- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
I initially committed libteken to sys/dev/syscons/teken, but now that
I'm working on a console driver myself, I noticed this was not a good
decision. Move it to sys/teken to make it easier for other drivers to
use a terminal emulator.
Also list teken.c in sys/conf/files, instead of listing it in all the
files.arch files separately.
Unfortunately, the wrappers that are present in pts(4) don't have the
mechanics to allow pty(4) to be unloaded safely, so I'm forcing this kld
to return EBUSY. This also means we have to enable some extra code in
pts(4) unconditionally.
Proposed by: rwatson
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
things a bit:
- use dpcpu data to track the ifps with packets queued up,
- per-cpu locking and driver flags
- along with .nh_drainedcpu and NETISR_POLICY_CPU.
- Put the mbufs in flight reference count, preventing interfaces
from going away, under INVARIANTS as this is a general problem
of the stack and should be solved in if.c/netisr but still good
to verify the internal queuing logic.
- Permit changing the MTU to virtually everythinkg like we do for loopback.
Hook epair(4) up to the build.
Approved by: re (kib)
a device pager (OBJT_DEVICE) object in that it uses fictitious pages to
provide aliases to other memory addresses. The primary difference is that
it uses an sglist(9) to determine the physical addresses for a given offset
into the object instead of invoking the d_mmap() method in a device driver.
Reviewed by: alc
Approved by: re (kensmith)
MFC after: 2 weeks
Driver supports Serial ATA and ATAPI devices, Port Multipliers
(including FIS-based switching), hardware command queues (31 command
per port) and Native Command Queuing. This is probably the second on
popularity, after AHCI, type of SATA2 controllers, that benefits from
using CAM, because of hardware command queuing support.
Approved by: re (kib)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
o add a new facility for components to register send+recv handlers
o ieee80211_send_action and ieee80211_recv_action now use the registered
handlers to dispatch operations
o rev ieee80211_send_action api to enable passing arbitrary data
o rev ieee80211_recv_action api to pass the 802.11 frame header as it may
be difficult to locate
o update existing IEEE80211_ACTION_CAT_BA and IEEE80211_ACTION_CAT_HT handling
o update mwl for api rev
Reviewed by: rpaulo
Approved by: re (kensmith)
This removes unnecessary PCI #includes dependency for systems with ATA
controllers living at non-PCI buses.
Submitted by: Piotr Ziecik
Obtained from: Semihalf
the PHYs as some PHY drivers use it (but probably shouldn't). How
gem(4) has worked with brgphy(4) on powerpc without this so far is
unclear to me.
- Introduce a dying flag which is set during detach and checked in
gem_ioctl() in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- In gem_stop() reset rather than just disable the transmitter and
receiver in order to ensure we're not unloading DMA maps still in
use by the hardware. [1]
- The blanking time is specified in PCI clocks so we should use twice
the value when operating at 66MHz.
- Spell some 2 as ETHER_ALIGN and a 19 as GEM_STATUS_TX_COMPLETION_SHFT
to make the actual intentions clear.
- As we don't unload the peak attempts counter ignore its overflow
interrupts.
- Remove a stale setting of a variable to GEM_TD_INTERRUPT_ME which
isn't used afterwards.
- For optimum performance increment the TX kick register in multiples
of 4 if possible as suggested by the documentation.
- Partially revert r164931; drivers should only clear the watchdog
timer if all outstanding TX descriptors are done.
- Fix some debugging strings.
- Add a missing BUS_DMASYNC_POSTWRITE in gem_rint().
- As the error paths in the interrupt handler are generally unlikely
predict them as false.
- Add support for the SBus version of the GEM controller. [2]
- Add some lock assertions.
- Improve some comments.
- Fix some more or less cosmetic issues in the code of the PCI front-end.
- Change some softc members to be unsigned where more appropriate and
remove unused ones.
Approved by: re (kib)
Obtained from: NetBSD (partially) [2], OpenBSD [1]
MFC after: 2 weeks
* Driver for ACPI HP extra functionations, which required
ACPI WMI driver.
Submitted by: Michael <freebsdusb at bindone.de>
Approved by: re
MFC after: 2 weeks
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
DP83065 Saturn Gigabit Ethernet controllers. These are the successors
of the Sun GEM controllers and still have a similar but extended transmit
logic. As such this driver is based on gem(4).
Thanks to marcel@ for providing a Sun Quad GigaSwift Ethernet UTP (QGE)
card which was vital for getting this driver to work on architectures
not using Open Firmware.
Approved by: re (kib)
MFC after: 2 weeks
cksum related function calls, sometimes related to offload features
from what I could see.xi
It would be good if the offload functionality would be properly
#ifdefed but the other calls to cksum related functions are a more
general problem also elswhere in the network stack.
use IPv4/v6 for inter-node communication (according to my reading).
Properly wrap the carp callouts in INET || INET6 and refelect this
in sys/conf/files as well. While in theory this should be ok,
it might be a bit optimistic to think that carp could build with
inet6 only[1].
Discussed with: mlaier [1]
be nfs_nfsdport.c and nfs_nfsdcache.c are the problem only but we need
to mark all or we will run into problems at link time.
One is because of calling an INET specific function, the other is
because of VIMAGE putting all tcp* into struct vnet_inet.
Both are general problems throughout the entire stack and not a fault
of the NFS implementation and will need to be addressed in the future.
#error "Huh? if_gre without inet?"
According to my reading we still only support encapsulating datagrams
into IPv4 and not IPv6 so there is no optional | gre inet6 yet.
controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
adjust conf/files and modules' Makefiles accordingly.
No code or ABI changes so this and most of previous related
changes can be easily MFC'ed
MFC after: 5 days
Clists were originally used by the TTY layer as a text buffer interface.
