This driver hasn't been relevant in almost 15 years. It was for a product on the
shelves for about 6 months in 2003/2004. I've not updated the driver since then,
and have had nobody talk to me about it since maybe 2006 or 2007. It doesn't
implement a standard interface, and can be better done with libusb. All the
action has moved to webcamd for newer, more fully featured hardware. It makes no
appearances in the nycbug dmesg archive.
Relnotes: yes
MFC After: 3 days
I hope to extend this with some more detail in the future but it gives
a good starting point.
Thanks to 0mp for assistance with markup.
Reviewed by: jkoshy
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23982
Document the kernels and worlds targets. Document the TARGETS and EXTRA_TARGETS
variables.
Reviewed by: brooks, bdrewery, emaste (LGTM)
MFC After: 3 days
Differential Revision: https://reviews.freebsd.org/D24212
Add 'WITHOUT_WORLDS' and 'WITHOUT_KERNELS' as aliases for the inconsistently
named MAKE_JUST_KERNELS and MAKE_JUST_WORLDS respectively. I always forget the
MAKE_ part (or is it BUILD_), and it's inconsistent with everything
else. Document the new things, but leave speculation of any eventual MAKE_JUST_*
deprecation out of the manuals and comments.
Reviewed by: brooks, bdrewery, emaste (LGTM)
MFC After: 3 days
Differential Revision: https://reviews.freebsd.org/D24212
for IPv4, enabled only for IPv6, and enabled for IPv4 and IPv6.
The current blackhole detection might classify a temporary outage as
an MTU issue and reduces permanently the MSS. Since the consequences of
such a reduction due to a misclassification are much more drastically
for IPv4 than for IPv6, allow the administrator to enable it for IPv6 only.
Reviewed by: bcr@ (man page), Richard Scheffenegger
Sponsored by: Netflix, Inc.
Differential Revision: https://reviews.freebsd.org/D24219
EINTEGRITY was previously documented as a UFS-specific error for
mount(2). This documents EINTEGRITY as a filesystem-independent error
that may be reported by the backing store of a filesystem.
While here, document EIO as a filesystem-independent error for both
mount(2) and posix_fadvise(2). EIO was previously only documented for
UFS for mount(2).
Reviewed by: mckusick
Suggested by: mckusick
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24168
net.inet.tcp.pmtud_blackhole_detection. Also remove three entries,
which are not sysctl variables but statistic counters for TCP.
Thanks to 0mp@ for suggesting an improvement.
Reviewed by: bcr@
Sponsored by: Netflix, Inc.
Differential Revision: https://reviews.freebsd.org/D24216
- The linked list of cryptoini structures used in session
initialization is replaced with a new flat structure: struct
crypto_session_params. This session includes a new mode to define
how the other fields should be interpreted. Available modes
include:
- COMPRESS (for compression/decompression)
- CIPHER (for simply encryption/decryption)
- DIGEST (computing and verifying digests)
- AEAD (combined auth and encryption such as AES-GCM and AES-CCM)
- ETA (combined auth and encryption using encrypt-then-authenticate)
Additional modes could be added in the future (e.g. if we wanted to
support TLS MtE for AES-CBC in the kernel we could add a new mode
for that. TLS modes might also affect how AAD is interpreted, etc.)
The flat structure also includes the key lengths and algorithms as
before. However, code doesn't have to walk the linked list and
switch on the algorithm to determine which key is the auth key vs
encryption key. The 'csp_auth_*' fields are always used for auth
keys and settings and 'csp_cipher_*' for cipher. (Compression
algorithms are stored in csp_cipher_alg.)
- Drivers no longer register a list of supported algorithms. This
doesn't quite work when you factor in modes (e.g. a driver might
support both AES-CBC and SHA2-256-HMAC separately but not combined
for ETA). Instead, a new 'crypto_probesession' method has been
added to the kobj interface for symmteric crypto drivers. This
method returns a negative value on success (similar to how
device_probe works) and the crypto framework uses this value to pick
the "best" driver. There are three constants for hardware
(e.g. ccr), accelerated software (e.g. aesni), and plain software
(cryptosoft) that give preference in that order. One effect of this
is that if you request only hardware when creating a new session,
you will no longer get a session using accelerated software.
Another effect is that the default setting to disallow software
crypto via /dev/crypto now disables accelerated software.
Once a driver is chosen, 'crypto_newsession' is invoked as before.
- Crypto operations are now solely described by the flat 'cryptop'
structure. The linked list of descriptors has been removed.
A separate enum has been added to describe the type of data buffer
in use instead of using CRYPTO_F_* flags to make it easier to add
more types in the future if needed (e.g. wired userspace buffers for
zero-copy). It will also make it easier to re-introduce separate
input and output buffers (in-kernel TLS would benefit from this).
Try to make the flags related to IV handling less insane:
- CRYPTO_F_IV_SEPARATE means that the IV is stored in the 'crp_iv'
member of the operation structure. If this flag is not set, the
IV is stored in the data buffer at the 'crp_iv_start' offset.
