short, it gets filled uop to its length. This matches the getdomainname
and gethostname manual pages.
(getbootfile also uses this function and I think it should have the same
behaviour)
This also fixes a bug with keyinit where the seed was not saved in
/etc/skeykeys. So S/Key should be fully functional again.
Reviewed by:
Submitted by:
Obtained from:
is supposed to work except "media removal" (shutting down the vn driver)
while some partitions are open.
Fix some errnos: return ENOTTY, not ENXIO for unknown ioctls; return
ENODEV, not ENXIO for the unsupported dump operation.
the APM-bios.
This stabilizes a couple of APM bioses quite a bit.
They all make the mistake of going into 16-bit mode, without clearing the
top half of the 32bit registers.
Later they do a
| movw %si,$0x7331
| movw %ax,0x6(%si)
or something along those lines and crash and burn, because their segment
is already relocated, so adding 0xf0171ce9 to the base of it is bad news.
At least SystemSoft is guilty of this bummer.
Voxware hackers should feel free to work on this some more, it's by no means
a perfect product.
(I have patches for GUS users running 2.x to run their GUS with bidirectional
DMA (talk while listening. All other soundboards must use push-to-talk until
people learn to build real hardware).
Submitted by: amancio hasty & paul traina
and one set by the protocol family. Also add another parameter to
rtalloc1() to allow for any interface flags to be ignored; currently
this is only useful for RTF_PRCLONING. Get rid of rt_prflags and re-unite
with rt_flags. Add T/TCP ``route metrics''.
NB: YOU MUST RECOMPILE `route' AND OTHER RELATED PROGRAMS AS A RESULT OF
THIS CHANGE.
This also adds a new interface parameter, `ifi_physical', which will
eventually replace IFF_ALTPHYS as the mechanism for specifying the
particular physical connection desired on a multiple-connection card.
NB: YOU MUST RECOMPILE `ifconfig' AND OTHER RELATED PROGRAMS AS A RESULT OF
THIS CHANGE.
DE_UPDATE was confused with DE_MODIFIED in some places (they do have
confusing names). Handle them exactly the same as IN_UPDATE and
IN_MODIFIED. This fixes chmod() and chown() clobbering the mtime
and other bugs.
DE_MODIFIED was set but not used.
Parenthesize macro args.
DE_TIMES() now takes a timeval arg instead of a timespec arg. It was
stupid to use a macro for speed and do unused conversions to prepare
for the macro.
Restore the left shifting of the DOS seconds count by 1. It got
lost among the shifts for the bitfields, so DOS seconds counts
appeared to range from 0 to 29 seconds (step 1) instead of 0 to 58
seconds (step 2).
Actually use the passed-in mtime in deupdat() as documented so that
utimes() works.
Change `extern __inline's to `static inline's so that msdosfs_fat.o
can be linked when it is compiled without -O.
Remove faking of directory mtimes to always be the current time. It's
more surprising for directory mtimes to change when you read the
directories than for them not to change when you write the directories.
This should be controlled by a mount-time option if at all.
Improve hzto():
Round up instead of down and then add 1 tick. This fixes sleep(1)
sometimes sleeping for < 1 second and usleep(10000) sometimes sleeping
for as little as 1 usec + syscall time.
Don't do all the calculations at splhigh().
Don't depend on `tick' being a multiple of 1000.
Don't lose accuracy for `sec' between 0x7fffffff / 1000 - 1000 and
0x7fffffff / hz.
Don't assume that longs are 32 bits or that ints have the same size as
longs.
Prepare for disk slices - more macros for handling disk device numbers,
version of readdisklabel() without DOS goop.
Clean up prototypes.
Uniformize idempotency ifdef.
diskslice.h:
New file.
dkbad.h:
Define more magic numbers.
Declare internalized version of dkbad struct and functions to operate on it.