The advantage of clists were that it would allocate a small set of
additional buffers that could be shared between TTYs when needed. In
the modern days we can just allocate some more KBs of memory to keep the
TTYs satisfied. The global cfreelist also requires synchronisation,
which may not be useful when trying to improve scalability.
The MPSAFE TTY layer uses its own text buffers (ttyinq and ttyoutq). We
had a small amount of drivers in the tree that still uses clists, like
the old USB stack and some keyboard drivers. With the old USB stack gone
and the keyboard drivers changed to use a circular buffer, we can safely
remove clists from the kernel.
Each list describes a logical memory object that is backed by one or more
physical address ranges. To minimize locking, the sglist objects
themselves are immutable once they are shared.
These objects may be used in the future to facilitate I/O requests using
physically-addressed buffers. For the immediate future I plan to use them
to implement a new type of VM object and pager.
Reviewed by: jeff, scottl
MFC after: 1 month
includes support for NFSv4. The subsystem can optionally be linked
into the kernel using the two options:
NFSCL - the client
NFSD - the server
It is also built as three modules:
nfscl - the client
nfsd - the server
nfscommon - functions shared by the client and server
Approved by: kib (mentor)
Add support for kernel fault injection using KFAIL_POINT_* macros and
fail_point_* infrastructure. Add example fail point in vfs_bio.c to
simulate VM buf pressure.
Approved by: dfr (mentor)
get a quick snapshot of the kernel's symbol table including the symbols
from any loaded modules (the symbols are all merged into one symbol
table). Unlike like other implementations, this ksyms driver maps
memory in the process memory space to store the snapshot at the time
/dev/ksyms is opened. It also checks to see if the process has already
a snapshot open and won't allow it to open /dev/ksyms it again until it
closes first. This prevents kernel and process memory from being
exhausted. Note that /dev/ksyms is used by the lockstat(1) command.
Reviewed by: gallatin kib (freebsd-arch)
Approved by: gnn (mentor)
adds probes for mutexes, reader/writer and shared/exclusive locks to
gather contention statistics and other locking information for
dtrace scripts, the lockstat(1M) command and other potential
consumers.
Reviewed by: attilio jhb jb
Approved by: gnn (mentor)
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.
This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.
The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.
The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.
This change also introduces a DDB subcommand to show the list of all
vnet instances.
Approved by: julian (mentor)
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
import from p4 bms_netdev. Summary of changes:
* Connect netinet6/in6_mcast.c to build.
The legacy KAME KPIs are mostly preserved.
* Eliminate now dead code from ip6_output.c.
Don't do mbuf bingo, we are not going to do RFC 2292 style
CMSG tricks for multicast options as they are not required
by any current IPv6 normative reference.
* Refactor transports (UDP, raw_ip6) to do own mcast filtering.
SCTP, TCP unaffected by this change.
* Add ip6_msource, in6_msource structs to in6_var.h.
* Hookup mld_ifinfo state to in6_ifextra, allocate from
domifattach path.
* Eliminate IN6_LOOKUP_MULTI(), it is no longer referenced.
Kernel consumers which need this should use in6m_lookup().
* Refactor IPv6 socket group memberships to use a vector (like IPv4).
* Update ifmcstat(8) for IPv6 SSM.
* Add witness lock order for IN6_MULTI_LOCK.
* Move IN6_MULTI_LOCK out of lower ip6_output()/ip6_input() paths.
* Introduce IP6STAT_ADD/SUB/INC/DEC as per rwatson's IPv4 cleanup.
* Update carp(4) for new IPv6 SSM KPIs.
* Virtualize ip6_mrouter socket.
Changes mostly localized to IPv6 MROUTING.
* Don't do a local group lookup in MROUTING.
* Kill unused KAME prototypes in6_purgemkludge(), in6_restoremkludge().
* Preserve KAME DAD timer jitter behaviour in MLDv1 compatibility mode.
* Bump __FreeBSD_version to 800084.
* Update UPDATING.
NOTE WELL:
* This code hasn't been tested against real MLDv2 queriers
(yet), although the on-wire protocol has been verified in Wireshark.
* There are a few unresolved issues in the socket layer APIs to
do with scope ID propagation.
* There is a LOR present in ip6_output()'s use of
in6_setscope() which needs to be resolved. See comments in mld6.c.
This is believed to be benign and can't be avoided for the moment
without re-introducing an indirect netisr.
This work was mostly derived from the IGMPv3 implementation, and
has been sponsored by a third party.
pointers to "dead" implementations that no-op rather than invoking
the device driver. This would generally be unexpected and
possibly quite badly handled by most device drivers after
if_detach() has completed.
Reviewed by: bms
MFC after: 3 weeks
- Add and use mapping of fcntl(2) commands to new BSM constant space.
- Adopt (int) rather than (long) arguments to a number of auditon(2)
commands, as has happened in Solaris, and add compatibility code to
handle the old comments.
Note that BSM_PF_IEEE80211 is partially but not fully removed, as the
userspace OpenBSM 1.1alpha5 code still depends on it. Once userspace
is updated, I'll GCC the kernel constant.
MFC after: 2 weeks
Sponsored by: Apple, Inc.
Obtained from: TrustedBSD Project
Portions submitted by: sson
as well as providing stateful load balancing when used with RADIX_MPATH.
- Currently compiled in to i386 and amd64 but disabled by default, it can be enabled at
runtime with 'sysctl net.inet.flowtable.enable=1'.
- Embedded users can remove it entirely from the kernel by adding 'nooption FLOWTABLE' to
their kernel config files.
- A minimal hookup will be added to ip_output in a subsequent commit. I would like to see
more review before bringing in changes that require more churn.
Supported by: Bitgravity Inc.
in sys/nfs/nfs_nfssvc.c by registering with it using the
nfsd_call_nfsserver function pointer. Also, add the build glue for
nfs_nfssvc.c optionally based on "nfsserver" and also as a loadable
module.