- CRYPTO_F_IV_GENERATE means that a random IV should be generated
and stored into the data buffer. This cannot be used with
CRYPTO_F_IV_SEPARATE.
If a consumer wants to deal with explicit vs implicit IVs, etc. it
can always generate the IV however it needs and store partial IVs in
the buffer and the full IV/nonce in crp_iv and set
CRYPTO_F_IV_SEPARATE.
The layout of the buffer is now described via fields in cryptop.
crp_aad_start and crp_aad_length define the boundaries of any AAD.
Previously with GCM and CCM you defined an auth crd with this range,
but for ETA your auth crd had to span both the AAD and plaintext
(and they had to be adjacent).
crp_payload_start and crp_payload_length define the boundaries of
the plaintext/ciphertext. Modes that only do a single operation
(COMPRESS, CIPHER, DIGEST) should only use this region and leave the
AAD region empty.
If a digest is present (or should be generated), it's starting
location is marked by crp_digest_start.
Instead of using the CRD_F_ENCRYPT flag to determine the direction
of the operation, cryptop now includes an 'op' field defining the
operation to perform. For digests I've added a new VERIFY digest
mode which assumes a digest is present in the input and fails the
request with EBADMSG if it doesn't match the internally-computed
digest. GCM and CCM already assumed this, and the new AEAD mode
requires this for decryption. The new ETA mode now also requires
this for decryption, so IPsec and GELI no longer do their own
authentication verification. Simple DIGEST operations can also do
this, though there are no in-tree consumers.
To eventually support some refcounting to close races, the session
cookie is now passed to crypto_getop() and clients should no longer
set crp_sesssion directly.
- Assymteric crypto operation structures should be allocated via
crypto_getkreq() and freed via crypto_freekreq(). This permits the
crypto layer to track open asym requests and close races with a
driver trying to unregister while asym requests are in flight.
- crypto_copyback, crypto_copydata, crypto_apply, and
crypto_contiguous_subsegment now accept the 'crp' object as the
first parameter instead of individual members. This makes it easier
to deal with different buffer types in the future as well as
separate input and output buffers. It's also simpler for driver
writers to use.
- bus_dmamap_load_crp() loads a DMA mapping for a crypto buffer.
This understands the various types of buffers so that drivers that
use DMA do not have to be aware of different buffer types.
- Helper routines now exist to build an auth context for HMAC IPAD
and OPAD. This reduces some duplicated work among drivers.
- Key buffers are now treated as const throughout the framework and in
device drivers. However, session key buffers provided when a session
is created are expected to remain alive for the duration of the
session.
- GCM and CCM sessions now only specify a cipher algorithm and a cipher
key. The redundant auth information is not needed or used.
- For cryptosoft, split up the code a bit such that the 'process'
callback now invokes a function pointer in the session. This
function pointer is set based on the mode (in effect) though it
simplifies a few edge cases that would otherwise be in the switch in
'process'.
It does split up GCM vs CCM which I think is more readable even if there
is some duplication.
- I changed /dev/crypto to support GMAC requests using CRYPTO_AES_NIST_GMAC
as an auth algorithm and updated cryptocheck to work with it.
- Combined cipher and auth sessions via /dev/crypto now always use ETA
mode. The COP_F_CIPHER_FIRST flag is now a no-op that is ignored.
This was actually documented as being true in crypto(4) before, but
the code had not implemented this before I added the CIPHER_FIRST
flag.
- I have not yet updated /dev/crypto to be aware of explicit modes for
sessions. I will probably do that at some point in the future as well
as teach it about IV/nonce and tag lengths for AEAD so we can support
all of the NIST KAT tests for GCM and CCM.
- I've split up the exising crypto.9 manpage into several pages
of which many are written from scratch.
- I have converted all drivers and consumers in the tree and verified
that they compile, but I have not tested all of them. I have tested
the following drivers:
- cryptosoft
- aesni (AES only)
- blake2
- ccr
and the following consumers:
- cryptodev
- IPsec
- ktls_ocf
- GELI (lightly)
I have not tested the following:
- ccp
- aesni with sha
- hifn
- kgssapi_krb5
- ubsec
- padlock
- safe
- armv8_crypto (aarch64)
- glxsb (i386)
- sec (ppc)
- cesa (armv7)
- cryptocteon (mips64)
- nlmsec (mips64)
Discussed with: cem
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D23677
Now that LLD 10 is out, and required patches have landed, we are now ready
to finally switch away from the ancient in-tree ld.bfd.
Special thanks to Fangrui Song for many hours of work on getting the
32-bit powerpc lld ready for prime-time.
Reviewed by: emaste (earlier revision), jhibbits
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D24111
MIPS was the last arch to use external toolchain by default but uses
in-tree Clang and lld as of r359233, and now no table entries reference
the footnote.
All FreeBSD archs now use an in-tree toolchain - Clang and ELF Tool
Chain everywhere, and lld everywhere but 32-bit PowerPC (which still
uses ld.bfd). No archs use external toolchain by default.
Sponsored by: The FreeBSD Foundation
Now that we have updated the in-tree version of LLVM to 10.0, we have all the
necessary LLVM changes to use Clang+LLD as the default toolchain for MIPS.
