even if kernel routing table already has a route to the address in question
installed by some routing daemon (PR 223129).
Also, allow loopback route deletion when stopping a VIMAGE jail (PR 222647).
PR: 222647, 223129
Reviewed by: gnn
Approved by: avg (mentor), mav (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D12747
TARGET_ABI/TARGET_CPU in Makefile.inc1 sets the ABI to gnueabihf, which affects
the clang lookup path per getArchNameForCompilerRTLib(..) in
contrib/llvm/tools/clang/lib/Driver/ToolChain.cpp .
This is a follow up to r324873.
PR: 222925
Otherwise an orderly shutdown will initiate a watchdog that will cause
a 7 minute delayed reboot *by default*, In the freebsd.org cluster's case
this often worked out be a surprise reboot a minute or two after the
machine came back up.
As of r325320 posix_fallocate returns EINVAL on ZFS to indicate that
the underlying filesystem does not support this operation, per
POSIX.1-2008. Document this case in the man page.
MFC after: 20 days
MFC with: r325320
Sponsored by: The FreeBSD Foundation
The Freescale SATA controller has many similarities to AHCI controllers, so
this driver is a heavily modified AHCI driver. Currently it seems to only
do SATA 1.0 speeds (~100-150MB/s), so there is still room for improvement.
Still to be done:
* Address erratum SATA-A-006187 -- Spread Spectrum Support (intermittent
non-recoverable transient data integrity error seen when SSC enabled).
* Linux doesn't read the log page as it hangs on the P1022. See if that's
applicable to this, and address accordingly.
* Try to determine what's holding back performance, and address it.
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D6071
As of r325320 posix_fallocate on a ZFS filesystem returns EINVAL to
indicate that the operation is not supported. (I think this is a strange
choice of errno on the part of POSIX.)
PR: 223383, 223440
Reported by: Mark Millard
Tested by: Mark Millard
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
The cleanobj target will not really remove the OBJDIR in this case,
it will only remove the OBJDIR if only clean targets are ran.
Sponsored by: Dell EMC Isilon
When AUTO_OBJ is enabled this change becomes redundant with the auto.obj.mk
check added in r325404. However, it is possible that new code is added
at some point between src.sys.obj.mk and auto.obj.mk that disables AUTO_OBJ.
That could leave make with a bogus and unsafe .OBJDIR in some cases.
Sponsored by: Dell EMC Isilon
auto.obj.mk is loaded before the Makefile which may have NO_OBJ set inside of
it. In that case we can't avoid creating the OBJDIR but we do need to avoid
using it. Fixing .OBJDIR in bsd.init.mk at least fixes all of the build .mk
files to have a proper .OBJDIR. It does not fix the Makefile itself but
usually if they have NO_OBJ set they are not inspecting ${.OBJDIR} anyhow.
It is ideal to only have this in bsd.init.mk and to remove it from bsd.obj.mk,
but then bsd.obj.mk would need to include bsd.init.mk. Doing something like
that would require more testing. It has been proposed that bsd.obj.mk not be
included directly but it has been possible for too long to do so to change it
at this point.
Note too that it may make sense to fix .OBJDIR even when AUTO_OBJ is not
enabled but the historical behavior has always been that NO_OBJ just avoids
running 'make obj', so .OBJDIR should already be .CURDIR.
Also while NO_OBJ seems like it should be removed at this point, it is not
always possible to fix Makefiles to properly use an .OBJDIR. The cost of
keeping NO_OBJ support is minimal.
Sponsored by: Dell EMC Isilon
This problem was caused by r325329 and r325350.
For the release(7) targets, some will run mm-mtree.sh which itself runs make
with a MAKEOBJDIRPREFIX. The execution of that script leaks OBJROOT,
MAKEOBJDIR, and MAKELEVEL=1 in the environment. This causes the mm-mtree makes
to not do some basic setup of OBJROOT and only use this special
MAKEOBJDIRPREFIX case which fails to empty out MAKEOBJDIRPREFIX for further
nested makes, such as a tree walk. If that tree walk sets OBJROOT/OBJTOP such
as r325329 is doing, then the wrong OBJDIRs end up being used due to the
unemptied MAKEOBJDIRPREFIX being preferred over the proper MAKEOBJDIR.
Pointyhat to: bdrewery
Sponsored by: Dell EMC Isilon
Under certain traffic pattern awg driver does not recover from TX queue
full condition. The actual source of the problem is not identified yet
but jmcneill@ agreed that bumping TX_MAX_SEGS to 20 is OK as a workaround
for the problem (NetBSD has it set to 128).
Also add some diagnostic printfs to prevent silent failure of bus_dma
functions in the future
PR will be kept open until root cause of the issue is identified and fixed
PR: 219927
Submitted by: Tom Vijlbrief <tvijlbrief@gmail.com>
Approved by: jmcneill
MFC after: 2 weeks
Forcing MK_AUTO_OBJ to no is not really needed since bsd.obj.mk is protected
against 'rm -rf ${.CURDIR}' already. It was also flawed as if MK_AUTO_OBJ=yes
was in the .MAKEOVERRIDES already then it just remained on.
Sponsored by: Dell EMC Isilon
If for any reason we cannot set .OBJDIR==_objdir as desired
use .CURDIR so that at least the classic
.if ${.OBJDIR} != ${.CURDIR}
works and dangerous misstakes can be avoided.
Reviewed by: bdrewery
respected.
Please notice that libcasper is already in ObsoleteFiles so we don't add it
again.
Reported by: Herbert J. Skuhra <herbert@mailbox.org>
Reviewed by: bdrewery@
Differential Revision: https://reviews.freebsd.org/D12918
costly PCI config space operations that slows down systems without the
hardware.
Many thanks to HighPoint for continued support of FreeBSD!
Submitted by: Steve Chang
Reported by: cperciva
MFC after: 2 weeks
We already pass -many to the assembler, and -me500 drops 64-bit instruction
handling, for some reason only breaking module building for 64-bit kernels.
Additionally, build with CTF for dtrace.
NO_OBJ has a very specific meaning in sub-directories in that no object
directory will be made. If a user wanted to skip the 'make obj' phase then
passing -DNO_OBJ would break all sub-directories from building properly. Using
NO_OBJ internally also causes issue with NO_OBJ handling being added in
share/mk/bsd.init.mk soon.
Sponsored by: Dell EMC Isilon
ubldr is the non-pie version of ubldr.bin, do not install two
copies of the same binary. This will allow us to remove ubldr
in the future.
All the u-boot ports know how to load ubldr.bin
Reviewed by: gjb (earlier version)