Submitted by: rmacklem
Reviewed by: kib
Approved by: kib (mentor)
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
in FreeBSD 5.x to allow network device drivers to run with Giant
despite the network stack being Giant-free. This significantly
simplifies calls into ioctl() on network interfaces, especially
in the multicast code, as well as eliminates deferred invocation
of interface if_start routines.
Disable the build on device drivers still depending on
IFF_NEEDSGIANT as they no longer compile. They will be removed
in a few weeks if they haven't been made MPSAFE in that time.
Disabled drivers:
if_ar
if_axe
if_aue
if_cdce
if_cue
if_kue
if_ray
if_rue
if_rum
if_sr
if_udav
if_ural
if_zyd
Drivers that were already disabled because of tty changes:
if_ppp
if_sl
Discussed on: arch@
o add 9280 attach that sets up ini, cal, etc.
o new rf backend for 9280 and later parts
o split ini setup and spur mitigation support out to methods
and provide 9280-specific support
o minor fixups to shared code to handle 9280-specific work
Obtained from: Atheros (ini values and some code)
Tested on an HD3850 (RV670) on loan from Warren Block.
Currently, you need one of the following for this to be useful:
x11-drivers/xf86-video-radeonhd-devel (not tested)
xf86-video-ati from git (EXA works, xv is too fast)
xf86-video-radeonhd from git (EXA works, xv works)
There is no 3d support available from dri just yet.
MFC after: 2 weeks
contrib/openbsm (svn merge) and src/sys/{bsm,security/audit} (manual
merge). Hook up bsm_domain.c and bsm_socket_type.c to the libbsm
build along with man pages, add audit_bsm_domain.c and
audit_bsm_socket_type.c to the kernel environment.
OpenBSM history for imported revisions below for reference.
MFC after: 1 month
Sponsored by: Apple Inc.
Obtained from: TrustedBSD Project
OpenBSM 1.1 alpha 5
- Stub libauditd(3) man page added.
- All BSM error number constants with BSM_ERRNO_.
- Interfaces to convert between local and BSM socket types and protocol
families have been added: au_bsm_to_domain(3), au_bsm_to_socket_type(3),
au_domain_to_bsm(3), and au_socket_type_to_bsm(3), along with definitions
of constants in audit_domain.h and audit_socket_type.h. This improves
interoperability by converting local constant spaces, which vary by OS, to
and from Solaris constants (where available) or OpenBSM constants for
protocol domains not present in Solaris (a fair number). These routines
should be used when generating and interpreting extended socket tokens.
- Fix build warnings with full gcc warnings enabled on most supported
platforms.
- Don't compile error strings into bsm_errno.c when building it in the kernel
environment.
- When started by launchd, use the label com.apple.auditd rather than
org.trustedbsd.auditd.
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
module. These files cause manual interaction when building
ports/audio/aureal-kmod which provides a usable i386-only driver (it requires
linking against some linux object files distributed by vendor which bankrupted
back in 2000).
MFC after: 1 week
Some time ago I started working on a library called libteken, which is
terminal emulator. It does not buffer any screen contents, but only
keeps terminal state, such as cursor position, attributes, etc. It
should implement all escape sequences that are implemented by the
cons25 terminal emulator, but also a fair amount of sequences that are
present in VT100 and xterm.
A lot of random notes, which could be of interest to users/developers:
- Even though I'm leaving the terminal type set to `cons25', users can
do experiments with placing `xterm-color' in /etc/ttys. Because we
only implement a subset of features of xterm, this may cause
artifacts. We should consider extending libteken, because in my
opinion xterm is the way to go. Some missing features:
- Keypad application mode (DECKPAM)
- Character sets (SCS)
- libteken is filled with a fair amount of assertions, but unfortunately
we cannot go into the debugger anymore if we fail them. I've done
development of this library almost entirely in userspace. In
sys/dev/syscons/teken there are two applications that can be helpful
when debugging the code:
- teken_demo: a terminal emulator that can be started from a regular
xterm that emulates a terminal using libteken. This application can
be very useful to debug any rendering issues.
- teken_stress: a stress testing application that emulates random
terminal output. libteken has literally survived multiple terabytes
of random input.
- libteken also includes support for UTF-8, but unfortunately our input
layer and font renderer don't support this. If users want to
experiment with UTF-8 support, they can enable `TEKEN_UTF8' in
teken.h. If you recompile your kernel or the teken_demo application,
you can hold some nice experiments.
- I've left PC98 the way it is right now. The PC98 platform has a custom
syscons renderer, which supports some form of localised input. Maybe
we should port PC98 to libteken by the time syscons supports UTF-8?
- I've removed the `dumb' terminal emulator. It has been broken for
years. It hasn't survived the `struct proc' -> `struct thread'
conversion.
- To prevent confusion among people that want to hack on libteken:
unlike syscons, the state machines that parse the escape sequences are
machine generated. This means that if you want to add new escape
sequences, you have to add an entry to the `sequences' file. This will
cause new entries to be added to `teken_state.h'.
- Any rendering artifacts that didn't occur prior to this commit are by
accident. They should be reported to me, so I can fix them.
Discussed on: current@, hackers@
Discussed with: philip (at 25C3)
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
container structures, depending on VIMAGE_GLOBALS compile time option.
Make VIMAGE_GLOBALS a new compile-time option, which by default will not
be defined, resulting in instatiations of global variables selected for
V_irtualization (enclosed in #ifdef VIMAGE_GLOBALS blocks) to be
effectively compiled out. Instantiate new global container structures
to hold V_irtualized variables: vnet_net_0, vnet_inet_0, vnet_inet6_0,
vnet_ipsec_0, vnet_netgraph_0, and vnet_gif_0.
Update the VSYM() macro so that depending on VIMAGE_GLOBALS the V_
macros resolve either to the original globals, or to fields inside
container structures, i.e. effectively
#ifdef VIMAGE_GLOBALS
#define V_rt_tables rt_tables
#else
#define V_rt_tables vnet_net_0._rt_tables
#endif
Update SYSCTL_V_*() macros to operate either on globals or on fields
inside container structs.