Relnotes: yes
Reviewed By: emaste, jhb, brooks, kevans
Differential Revision: https://reviews.freebsd.org/D23204
The devices supported by these drivers are obsolete ISA cards, and the
sync serial protocols they supported are essentially obsolete too.
Sponsored by: The FreeBSD Foundation
Escape sequences like "\n" have to be escaped twice in examples in our
mdoc(7)-based manual pages in order to be displayed properly. The problem
is that otherwise they are interpreted by mdoc(7), which results in:
printf("parent: received '%s'0, buf);
being shown to the user instead of:
printf("parent: received '%s'\n", buf);
Approved by: bcr (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D24056
I intend to document FreeBSD's ELF notes (see review D23982), but start
with a section documenting the format of the note section itself.
Sponsored by: The FreeBSD Foundation
The aim is to reduce the boilerplate needed today to define and
initialize global counters. Also add SI_SUB_COUNTER to the sysinit
ordering.
Reviewed by: kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23977
It does extremely useful things like execute sendmail and spew dubiously
accurate factoids.
From the feedback, it seems like it is an essential utility in a modern unix
and not at all a useless bikeshed. How do those Linux people live without it?
Reverts r358561.
These support outdated or obsolete ISA WAN (T1/E1) sync serial cards,
and these drivers haven't really been touched (other than in tree-wide
sweeps to keep them building) for 15+ years.
Related PCI devices ce and cp are still in the tree, with deprecation
proposed in D23928.
MFC after: 1 week
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Make style.9 read as a current statement of C99 preferences, rather than a
description of ongoing changes to our preferred style. Alsu use the short
form "ISO C99" on the 2nd and later instances rather than repeating the
unwieldy `ISO/IEC 9899:1999 ("ISO C99")` each time.
Reviewed by: cem, imp, jhb, kib
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23648
environ(7) was in AT&T Version 7
ac(8): Add a HISTORY section
sa(8): Add a HISTORY section
sqrt(3): Add the actual sqrt function to the HISTORY section
Obtained from: OpenBSD
Submitted by: gbergling@gmail.com
Approved by: bcr@(mentor)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23693
ACPI Control Method Batteries have a _BIF and/or _BIX object which
provide static properties of the battery. FreeBSD acpi_cmbat module
supported _BIF object only, which was deprecated as of ACPI 4.0.
_BIX is an extended version of _BIF defined in ACPI 4.0 or later.
As of writing, _BIX has two revisions. One is in ACPI 4.0 (rev.0) and
another is in ACPI 6.0 (rev.1). It seems that hardware vendors still
stick to _BIF only or _BIX rev.0 + _BIF for the maximum compatibility.
Microsoft requires _BIX rev.0 for Windows machines, so there are some
laptop machines with _BIX rev.0 only. In this case, FreeBSD does not
recognize the battery information.
After this change, the acpi_cmbat module gets battery information from
_BIX or _BIF object and internally uses _BIX rev.1 data structure as
the primary information store in the kernel. ACPIIO_BATT_GET_BI[FX]
returns an acpi_bi[fx] structure built by using information obtained
from a _BIF or a _BIX object found on the system. The revision number
field can be used to check which field is available. The acpiconf(8)
utility will show additional information if _BIX is available.
Although ABIs of ACPIIO_BATT_* were changed, the existing APIs for
userland utilities are not changed and the backward-compatible ABIs
are provided. This means that older versions of acpiconf(8) can also
work with the new kernel. The (union acpi_battery_ioctl_arg) was
padded to 256 byte long to avoid another ABI change in the future.
A _BIX object with its revision number >1 will be treated as
compatible with the rev.1 _BIX format.
Reviewed by: takawata
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23728
Key and cookie management typically wants to
avoid information leaks by explicitly zeroing
before free. This routine simplifies that by
permitting consumers to do so without carrying
the size around.
Reviewed by: jeff@, jhb@
MFC after: 1 week
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D22790
The function allows to peek at the thread exit status and even see
return value, without joining (and thus finally destroying) the target
thread.
Reviewed by: markj
Sponsored by: The FreeBSD Foundation (kib)
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D23676
It was saved from the initial purge of drivers in fcp-101 due to being
the onboard Ethernet device on a number of sparc64 machines. Now that
sparc64 is gone, it serves little purpose (PCI cards exist, but are rare
and are unlikely to have been deployed outside Sun systems).
MFC after: 3 days
This simplifies the driver's rx fast path as well as the bookkeeping
code that tracks various rx buffer sizes and layouts.
MFC after: 1 week
Sponsored by: Chelsio Communications
The ports framework recently grew support for installing dependencies with
a dedicated target called "install-missing-packages". Let's retire the
carefully constructed one-liner that was used for getting dependencies so
far and use the official ports target instead.
Reviewed by: bcr
Approved by: bcr (mentor)
Differential Revision: https://reviews.freebsd.org/D23485
"*-out" is a complex way of phrasing the fact, and it causes
confusion for people.
