Add a drain function for struct sysctl_req, and use it for a variety
of handlers, some of which had to do awkward things to get a large
enough SBUF_FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing
NUL byte. This behaviour was preserved, though it should not be
necessary.
Reviewed by: phk (original patch)
unexpected things in copyout(9) and so wiring the user buffer is not
sufficient to perform a copyout(9) while holding a random mutex.
Requested by: nwhitehorn
handlers, some of which had to do awkward things to get a large enough
FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing NUL
byte. This behaviour was preserved, though it should not be necessary.
Reviewed by: phk
10G cards. 1G cards are x4 only.
- Use constants from pcireg.h for reading the current link width.
- Use pci_set_max_read_req() rather than implementing it by hand.
Reviewed by: np
MFC after: 1 week
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.
MFC after: 1 month
The T3 ASIC can provide an incoming packet's timestamp instead of its RSS hash.
The timestamp is just a counter running off the card's clock. With a 175MHz
clock an increment represents ~5.7ns and the 32 bit value wraps around in ~25s.
# sysctl -d dev.cxgbc.0.pkt_timestamp
dev.cxgbc.0.pkt_timestamp: provide packet timestamp instead of connection hash
# sysctl -d dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: core clock frequency (in KHz)
# sysctl dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: 175000
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.
- Use 16k jumbo clusters only on offload capable cards by default.
- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.
- Slightly better freelist size calculation.
- Fix nmbjumbo4 typo, remove unneeded global variables.
MFC after: 3 days
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.
This fixes a panic when running tcpdump on a cxgb interface.
- introduce drbr_needs_enqueue that returns whether the interface/br needs
an enqueue operation: returns true if altq is enabled or there are
already packets in the ring (as we need to maintain packet order)
- update all drbr consumers
- fix drbr_flush
- avoid using the driver queue (IFQ_DRV_*) in the altq case as the
multiqueue consumer does not provide enough protection, serialize altq
interaction with the main queue lock
- make drbr_dequeue_cond work with altq
Discussed with: kmacy, yongari, jfv
MFC after: 4 weeks
the leading underscores since they are now implemented.
- Implement the tcpi_rto and tcpi_last_data_recv fields in the tcp_info
structure.
Reviewed by: rwatson
MFC after: 2 weeks
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