Extend the internal kldsym() lookups with the ability to resolve
selected fields inside the virtualization container structs. This
applies only to the fields which are explicitly registered for kldsym()
visibility via VNET_MOD_DECLARE() and vnet_mod_register(), currently
this is done only in sys/net/if.c.
Fix a few broken instances of MODULE_GLOBAL() macro use in SCTP code,
and modify the MODULE_GLOBAL() macro to resolve to V_ macros, which in
turn result in proper code being generated depending on VIMAGE_GLOBALS.
De-virtualize local static variables in sys/contrib/pf/net/pf_subr.c
which were prematurely V_irtualized by automated V_ prepending scripts
during earlier merging steps. PF virtualization will be done
separately, most probably after next PF import.
Convert a few variable initializations at instantiation to
initialization in init functions, most notably in ipfw. Also convert
TUNABLE_INT() initializers for V_ variables to TUNABLE_FETCH_INT() in
initializer functions.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
This bring huge amount of changes, I'll enumerate only user-visible changes:
- Delegated Administration
Allows regular users to perform ZFS operations, like file system
creation, snapshot creation, etc.
- L2ARC
Level 2 cache for ZFS - allows to use additional disks for cache.
Huge performance improvements mostly for random read of mostly
static content.
- slog
Allow to use additional disks for ZFS Intent Log to speed up
operations like fsync(2).
- vfs.zfs.super_owner
Allows regular users to perform privileged operations on files stored
on ZFS file systems owned by him. Very careful with this one.
- chflags(2)
Not all the flags are supported. This still needs work.
- ZFSBoot
Support to boot off of ZFS pool. Not finished, AFAIK.
Submitted by: dfr
- Snapshot properties
- New failure modes
Before if write requested failed, system paniced. Now one
can select from one of three failure modes:
- panic - panic on write error
- wait - wait for disk to reappear
- continue - serve read requests if possible, block write requests
- Refquota, refreservation properties
Just quota and reservation properties, but don't count space consumed
by children file systems, clones and snapshots.
- Sparse volumes
ZVOLs that don't reserve space in the pool.
- External attributes
Compatible with extattr(2).
- NFSv4-ACLs
Not sure about the status, might not be complete yet.
Submitted by: trasz
- Creation-time properties
- Regression tests for zpool(8) command.
Obtained from: OpenSolaris
fix the problems a few people have noticed with the new code. People who want
to continue testing the new code or who need RPCSEC_GSS support should use
the new option NFS_NEWRPC to select it.
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
and server. This replaces the RPC implementation of the NFS client and
server with the newer RPC implementation originally developed
(actually ported from the userland sunrpc code) to support the NFS
Lock Manager. I have tested this code extensively and I believe it is
stable and that performance is at least equal to the legacy RPC
implementation.
The NFS code currently contains support for both the new RPC
implementation and the older legacy implementation inherited from the
original NFS codebase. The default is to use the new implementation -
add the NFS_LEGACYRPC option to fall back to the old code. When I
merge this support back to RELENG_7, I will probably change this so
that users have to 'opt in' to get the new code.
To use RPCSEC_GSS on either client or server, you must build a kernel
which includes the KGSSAPI option and the crypto device. On the
userland side, you must build at least a new libc, mountd, mount_nfs
and gssd. You must install new versions of /etc/rc.d/gssd and
/etc/rc.d/nfsd and add 'gssd_enable=YES' to /etc/rc.conf.
As long as gssd is running, you should be able to mount an NFS
filesystem from a server that requires RPCSEC_GSS authentication. The
mount itself can happen without any kerberos credentials but all
access to the filesystem will be denied unless the accessing user has
a valid ticket file in the standard place (/tmp/krb5cc_<uid>). There
is currently no support for situations where the ticket file is in a
different place, such as when the user logged in via SSH and has
delegated credentials from that login. This restriction is also
present in Solaris and Linux. In theory, we could improve this in
future, possibly using Brooks Davis' implementation of variant
symlinks.
Supporting RPCSEC_GSS on a server is nearly as simple. You must create
service creds for the server in the form 'nfs/<fqdn>@<REALM>' and
install them in /etc/krb5.keytab. The standard heimdal utility ktutil
makes this fairly easy. After the service creds have been created, you
can add a '-sec=krb5' option to /etc/exports and restart both mountd
and nfsd.
The only other difference an administrator should notice is that nfsd
doesn't fork to create service threads any more. In normal operation,
there will be two nfsd processes, one in userland waiting for TCP
connections and one in the kernel handling requests. The latter
process will create as many kthreads as required - these should be
visible via 'top -H'. The code has some support for varying the number
of service threads according to load but initially at least, nfsd uses
a fixed number of threads according to the value supplied to its '-n'
option.
Sponsored by: Isilon Systems
MFC after: 1 month
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
One of the pieces of code that I had left alone during the development
of the MPSAFE TTY layer, was tty_cons.c. This file actually has two
different functions:
- It contains low-level console input/output routines (cnputc(), etc).
- It creates /dev/console and wraps all its cdevsw calls to the
appropriate TTY.
This commit reimplements the second set of functions by moving it
directly into the TTY layer. /dev/console is now a character device node
that's basically a regular TTY, but does a lookup of `si_drv1' each time
you open it. d_write has also been changed to call log_console().
d_close() is not present, because we must make sure we don't revoke the
TTY after writing a log message to it.
Even though I'm not convinced this is in line with the future directions
of our console code, it is a good move for now. It removes recursive
locking from the top half of the TTY layer. The previous implementation
called into the TTY layer with Giant held.
I'm renaming tty_cons.c to kern_cons.c now. The code hardly contains any
TTY related bits, so we'd better give it a less misleading name.