Submitted by: debdrup
Approved by: bcr (mentor)
Differential Revision: https://reviews.freebsd.org/D23482
The Parallel Port SCSI adapter was interesting for 100MB ZIP drives, but is no
longer used or maintained. Remove it from the tree.
The Parallel Port microsequencer (microseq.9) is now mostly unused in the tree,
but remains. PPI still refrences it, but doesn't use its full functionality.
Relnotes: Yes
Reviewed by: rgrimes@, Ihor Antonov
Discussed on: arch@
Differential Revision: https://reviews.freebsd.org/D23389
This driver has seen no real changes for almost 20 years. It's for
hardware that's 25 years old. It has no reports of active use, nor
has it been seen in the NYCBug dmesg database at all. Schedule
its removal for 13.0.
Reviewed by: rgrimes@ (earlier version)
Relnote: Yes
MFC After: 3 days
Differential Revision: https://reviews.freebsd.org/D23403
If package-level control is present, we default to using it. Per-core
software control may be enabled by setting the machdep.hwpstate_pkg_ctrl
tunable to "0" in loader.conf(5).
Add a sysctl knob to allow users to re-enable it, and document the knob and
default in cpufreq.4. (While here, add a few unrelated updates to
cpufreq.4.)
It seems that the register value in some hardware simply reflects the
configured P-state. This results in an inadvertent and unintended outcome
where the P-state can only walk down, and then the driver becomes "stuck" in
the slowest possible P-state.
The Linux driver never consults this register, so that's some evidence that
ignoring the contents are relatively harmless.
PR: 234733
Reported by: sigsys AT gmail.com, Erich Dollanksy <freebsd.ed.lists AT
sumeritec.com>
After r355784 the td_oncpu field is no longer synchronized by the thread
lock, so the stack capture interrupt cannot be delievered precisely.
Fix this using a loop which drops the thread lock and restarts if the
wrong thread was sampled from the stack capture interrupt handler.
Change the implementation to use a regular interrupt instead of an NMI.
Now that we drop the thread lock, there is no advantage to the latter.
Simplify the KPIs. Remove stack_save_td_running() and add a return
value to stack_save_td(). On platforms that do not support stack
capture of running threads, stack_save_td() returns EOPNOTSUPP. If the
target thread is running in user mode, stack_save_td() returns EBUSY.
Reviewed by: kib
Reported by: mjg, pho
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23355
The device list hasn't aged well. All these devices are over a decade old. umass
supports thunb drives almost universally, and the list is too long to try to
list here.
Remove some obsolete advice as well. This isn't the place to talk about how to
create FAT filesystems, nor now to mount them. The only advice that's still
useful is the rescanning of a multi-slot flash adapater.
MFC After: 3 days
ng_nat implements NAT for IPv4 traffic only. When connected to an
ng_ether node it erroneously handled IPv6 packets as well.
This change is not sufficient: ng_nat does not do any validation of IP
packets in this mode, even though they have not yet passed through
ip_input().
PR: 243096
Reported by: Robert James Hernandez <rob@sarcasticadmin.com>
Reviewed by: julian
Differential Revision: https://reviews.freebsd.org/D23080
Intel Speed Shift is Intel's technology to control frequency in hardware,
with hints from software.
Let's get a working version of this in the tree and we can refine it from
here.
Submitted by: bwidawsk, scottph
Reviewed by: bcr (manpages), myself
Discussed with: jhb, kib (earlier versions)
With feedback from: Greg V, gallatin, freebsdnewbie AT freenet.de
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D18028
and will slowly transition from /usr/local/man to it. To reflect this remove
the documentation of the manpages being an exception in the layout of /usr/local
Reported by: Dan Nelson <dnelson_1901@yahoo.com> (via IRC)
MFC after: 3 days
Most of the gpio controller cannot configure or get the configuration
of the pin muxing as it's usually handled in the pinctrl driver.
But they can know what is the pinmuxing driver either because they are
child of it or via the gpio-range property.
Add some new methods to fdt_pinctrl that a pin controller can implement.
Some methods are :
fdt_pinctrl_is_gpio: Use to know if the pin in the gpio mode
fdt_pinctrl_set_flags: Set the flags of the pin (pullup/pulldown etc ...)
fdt_pinctrl_get_flags: Get the flags of the pin (pullup/pulldown etc ...)
The defaults method returns EOPNOTSUPP.
Reviewed by: ian, bcr (manpages)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23093
'install' target is invoked.
While here, bump the sample output version name, and explicitly
add the 'obj' target to avoid polluting the src checkout.
Submitted by: Trond Endrestol
PR: 243287 (related)
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (netgate.com)
This enables virtio modules on PowerPC* target.
On PowerPC64, drivers are also kernel builtin.
QEMU currently needs to be patched to in order to work on LE hosts due to known
issue affecting pre-1.0 (legacy) virtio drivers.
The patch was submitted to QEMU mail list by @afscoelho_gmail.com, available at
https://lists.nongnu.org/archive/html/qemu-devel/2020-01/msg01496.html
Submitted by: Alfredo Dal'Ava Junior <alfredo.junior@eldorado.org.br>
Reviewed by: luporl
Differential Revision: https://reviews.freebsd.org/D22833
This provides a specific pointer for users of tap(4) to understand why their
interfaces are losing their addresses, and specifically how to workaround
this if they need different behavior.
