script is finished, or when
you exit the shell, is a little more friendly than having to remember to
`bectl ujail`.
Batch mode (-b) will continue to leave the jail up, as it's assumed the
caller has other intentions.
Submitted by: Shawn Webb (partially)
2^32 bps or greater to be used. Prior to this, bandwidth parameters
would simply wrap at the 2^32 boundary. The computations in the HFSC
scheduler and token bucket regulator have been modified to operate
correctly up to at least 100 Gbps. No other algorithms have been
examined or modified for correct operation above 2^32 bps (some may
have existing computation resolution or overflow issues at rates below
that threshold). pfctl(8) will now limit non-HFSC bandwidth
parameters to 2^32 - 1 before passing them to the kernel.
The extensions to the pf(4) ioctl interface have been made in a
backwards-compatible way by versioning affected data structures,
supporting all versions in the kernel, and implementing macros that
will cause existing code that consumes that interface to use version 0
without source modifications. If version 0 consumers of the interface
are used against a new kernel that has had bandwidth parameters of
2^32 or greater configured by updated tools, such bandwidth parameters
will be reported as 2^32 - 1 bps by those old consumers.
All in-tree consumers of the pf(4) interface have been updated. To
update out-of-tree consumers to the latest version of the interface,
define PFIOC_USE_LATEST ahead of any includes and use the code of
pfctl(8) as a guide for the ioctls of interest.
PR: 211730
Reviewed by: jmallett, kp, loos
MFC after: 2 weeks
Relnotes: yes
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D16782
This is related to pkgbase as it uses CONFS to properly tag these as config
files.
Approved by: will (mentor)
Differential Revision: https://reviews.freebsd.org/D16785
Rely on the kernel to appropriately mark group members as skipped.
Once a group is skipped we can clear the update flag on all the members.
PR: 229241
Submitted by: Andreas Longwitz <longwitz AT incore.de>
MFC after: 1 week
The original NVMe API used bit-fields to represent fields in data
structures defined by the specification (e.g. the op-code in the command
data structure). The implementation targeted x86_64 processors and
defined the bit fields for little endian dwords (i.e. 32 bits).
This approach does not work as-is for big endian architectures and was
changed to use a combination of bit shifts and masks to support PowerPC.
Unfortunately, this changed the NVMe API and forces #ifdef's based on
the OS revision level in user space code.
This change reverts to something that looks like the original API, but
it uses bytes instead of bit-fields inside the packed command structure.
As a bonus, this works as-is for both big and little endian CPU
architectures.
Bump __FreeBSD_version to 1200081 due to API change
Reviewed by: imp, kbowling, smh, mav
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D16404
This helps with pkgbase as it switches these to using CONFS so they are
properly tagged as config files.
Approved by: will (mentor), imp
Differential Revision: https://reviews.freebsd.org/D16781
Instead of always running /bin/sh, allow the user to specify the command
to run. The jail is not removed when the command finishes. Meaning,
`bectl unjail` will still need to be run.
For example:
```
bectl jail newBE pkg upgrade
bectl ujail newBE
```
Submitted by: Shawn Webb
Obtained from: HardenedBSD (8b451014ab)
Adding batch mode to the jail `bectl(8)` subcommand enables jailing of
ZFS Boot Environments in a scriptable fashion.
Submitted by: Shawn Webb
Obtained from: HardenedBSD (9e72d1c59a and ef7b6d9e1c with minor edit)
Previous iteration of this assumed that these won't fail because we've
already setup the jail param to this point, but the allocations could still
fail in pretty bad conditions.
Admit that it's possible and return (ENOENT, EINVAL, ENOMEM, or 0) when
deleting arguments. EINVAL shouldn't happen since we're passing optarg;
which may satisfy *optarg == '\0' but never optarg == NULL.
CID: 1394885, 1394901
after opening the console, replacing init as PID 1.
From the user point of view, it makes it possible to run eg the
shell as PID 1, using 'set init_exec=/bin/sh' at the loader(8)
prompt.
Reviewed by: kib
MFC after: 2 weeks
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D16625
These were previously necessary because the libnvpair and libzfs_core
includes were not installed into the SYSROOT, being a part of the copies
target in include/Makefile rather than being installed with the library.
This was fixed in r337696 and the headers are now installed properly, so we
may let go of the cruft.
Deleting the temp snapshot isn't immediately possible because it's the
origin of the newly imported boot environment. However, this is trivially
solved by opening the new boot environment and promoting it. The roles are
now reversed and the temp snapshot/dataset may be completely destroyed.
Remove the BUGS from libbe(3) and bectl(8).
bectl(8) is an administrative interface for working with ZFS boot
environments, intended to provide a superset of the functionality provided
by sysutils/beadm.
libbe(3) is the back-end library that the required functionality has been
pulled out into for later reuse.
These were originally written for GSoC 2017 under the mentorship of
allanjude@.
bectl(8) has proven pretty stable in my testing, with the known bug
documented in the man page.
Relnotes: yes
- Missing include path
- Fully specify libzfs's dependencies (except for deps pulled in by other
deps) in Makefile.inc1
- Drop WARNS back down to 2 for libbe(3). I do this with much hesitation,
but the libzfs headers are apparently a hot warning-filled mess as far as
GCC 4.2 is concerned.
Fix bug introduced in r98542: previously to this revision the byte-swapped
value was compared at this place. The current check is in a conditional
section where the non-byte-swapped value was already checked to be not
the value which is checked again. As byte-swapping is activated afterwards,
it only makes sense if the byte-swapped value is checked.
Submitted by: Keith White <kwhite@site.uottawa.ca>
PR: 200059
MFC after: 1 month
Sponsored by: Essen Hackathon
This helps with pkgbase to tag this config file as a config file.
Approved by: allanjude (mentor), will (mentor)
Differential Revision: https://reviews.freebsd.org/D16559
This helps pkgbase as this config file will now be tagged as a config file.
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D16675
Regardless if a verbose scan is required or not, we'd still want to display the
full SSID name by default so use the IEE80211_NWID_LEN constant to set the
value to use instead.
Tested on rene@'s laptop.
Reviewed by: kp
Sponsored by: Essen Hackathon
Differential Revision: https://reviews.freebsd.org/D16566
It's useful for how to mount an iso file via loopback.
Reviewed by: jilles
Approved by: bcr (mentor)
Differential Revision: https://reviews.freebsd.org/D16067
The mostly-undocumented 'add' functionality, from initial read-through, is
intended for construction of deep ("bdrewery style") boot environments.
However, it's mostly broken at this point. `#if SOON` it out on both sides
so that we're not exposing a broken API/feature.
Work will resume on it in due time.