Tested by: Andrzej Tobola <ato iem pw edu pl>,
Carlos A.M. dos Santos <unixmania gmail com>,
Eygene Ryabinkin <rea-fbsd codelabs ru>
Memory Interface (CFI). The flash memory can be read and written
to through /dev/cfi# and an ioctl() exists so processes can read
the query information.
The driver supports the AMD and Intel command set, though only
the AMD command has been tested.
Obtained from: Juniper Networks, Inc.
Driver supports PCI devices with class 8 and subclass 5 according to
SD Host Controller Specification.
Update NOTES, enable module and static build.
Enable related mmc and mmcsd modules build.
Discussed on: mobile@, current@
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
in GENERIC and LINT. [1]
- Rename hpt_dbg_level to hpt_iop_dbg_level to avoid multiple definition
of hpt_dbg_level (hptmv also has hpt_dbg_level).
PR: 127551 [1]
Reviewed by: scottl@
MFC after: 1 month
and bcmp are not the same thing. 'man bcmp' states that the return is
"non-zero" if the two byte strings are not identical. Where as,
'man memcmp' states that the return is the "difference between the
first two differing bytes (treated as unsigned char values" if the
two byte strings are not identical.
So provide a proper memcmp(9), but it is a C implementation not a tuned
assembly implementation. Therefore bcmp(9) should be preferred over memcmp(9).
This is a sync to mesa/drm pre-gem, with a few fixes on top of that.
It also contains one local patch supplied by kib@ that I can't apply to
git.master shared code.
Approved by: flz
Obtained from: mesa/drm git.master
MFC after: 2 weeks
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
The ttyinfo() routine generates the fancy output when pressing ^T. Right
now it is stored in tty.c. In the MPSAFE TTY code it is already stored
in tty_info.c. To make integration of the MPSAFE TTY code a little
easier, take the same approach.
This makes the TTY code a little bit more readable, because having the
proc_*/thread_* routines in tty.c is very distractful.
Approved by: philip (mentor)
MPSAFE patches on current@ and stable@. This driver also has a fundamental
issue in that it sleeps when sending commands to the card including in the
if_init/if_start routines (which can be called from interrupt context). As
such, the driver shouldn't be working reliably even on 4.x.
and stable@. It also is a driver for an older non-802.11 wireless PC card
that is quite slow in comparison to say, wi(4). I know Warner wants this
driver axed as well.
provides the correct semantics for flock(2) style locks which are used by the
lockf(1) command line tool and the pidfile(3) library. It also implements
recovery from server restarts and ensures that dirty cache blocks are written
to the server before obtaining locks (allowing multiple clients to use file
locking to safely share data).
Sponsored by: Isilon Systems
PR: 94256
MFC after: 2 weeks
- It is opt-out for now so as to give it maximum testing, but it may be
turned opt-in for stable branches depending on the consensus. You
can turn it off with WITHOUT_SSP.
- WITHOUT_SSP was previously used to disable the build of GNU libssp.
It is harmless to steal the knob as SSP symbols have been provided
by libc for a long time, GNU libssp should not have been much used.
- SSP is disabled in a few corners such as system bootstrap programs
(sys/boot), process bootstrap code (rtld, csu) and SSP symbols themselves.
- It should be safe to use -fstack-protector-all to build world, however
libc will be automatically downgraded to -fstack-protector because it
breaks rtld otherwise.
- This option is unavailable on ia64.
Enable GCC stack protection (aka Propolice) for kernel:
- It is opt-out for now so as to give it maximum testing.
- Do not compile your kernel with -fstack-protector-all, it won't work.
Submitted by: Jeremie Le Hen <jeremie@le-hen.org>
of whether NETATALKDEBUG is enabled, so make building it conditional on
NETATALK instead. This problem appears to have been present from the time
that the netatalk implementation was imported.
PR: 124456
Submitted by: Nathan Whitehorn <whitehorn at wisc dot edu>
MFC after: 3 days
sn(4) driver and also looking at newer drivers. The reason for the rewrite is
to support MII and to try and resolve some performance issues found when trying
to use the sn(4) driver on the Gumstix network boards.
For reference, the SMSC LAN91C111 is a non-PCI ethernet part whose lineage
dates back to Ye Olde Days of ISA. It seems to get some use in the embedded
space these days on parts lacking on-board MACs or on-board PCI controllers,
such as the XScale PXA line of ARM CPUs.
This also includes a driver for the SMSC LAN83C183 10/100 PHY.
Man page to follow.
Because clists are also used outside the TTY layer, rename the file
containing the clist routines to something more accurate.
The mpsafetty TTY layer doesn't use clists. It uses its own buffers,
which also implement the unbuffered copying to userspace. We cannot
simply remove the clist routines then, because this would break various
drivers that are present within the kernel.
Approved by: philip (mentor)
parts relied on the now removed NET_NEEDS_GIANT.
Most of I4B has been disconnected from the build
since July 2007 in HEAD/RELENG_7.
This is what was removed:
- configuration in /etc/isdn
- examples
- man pages
- kernel configuration
- sys/i4b (drivers, layers, include files)
- user space tools
- i4b support from ppp
- further documentation
Discussed with: rwatson, re
NET_NEEDS_GIANT. netatm has been disconnected from the build for ten
months in HEAD/RELENG_7. Specifics:
- netatm include files
- netatm command line management tools
- libatm
- ATM parts in rescue and sysinstall
- sample configuration files and documents
- kernel support as a module or in NOTES
- netgraph wrapper nodes for netatm
- ctags data for netatm.
- netatm-specific device drivers.
MFC after: 3 weeks
Reviewed by: bz
Discussed with: bms, bz, harti
-It has new hardware support
-It uses a new method of TX cleanup called Head Write Back
-It includes the provisional generic TCP LRO feature contributed
by Myricom and made general purpose by me. This should move into
the stack upon approval but for this driver drop its in here.