This manpage received a .Dd bump earlier today in r35688, so no bump occurs
this time.
Submitted by: sigsys@gmail.com (via IRC)
It's not immediately clear by what mechanism loader(8) will be loading the
preloaded file. Specifically name-drop loader.conf(5) with a pointer to the
module loading section and a description of what the 'name' should look
like, because that certainly isn't clear from the loader.conf(5) standpoint.
The default loader.conf already has a pointer to md(4) where it appears and
the reference to loader.conf in the new version of this manpage should make
it more clear that this is where one should look for information.
Reported by: swills
Reviewed by: swills, manpages (bcr)
With revision by: imp
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D22844
- Garbage collect UMA_ZONE_PAGEABLE & UMA_ZONE_STATIC.
- Move flag VTOSLAB from public to private.
- Introduce public NOTPAGE flag and make HASH private.
- Introduce public NOTOUCH flag and make OFFPAGE private.
- Update man page.
The net effect of this should be to make the contract with clients more
clear. Clients should choose constraints, UMA will figure out how to
implement them. This also breaks the confusing double meaning of
OFFPAGE.
Reviewed by: jeff, markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D23016
- Enable clang and lld as system toolchains.
- Don't use external GCC for universe by default.
- Re-enable riscv64sf since it builds fine with clang + lld.
Reviewed by: emaste, mhorne
Relnotes: yes
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D23089
This allows cheapest DRAM-less NVMe SSDs to use some of host RAM (about
1MB per 1GB on the devices I have) for its metadata cache, significantly
improving random I/O performance. Device reports minimal and preferable
size of the buffer. The code limits it to 1% of physical RAM by default.
If the buffer can not be allocated or below minimal size, the device will
just have to work without it.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
- Drop mention of _LP64. FreeBSD's source generally uses __LP64__
instead of _LP64, and the relevant macros are better covered in the
"Predefined Macros" section.
- Fix a noun/verb disagreement.
Reviewed by: emaste
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22975
- Add missing .Pp after the end of some lists so that there is a blank
line before the subsequent paragraph.
- Use a more typical '-tag' bullet list of the make variable descriptions
at the end. This adds separation between bullets and is the formatting
typically used in manpages for this sort of list.
r355588 Fix WITHOUT_CLANG build
r355646 Revert r354348
r355943 add LDNS build knob dependency on OPENSSL
r356111 Use LLVM as default toolchain for all PowerPC targets
To be used when like rmlocks, except when sleeping for readers needs to be
allowed. See the manpage for more information.
Reviewed by: kib (previous version)
Differential Revision: https://reviews.freebsd.org/D22823
This enables LLVM as the default compiler for powerpc, powerpc64, and
powerpcspe, as well as LLD as the default linker for powerpc64.
LLD is not yet ready for prime time for powerpc and powerpcspe, but work is
continuing on it.
Submitted by: alfredo.junior_eldorado.org.br
Relnotes: YES
Differential Revision: https://reviews.freebsd.org/D20378
srandom(9) is meaningless on SMP systems or any system with, say,
interrupts. One could never rely on random(9) to produce a reproducible
sequence of outputs on the basis of a specific srandom() seed because the
global state was shared by all kernel contexts. As such, removing it is
literally indistinguishable to random(9) consumers (as compared with
retaining it).
Mark random(9) as deprecated and slated for quick removal. This is not to
say we intend to remove all fast, non-cryptographic PRNG(s) in the kernel.
It/they just won't be random(9), as it exists today, in either name or
implementation.
Before random(9) is removed, a replacement will be provided and in-tree
consumers will be converted.
Note that despite the name, the random(9) interface does not bear any
resemblance to random(3). Instead, it is the same crummy 1988 Park-Miller
LCG used in libc rand(3).
_sleep(9), wakeup(9), sleepqueue(9), et al do not dereference or modify the
channel pointers provided in any way; they are merely used as intptrs into a
dictionary structure to match waiters with wakers. Correctly annotate this
such that _sleep() and wakeup() may be used on const pointers without
invoking ugly patterns like __DECONST(). Plumb const through all of the
underlying sleepqueue bits.
No functional change.
Reviewed by: rlibby
Discussed with: kib, markj
Differential Revision: https://reviews.freebsd.org/D22914
off the stack, initialized to default values, and then filled in with
driver-specific values, all without having to worry about the numerous
other fields in the tag. The resulting template is then passed into
busdma and the normal opaque tag object created. See the man page for
details on how to initialize a template.
Templates do not support tag filters. Filters have been broken for many
years, and only existed for an ancient make/model of hardware that had a
quirky DMA engine. Instead of breaking the ABI/API and changing the
arugment signature of bus_dma_tag_create() to remove the filter arguments,
templates allow us to ignore them, and also significantly reduce the
complexity of creating and managing tags.
Reviewed by: imp, kib
Differential Revision: https://reviews.freebsd.org/D22906
- Don't allow an unprivileged user to set the stride. [1]
- Only set the stride under the softc lock.
- Rename the internal fields to accurately reflect their use. Keep
ro_bkt to avoid changing the user API.
- Simplify the implementation. The port index is just sc_seq / stride.
- Document rr_limit in ifconfig.8.
Reported by: Ilja Van Sprundel <ivansprundel@ioactive.com> [1]
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D22857
There are probably bits that are still wrong, but this fixes some
things at least:
- Add named arguments to the functions in crypto(9).
- Add missing algorithms.
- Don't mention arguments that don't exist in crypto_register.
- Add CIOGSESSION2.
- Remove CIOCNFSESSION.
- Clarify some stale language that assumed an fd had only one sesson.
- Note that you have to use CRIOGET and add a note in BUGS lamenting
that one has to use CRIOGET.
- Various other cleanups.
Reviewed by: cem (earlier version)
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D22784
than "/compat/linux". Useful when you have several compat directories
with different Linux versions and you don't want to clash with files
installed by linux-c7 packages.
Reviewed by: bcr (manpages)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D22574
Document the common practices around copyrights with "all rights reserved" in
them as new copyright notices get added.
It's an open question qhether to point people at the fact that since the Berne
convention was ratified, All rights reserved is largely obsolete.
https://en.wikipedia.org/wiki/All_rights_reserved#Obsolescence has the
details. The committer's guide will be revised shortly, and it's likely that's a
better place for this discussion. If not, I'll add a blurb here.
Reviewed by: jhb@, brooks@
Differential Review: https://reviews.freebsd.org/D22800
Contractions cause problems for translators, so s/aren't/are not/ in the one
place this slipped through.
While here, noticed I commited with the date I did the work, not today's
date. Fix that too.
Noticed by: bjk@
Delay the attachment of children, when requested, until after interrutps are
running. This is often needed to allow children to run transactions on i2c or
spi busses. It's a common enough idiom that it will be useful to have its own
wrapper.
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D21465
s/BIT_NAND/BIT_ANDNOT/, and for CPU and DOMAINSET too. The actual
implementation is "and not" (or "but not"), i.e. A but not B.
Fortunately this does appear to be what all existing callers want.
Don't supply a NAND (not (A and B)) operation at this time.
Discussed with: jeff
Reviewed by: cem
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D22791
r355436 moved mitigation sysctls to machdep.mitigations but did not
rationalize the sense of the invidual knobs. Clarify that the old
names remain the canonical way to set these mitigations.
Backwards compatibility will be maintained for the original names
(e.g. hw.ibrs_disable), but not from the interim names
(e.g. machdep.mitigations.ibrs.disable).
Sponsored by: The FreeBSD Foundation
This typedef is the same as timeout_t except that it is in the callout
namespace and header.
Use this typedef in various places of the callout implementation that
were either using the raw type or timeout_t.
While here, add <sys/callout.h> to the manpage.
Reviewed by: kib, imp
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22751
The datasheets for these chips claim the maximum is 921,600, but testing
shows these two higher rates also work (but no rates above 921,600 other
than these two work; these represent dividing the base buad clock by 3 and 2
respectively).
The current vnode layout is not smp-friendly by having frequently read data
avoidably sharing cachelines with very frequently modified fields. In
particular v_iflag inspected for VI_DOOMED can be found in the same line with
v_usecount. Instead make it available in the same cacheline as the v_op, v_data
and v_type which all get read all the time.
v_type is avoidably 4 bytes while the necessary data will easily fit in 1.
Shrinking it frees up 3 bytes, 2 of which get used here to introduce a new
flag field with a new value: VIRF_DOOMED.
Reviewed by: kib, jeff
Differential Revision: https://reviews.freebsd.org/D22715
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
This makes it possible to retrieve per-connection statistical
information such as the receive window size, RTT, or goodput,
using a newly added TCP_STATS getsockopt(3) option, and extract
them using the stats_voistat_fetch(3) API.
See the net/tcprtt port for an example consumer of this API.
Compared to the existing TCP_INFO system, the main differences
are that this mechanism is easy to extend without breaking ABI,
and provides statistical information instead of raw "snapshots"
of values at a given point in time. stats(3) is more generic
and can be used in both userland and the kernel.
Reviewed by: thj
Tested by: thj
Obtained from: Netflix
Relnotes: yes
Sponsored by: Klara Inc, Netflix
Differential Revision: https://reviews.freebsd.org/D20655
FDT bindings document for gpio-i2c devices.
Using the gpio_pin_* functions to acquire/release/manipulate gpio pins
removes the constraint that both gpio pins must belong to the same gpio
controller/bank, and that the gpioiic instance must be a child of gpiobus.
Removing those constraints allows the driver to be fully compatible with
the modern dts bindings for a gpio bitbanged i2c bus.
For hinted attachment, the two gpio pins still must be on the same gpiobus,
and the device instance must be a child of that bus. This preserves
compatibility for existing installations that have use gpioiic(4) with hints.
It was introduced by r290122, but no documentation was provided.
This is taken from https://reviews.freebsd.org/D21798, since it
is not related to the feature added there.