-Also bug fixes and etc...
MFC in a week if no serious issues arise.
perform various operations on a controller. Specifically, for each mpt(4)
device, create a character device in devfs which accepts ioctl requests for
reading and writing configuration pages and performing RAID actions.
MFC after: 1 week
Reviewed by: scottl
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
move most offload functionality from NIC to TOE
factor out all socket and inpcb direct access
factor out access to locking in incpb, pcbinfo, and sockbuf
(ECMP) for both IPv4 and IPv6. Previously, multipath route insertion
is disallowed. For example,
route add -net 192.103.54.0/24 10.9.44.1
route add -net 192.103.54.0/24 10.9.44.2
The second route insertion will trigger an error message of
"add net 192.103.54.0/24: gateway 10.2.5.2: route already in table"
Multiple default routes can also be inserted. Here is the netstat
output:
default 10.2.5.1 UGS 0 3074 bge0 =>
default 10.2.5.2 UGS 0 0 bge0
When multipath routes exist, the "route delete" command requires
a specific gateway to be specified or else an error message would
be displayed. For example,
route delete default
would fail and trigger the following error message:
"route: writing to routing socket: No such process"
"delete net default: not in table"
On the other hand,
route delete default 10.2.5.2
would be successful: "delete net default: gateway 10.2.5.2"
One does not have to specify a gateway if there is only a single
route for a particular destination.
I need to perform more testings on address aliases and multiple
interfaces that have the same IP prefixes. This patch as it
stands today is not yet ready for prime time. Therefore, the ECMP
code fragments are fully guarded by the RADIX_MPATH macro.
Include the "options RADIX_MPATH" in the kernel configuration
to enable this feature.
Reviewed by: robert, sam, gnn, julian, kmacy
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also fixed in this code.
user-mode lock manager, build a kernel with the NFSLOCKD option and
add '-k' to 'rpc_lockd_flags' in rc.conf.
Highlights include:
* Thread-safe kernel RPC client - many threads can use the same RPC
client handle safely with replies being de-multiplexed at the socket
upcall (typically driven directly by the NIC interrupt) and handed
off to whichever thread matches the reply. For UDP sockets, many RPC
clients can share the same socket. This allows the use of a single
privileged UDP port number to talk to an arbitrary number of remote
hosts.
* Single-threaded kernel RPC server. Adding support for multi-threaded
server would be relatively straightforward and would follow
approximately the Solaris KPI. A single thread should be sufficient
for the NLM since it should rarely block in normal operation.
* Kernel mode NLM server supporting cancel requests and granted
callbacks. I've tested the NLM server reasonably extensively - it
passes both my own tests and the NFS Connectathon locking tests
running on Solaris, Mac OS X and Ubuntu Linux.
* Userland NLM client supported. While the NLM server doesn't have
support for the local NFS client's locking needs, it does have to
field async replies and granted callbacks from remote NLMs that the
local client has contacted. We relay these replies to the userland
rpc.lockd over a local domain RPC socket.
* Robust deadlock detection for the local lock manager. In particular
it will detect deadlocks caused by a lock request that covers more
than one blocking request. As required by the NLM protocol, all
deadlock detection happens synchronously - a user is guaranteed that
if a lock request isn't rejected immediately, the lock will
eventually be granted. The old system allowed for a 'deferred
deadlock' condition where a blocked lock request could wake up and
find that some other deadlock-causing lock owner had beaten them to
the lock.
* Since both local and remote locks are managed by the same kernel
locking code, local and remote processes can safely use file locks
for mutual exclusion. Local processes have no fairness advantage
compared to remote processes when contending to lock a region that
has just been unlocked - the local lock manager enforces a strict
first-come first-served model for both local and remote lockers.
Sponsored by: Isilon Systems
PR: 95247 107555 115524 116679
MFC after: 2 weeks
overhead of packet capture by allowing a user process to directly "loan"
buffer memory to the kernel rather than using read(2) to explicitly copy
data from kernel address space.
The user process will issue new BPF ioctls to set the shared memory
buffer mode and provide pointers to buffers and their size. The kernel
then wires and maps the pages into kernel address space using sf_buf(9),
which on supporting architectures will use the direct map region. The
current "buffered" access mode remains the default, and support for
zero-copy buffers must, for the time being, be explicitly enabled using
a sysctl for the kernel to accept requests to use it.
The kernel and user process synchronize use of the buffers with atomic
operations, avoiding the need for system calls under load; the user
process may use select()/poll()/kqueue() to manage blocking while
waiting for network data if the user process is able to consume data
faster than the kernel generates it. Patchs to libpcap are available
to allow libpcap applications to transparently take advantage of this
support. Detailed information on the new API may be found in bpf(4),
including specific atomic operations and memory barriers required to
synchronize buffer use safely.
These changes modify the base BPF implementation to (roughly) abstrac
the current buffer model, allowing the new shared memory model to be
added, and add new monitoring statistics for netstat to print. The
implementation, with the exception of some monitoring hanges that break
the netstat monitoring ABI for BPF, will be MFC'd.
Zerocopy bpf buffers are still considered experimental are disabled
by default. To experiment with this new facility, adjust the
net.bpf.zerocopy_enable sysctl variable to 1.
Changes to libpcap will be made available as a patch for the time being,
and further refinements to the implementation are expected.
Sponsored by: Seccuris Inc.
In collaboration with: rwatson
Tested by: pwood, gallatin
MFC after: 4 months [1]
[1] Certain portions will probably not be MFCed, specifically things
that can break the monitoring ABI.
rqindex back in struct thread.
- Compile kern_switch.c independently again and stop #include'ing it from
schedulers.
- Remove the ts_thread backpointers and convert most code to go from
struct thread to struct td_sched.
- Cleanup the ts_flags #define garbage that was causing us to sometimes
do things that expanded to td->td_sched->ts_thread->td_flags in 4BSD.