Submitted by: Richard Scheffenegger
MFC after: 1 week
Generally, it's preferred that an application fork/setsid if it doesn't want
to keep its controlling TTY, but it could be that a debugger is trying to
steal it instead -- so it would hook in, drop the controlling TTY, then do
some magic to set things up again. In this case, TIOCNOTTY is quite handy
and still respected by at least OpenBSD, NetBSD, and Linux as far as I can
tell.
I've dropped the note about obsoletion, as I intend to support TIOCNOTTY as
long as it doesn't impose a major burden.
Reviewed by: bcr (manpages), kib
Differential Revision: https://reviews.freebsd.org/D22572
In r353734 the use of the page caches was limited to systems with a
relatively large amount of RAM per CPU. This was to mitigate some
issues reported with the system not able to keep up with memory pressure
in cases where it had been able to do so prior to the addition of the
direct free pool cache. This change re-enables those caches.
The change modifies uma_zone_set_maxcache(), which was introduced
specifically for the page cache zones. Rather than using it to limit
only the full bucket cache, have it also set uz_count_max to provide an
upper bound on the per-CPU cache size that is consistent with the number
of items requested. Remove its return value since it has no use.
Enable the page cache zones unconditionally, and limit them to 0.1% of
the domain's pages. The limit can be overridden by the
vm.pgcache_zone_max tunable as before.
Change the item size parameter passed to uma_zcache_create() to the
correct size, and stop setting UMA_ZONE_MAXBUCKET. This allows the page
cache buckets to be adaptively sized, like the rest of UMA's caches.
This also causes the initial bucket size to be small, so only systems
which benefit from large caches will get them.
Reviewed by: gallatin, jeff
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D22393
Add bit_ffs_area_at and bit_ffc_area_at functions for searching a bit
string for a sequence of contiguous set or unset bits of at least the
specified size.
The bit_ffc_area function will be used by the Intel ice driver for
implementing resource assignment logic using a bitstring to represent
whether or not a given index has been assigned or is currently free.
The bit_ffs_area, bit_ffc_area_at and bit_ffs_area_at functions are
implemented for completeness.
I'd like to add further test cases for the new functions, but I'm not
really sure how to add them easily. The new functions depend on specific
sequences of bits being set, while the bitstring tests appear to run for
varying bit sizes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: asomers@, erj@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D22400
Each boot, regenerate /var/run/os-release based on the currently running
system. Create a /etc/os-release symlink pointing to this file (so that this
doesn't create a new reason /etc can not be mounted read-only).
This is compatible with what other systems do and is what the sysutil/os-release
port attempted to do, but in an incomplete way. Linux, Solaris and DragonFly all
implement this natively as well. The complete standard can be found at
https://www.freedesktop.org/software/systemd/man/os-release.html
Moving this to the base solves both the non-standard location problem with the
port, as well as the lack of update of this file on system update.
Bump __FreeBSD_version to 1300060
PR: 238953
Differential Revision: https://reviews.freebsd.org/D22271
Mount the UEFI ESP on /boot/efi. No current system uses this by default, but
there are many ad-hoc schemes that do this in /efi or /esp or /uefi and adding a
new directory at the top-level would have a much higher likelihood of
collision. Document this in /etc/mtree/BSD.root.mtree and create EFIDIR and
related variables in bsd.own.mk.
Differential Revision: https://reviews.freebsd.org/D21344
r354289 armv6: Switch to LLD by default
r354290 Take arm.arm (armv5) out of universe
r354348 armv6, armv7: Switch to llvm-libunwind by default
r354660 Enable the RISC-V LLVM backend by default.
as well as lib32 changes
Sponsored by: The FreeBSD Foundation
This driver was largely rewritten in 2015 (svn r235911) but the man page was
never updated to match.
Reviewed by: trasz
MFC after: 2 weeks
Sponsored by: Axcient
Differential Revision: https://reviews.freebsd.org/D22339
This driver allows to usage of the paravirt SCSI controller
in VMware products like ESXi. The pvscsi driver provides a
substantial performance improvement in block devices versus
the emulated mpt and mps SCSI/SAS controllers.
Error handling in this driver has not been extensively tested
yet.
Submitted by: vbhakta@vmware.com
Relnotes: yes
Sponsored by: VMware, Panzura
Differential Revision: D18613
Disable the use of executable 2M page mappings in EPT-format page
tables on affected CPUs. For bhyve virtual machines, this effectively
disables all use of superpage mappings on affected CPUs. The
vm.pmap.allow_2m_x_ept sysctl can be set to override the default and
enable mappings on affected CPUs.
Alternate approaches have been suggested, but at present we do not
believe the complexity is warranted for typical bhyve's use cases.