- Export the kern.sched sysctl node in sysctl.h
vm/vm_contig.c, vm/vm_page.c, and vm/vm_pageq.c. Today, vm/vm_pageq.c
has withered to the point that it contains only four short functions,
two of which are only used by vm/vm_page.c. Since I can't foresee any
reason for vm/vm_pageq.c to grow, it is time to fold the remaining
contents of vm/vm_pageq.c back into vm/vm_page.c.
Add some comments. Rename one of the functions, vm_pageq_enqueue(),
that is now static within vm/vm_page.c to vm_page_enqueue().
Eliminate PQ_MAXCOUNT as it no longer serves any purpose.
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
The kernel config file is KERNCONF=MPC85XX, so the usual procedure applies:
1. make buildworld TARGET_ARCH=powerpc
2. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
This default config uses kernel-level FPU emulation. For the soft-float world
approach:
1. make buildworld TARGET_ARCH=powerpc TARGET_CPUTYPE=e500
2. disable FPU_EMU option in sys/powerpc/conf/MPC85XX
3. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
Approved by: cognet (mentor)
MFp4: e500
and assignment.
- Add a reference to a struct cpuset in each thread that is inherited from
the thread that created it.
- Release the reference when the thread is destroyed.
- Add prototypes for syscalls and macros for manipulating cpusets in
sys/cpuset.h
- Add syscalls to create, get, and set new numbered cpusets:
cpuset(), cpuset_{get,set}id()
- Add syscalls for getting and setting affinity masks for cpusets or
individual threads: cpuid_{get,set}affinity()
- Add types for the 'level' and 'which' parameters for the cpuset. This
will permit expansion of the api to cover cpu masks for other objects
identifiable with an id_t integer. For example, IRQs and Jails may be
coming soon.
- The root set 0 contains all valid cpus. All thread initially belong to
cpuset 1. This permits migrating all threads off of certain cpus to
reserve them for special applications.
Sponsored by: Nokia
Discussed with: arch, rwatson, brooks, davidxu, deischen
Reviewed by: antoine
not have VTOC information about the partitions, it will be created.
This is because the VTOC information is used for the partition type
and FreeBSD's sunlabel(8) does not create nor use VTOC information.
For this purpose, new tags have been added to support FreeBSD's
partition types.
just em, there is an igb driver (this follows behavior with our Linux drivers).
All adapters up to the 82575 are supported in em, and new client/desktop support
will continue to be in that adapter.
The igb driver is for new server NICs like the 82575 and its followons.
Advanced features for virtualization and performance will be in this driver.
Also, both drivers now have shared code that is up to the latest we have
released. Some stylistic changes as well.
Enjoy :)
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
implement shm_open(2) and shm_unlink(2) in the kernel:
- Each shared memory file descriptor is associated with a swap-backed vm
object which provides the backing store. Each descriptor starts off with
a size of zero, but the size can be altered via ftruncate(2). The shared
memory file descriptors also support fstat(2). read(2), write(2),
ioctl(2), select(2), poll(2), and kevent(2) are not supported on shared
memory file descriptors.
- shm_open(2) and shm_unlink(2) are now implemented as system calls that
manage shared memory file descriptors. The virtual namespace that maps
pathnames to shared memory file descriptors is implemented as a hash
table where the hash key is generated via the 32-bit Fowler/Noll/Vo hash
of the pathname.
- As an extension, the constant 'SHM_ANON' may be specified in place of the
path argument to shm_open(2). In this case, an unnamed shared memory
file descriptor will be created similar to the IPC_PRIVATE key for
shmget(2). Note that the shared memory object can still be shared among
processes by sharing the file descriptor via fork(2) or sendmsg(2), but
it is unnamed. This effectively serves to implement the getmemfd() idea
bandied about the lists several times over the years.
- The backing store for shared memory file descriptors are garbage
collected when they are not referenced by any open file descriptors or
the shm_open(2) virtual namespace.
Submitted by: dillon, peter (previous versions)
Submitted by: rwatson (I based this on his version)
Reviewed by: alc (suggested converting getmemfd() to shm_open())
machine-independent support for superpages. (The earlier part was
the rewrite of the physical memory allocator.) The remainder of the
code required for superpages support is machine-dependent and will
be added to the various pmap implementations at a later date.
Initially, I am only supporting one large page size per architecture.
Moreover, I am only enabling the reservation system on amd64. (In
an emergency, it can be disabled by setting VM_NRESERVLEVELS to 0
in amd64/include/vmparam.h or your kernel configuration file.)
dump using mechanically generated/extracted debugging output rather than
a simple memory dump. Current sources of debugging output are:
- DDB output capture buffer, if there is captured output to save
- Kernel message buffer
- Kernel configuration, if included in kernel
- Kernel version string
- Panic message
Textdumps are stored in swap/dump partitions as with regular dumps, but
are laid out as ustar files in order to allow multiple parts to be stored
as a stream of sequentially written blocks. Blocks are written out in
reverse order, as the size of a textdump isn't known a priori. As with
regular dumps, they will be extracted using savecore(8).
One new DDB(4) command is added, "textdump", which accepts "set",
"unset", and "status" arguments. By default, normal kernel dumps are
generated unless "textdump set" is run in order to schedule a textdump.
It can be canceled using "textdump unset" to restore generation of a
normal kernel dump.
Several sysctls exist to configure aspects of textdumps;
debug.ddb.textdump.pending can be set to check whether a textdump is
pending, or set/unset in order to control whether the next kernel dump
will be a textdump from userspace.
While textdumps don't have to be generated as a result of a DDB script
run automatically as part of a kernel panic, this is a particular useful
way to use them, as instead of generating a complete memory dump, a
simple transcript of an automated DDB session can be captured using the
DDB output capture and textdump facilities. This can be used to
generate quite brief kernel bug reports rich in debugging information
but not dependent on kernel symbol tables or precisely synchronized
source code. Most textdumps I generate are less than 100k including
the full message buffer. Using textdumps with an interactive debugging
session is also useful, with capture being enabled/disabled in order to
record some but not all of the DDB session.
MFC after: 3 months
define a set of named scripts. Each script consists of a list of DDB
commands separated by ";"s that will be executed verbatim. No higher
level language constructs, such as branching, are provided for:
scripts are executed by sequentially injecting commands into the DDB
input buffer.
Four new commands are present in DDB: "run" to run a specific script,
"script" to define or print a script, "scripts" to list currently
defined scripts, and "unscript" to delete a script, modeled on shell
alias commands. Scripts may also be manipulated using sysctls in the
debug.ddb.scripting MIB space, although users will prefer to use the
soon-to-be-added ddb(8) tool for usability reasons.
Scripts with certain names are automatically executed on various DDB
events, such as entering the debugger via a panic, a witness error,
watchdog, breakpoint, sysctl, serial break, etc, allowing customized
handling.
MFC after: 3 months
captured to a memory buffer for later inspection using sysctl(8), or in the
future, to a textdump.
A new DDB command, "capture", is added, which accepts arguments "on", "off",
"reset", and "status".
A new DDB sysctl tree, debug.ddb.capture, is added, which can be used to
resize the capture buffer and extract buffer contents.
MFC after: 3 months
o Disklabels can have between 8 and 20 partitions (inclusive).
o No device special file is created for the raw partition.
o Switch ia64 to use this backend.
o No support for boot code yet.
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
lock optimized for almost exclusive reader access. (see also rmlock.9)
TODO:
Convert to per cpu variables linkerset as soon as it is available.
Optimize UP (single processor) case.
in the TrustedBSD MAC Framework:
- Add mac_atalk.c and add explicit entry point mac_netatalk_aarp_send()
for AARP packet labeling, rather than using a generic link layer
entry point.
- Add mac_inet6.c and add explicit entry point mac_netinet6_nd6_send()
for ND6 packet labeling, rather than using a generic link layer entry
point.
- Add expliict entry point mac_netinet_arp_send() for ARP packet
labeling, and mac_netinet_igmp_send() for IGMP packet labeling,
rather than using a generic link layer entry point.
- Remove previous genering link layer entry point,
mac_mbuf_create_linklayer() as it is no longer used.
- Add implementations of new entry points to various policies, largely
by replicating the existing link layer entry point for them; remove
old link layer entry point implementation.
- Make MAC_IFNET_LOCK(), MAC_IFNET_UNLOCK(), and mac_ifnet_mtx global
to the MAC Framework rather than static to mac_net.c as it is now
needed outside of mac_net.c.
Obtained from: TrustedBSD Project
This commit includes the following core components:
* sample configuration file for sensorsd
* rc(8) script and glue code for sensorsd(8)
* sysctl(3) doc fixes for CTL_HW tree
* sysctl(3) documentation for hardware sensors
* sysctl(8) documentation for hardware sensors
* support for the sensor structure for sysctl(8)
* rc.conf(5) documentation for starting sensorsd(8)
* sensor_attach(9) et al documentation
* /sys/kern/kern_sensors.c
o sensor_attach(9) API for drivers to register ksensors
o sensor_task_register(9) API for the update task
o sysctl(3) glue code
o hw.sensors shadow tree for sysctl(8) internal magic
* <sys/sensors.h>
* HW_SENSORS definition for <sys/sysctl.h>
* sensors display for systat(1), including documentation
* sensorsd(8) and all applicable documentation
The userland part of the framework is entirely source-code
compatible with OpenBSD 4.1, 4.2 and -current as of today.
All sensor readings can be viewed with `sysctl hw.sensors`,
monitored in semi-realtime with `systat -sensors` and also
logged with `sensorsd`.
Submitted by: Constantine A. Murenin <cnst@FreeBSD.org>
Sponsored by: Google Summer of Code 2007 (GSoC2007/cnst-sensors)
Mentored by: syrinx
Tested by: many
OKed by: kensmith
Obtained from: OpenBSD (parts)
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
a test that assumes that char is signed by default and causes a
warning with GCC 4.2 on PowerPC.
A patch has been sent to the maintainer that addresses this.
Approved by: re (blanket)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
udp6_output() from udp6_output.c to udp6_usrreq.c, matching the UDPv4
structure, and allowing us to remove udp6_output.c.
Reviewed by: bz, gnn
Approved by: re (bmah)
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
- CMT_PF states added (w/sysctl to turn the PF version on)
- sctp_input.c had a missing incr of cookie case when the
auth was bad. This meant a free was called without an
increment to refcnt, added increment like rest of code.
- There was a case, unlikely, when the scope of the destination
changed (this is a TSNH case). In that case, it would not free
the alloc'ed asoc (in sctp_input.c).
- When listed addresses found a colliding cookie/Init, then
the collided upon tcb was not unlocked in sctp_pcb.c
- Add error checking on arguments of sctp_sendx(3) to prevent it from
referencing a NULL pointer.
- Fix an error return of sctp_sendx(3), it was returing
ENOMEM not -1.
- Get assoc id was changed to use the sanctified socket api
method for getting a assoc id (PEER_ADDR_INFO instead of
PEER_ADDR_PARAMS).
- Fix it so a peeled off socket will get a proper error return
if it trys to send to a different address then it is connected to.
- Fix so that select_a_stream can avoid an endless loop that
could hang a caller.
- time_entered (state set time) was not being set in all cases
to the time we went established.
Approved by: re(ken smith)
by removing files from src/sys/coda, and updating include paths in the
new location, kernel configuration, and Makefiles. In one case add
$FreeBSD$.
Discussed with: anderson, Jan Harkes <jaharkes@cs.cmu.edu>
Approved by: re (kensmith)
Repo-copy madness: simon