Reviewed by: alc, emaste, markj, scottl
Security: CVE-2018-12207
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D21884
Previously ntb_transport(4) required at least 6 scratchpad registers,
plus 2 more for each additional memory window. That is too much for some
configurations, where several drivers have to share resources of the same
NTB hardware. This patch introduces new compact version of the protocol,
requiring only 3 scratchpad registers, plus one more for each additional
memory window. The optimization is based on fact that neither of version,
number of windows or number of queue pairs really need more then one byte
each, and window sizes of 4GB are not very useful now. The new protocol
is activated automatically when the configuration is low on scratchpad
registers, or it can be activated explicitly with loader tunable.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Address Lookup Table (A-LUT) being enabled allows to specify separate
translation for each 1/128th or 1/256th of the BAR2. Previously it was
used only to limit effective window size by blocking access through some
of A-LUT elements. This change allows A-LUT elements to also point
different memory locations, providing to upper layers several (up to 128)
independent memory windows. A-LUT hardware allows even more flexible
configurations than this, but NTB KPI have no way to manage that now.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
The man page incorrectly described the use of the"len" argument, which
is updated to the number of bytes copied and not reduced by the number
of bytes copied.
This is a content change.
Thanks to bapt, bz, cem, woodsb02, Neel Chauhan and Salvador Martínez
Mármol for helping test the initial 9000-series support.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
GCC 4.2.1 is being removed before FreeBSD 13, as are some other
components required by FreeBSD/sparc64. Contemporary GCC does not build
and there is currently no indication that anyone is going to address
these issues.
PR: 228919, 233405, 236839, 239851
Postings were sent to -arch@ on 2019/09/13 and 2019/10/01, proposing and
confirming a removal of these scripts on 2019/10/31, due to significant work
needed to bring this into the modern world and nobody having done this work
in the past couple of years. No objections or proposed work was raised in
response to these postings. The tinyware may see a resurrection into a
separate repo for archival purposes if any users of it show interest in
doing so.
MFC after: never
The valectl(4) program is used to manage vale(4) switches.
Add it to the system commands so that it can be used right away.
This program was previously called vale-ctl, and stored in
tools/tools/netmap
Reviewed by: hrs, bcr, lwhsu, kevans
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22146
The source part of the review will be addressed in a different way.
Reviewed by: emaste, brooks
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D21492
Summary:
Historically, we have built toolchain components such as cc, ld, etc as
statically linked executables. One of the reasons being that you could
sometimes save yourself from botched upgrades, by e.g. recompiling a
"known good" libc and reinstalling it.
In this day and age, we have boot environments, virtual machine
snapshots, cloud backups, and other much more reliable methods to
restore systems to working order. So I think the time is ripe to flip
this default, and link the toolchain components dynamically, just like
almost all other executables on FreeBSD.
Maybe at some point they can even become PIE executables by default! :)
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D22061
Notices appear both in picobsd(8) (near the top for easy notice) and are
also printed to stderr on every invocation of picobsd for visibility.
The tentative date for removal is October 31st, as no volunteers have
stepped forward at all from postings to -arch@ at least.
No objection from: -arch@
MFC after: 3 days
The change is for the example in textdump.4 and the default ddb.conf.
First of all, doadump now requires an argument and it won't do a
textdump if the argument is not 'true'.
And 'textdump dump' is more idiomatic anyway.
For what it's worth, ddb 'dump' command seems to always request a vmcore
dump even if a textdump was requested earlier, e.g., by 'textdump set'.
Finally, ddb 'call' command is not documented.
MFC after: 2 weeks
NetGDB(4) is a component of a system using a panic-time network stack to
remotely debug crashed FreeBSD kernels over the network, instead of
traditional serial interfaces.
There are three pieces in the complete NetGDB system.
First, a dedicated proxy server must be running to accept connections from
both NetGDB and gdb(1), and pass bidirectional traffic between the two
protocols.
Second, the NetGDB client is activated much like ordinary 'gdb' and
similarly to 'netdump' in ddb(4) after a panic. Like other debugnet(4)
clients (netdump(4)), the network interface on the route to the proxy server
must be online and support debugnet(4).
Finally, the remote (k)gdb(1) uses 'target remote <proxy>:<port>' (like any
other TCP remote) to connect to the proxy server.
The NetGDB v1 protocol speaks the literal GDB remote serial protocol, and
uses a 1:1 relationship between GDB packets and sequences of debugnet
packets (fragmented by MTU). There is no encryption utilized to keep
debugging sessions private, so this is only appropriate for local
segments or trusted networks.
Submitted by: John Reimer <john.reimer AT emc.com> (earlier version)
Discussed some with: emaste, markj
Relnotes: sure
Differential Revision: https://reviews.freebsd.org/D21568
Loosen requirements for connecting to debugnet-type servers. Only require a
destination address; the rest can theoretically be inferred from the routing
table.
Relax corresponding constraints in netdump(4) and move ifp validation to
debugnet connection time.
Submitted by: John Reimer <john.reimer AT emc.com> (earlier version)
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D21482
Add a 'X -s <server> -c <client> [-g <gateway>] -i <interface>' subroutine
to the generic debugnet code. The imagined use is both netdump, shown here,
and NetGDB (vaporware). It uses the ddb(4) lexer, with some new extensions,
to parse out IPv4 addresses.
'Netdump' uses the generic debugnet routine to load a configuration and
start a dump, without any netdump configuration prior to panic.
Loosely derived from work by: John Reimer <john.reimer AT emc.com>
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D21460