Uniformize idempotency ifdef.
worked in the past only because of good fortune. Anyway, use the contig alloc
routine I wrote awhile ago (vm_page_alloc_contig) for the sound code to do
this allocation. Also, specify read+write on the permissions to pmap_enter().
Specifying just read can have unexpected consquences.
of returning EINVAL since something may depend on them being broken.
Allowing negative limits caused bugs almost everywhere. The recent
fixes for MAXSSIZ checked the limits too late to stop anyone defeating
limits set by root...
<string.h> isn't supposed to be used by the kernel.
cronix.h is <machine/cronix.h>, not "cronyx.h" (ambiguous) or
<sys/cronyx.h> (nonexistent; caused compile to fail).
cxreg.h is <i386/isa/cxreg.h>, not "cxreg.h".
<i386/isa/cpufunc.h> shouldn't be included directly; it is always
included by <sys/systm.h>.
<i386/include/*.h> is <machine/*.h>
<systm.h> is <sys/systm.h>.
<kernel.h> is <sys/kernel.h>.
<bpfilter.h> is "bpfilter.h". It really is in the current directory.
>Description:
If a process attempts to open a floppy tape device when the
device has been configured in the kernel, but did not probe and attach
on bootup, then a panic will occur.
[Review: The current ft situation is a crock, and this only bandaids
an earlier wound inflicted by making the attach conditional. This urgently
requires a review]
Submitted by: gene
Keep track of interrupt nesting level. It is normally 0
for syscalls and traps, but is fudged to 1 for their exit
processing in case they metamorphose into an interrupt
handler.
i386/genassym.c;
Remove support for the obsolete pcb_iml and pcb_cmap2.
Add support for pcb_inl.
i386/swtch.s:
Fudge the interrupt nesting level across context switches and in
the idle loop so that the work for preemptive context switches
gets counted as interrupt time, the work for voluntary context
switches gets counted mostly as system time (the part when
curproc == 0 gets counted as interrupt time), and only truly idle
time gets counted as idle time.
Remove obsolete support (commented out and otherwise) for pcb_iml.
Load curpcb just before curproc instead of just after so that
curpcb is always valid if curproc is. A few more changes like
this may fix tracing through context switches.
Remove obsolete function swtch_to_inactive().
include/cpu.h:
Use the new interrupt nesting level variable to implement a
non-fake CLF_INTR() so that accounting for the interrupt state
works.
You can use top, iostat or (best) an up to date systat to see
interrupt overheads. I see the expected huge interrupt overheads
for ISA devices (on a 486DX/33, about 55% for an IDE drive
transferring 1250K/sec and the same for a WD8013EBT network card
transferring 1100K/sec). The huge interrupt overheads for serial
devices are unfortunately normally invisible.
include/pcb.h:
Remove the obsolete pcb_iml and pcb_cmap2. Replace them by
padding to preserve binary compatibility.
Use part of the new padding for pcb_inl.
isa/icu.s:
isa/vector.s:
Keep track of interrupt nesting level.
used as an address value. Then all comparisons should be done unsigned
and not signed. Fix it with a typecast of u_quad_t.
Error can be demonstrated with the current bash in port, do a
ulimit -s unlimited and the machine hangs. bash delivers through
an internal error a large negative value for the stacksize, the
comparison saw this smaller than MAXSSIZ and then tried to expand
the stack to this size.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.
This also includes a new version of the pre-generated file <ugh>
Obtained from: John Aycock (aycock@cpsc.ucalgary.ca) and myself
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
This should have been disabled for some time, but I had screwed up ...
This made spurious values appear for fd0 in systat, when there was
NCR SCSI activity.
comconsole will behave as expected. The true problem should be fixed
instead, Bruce' comment for this:
>Anyway, i found the reason for my problems: somehow, ICRNL isn't in
>effect at `userconfig' time (but only for comconsole?), hence only
ICRNL doesn't apply to cngetc(). cnputc() unconditionally does the
equivalent of ONLCR; perhaps cngetc() should unconditionally do the
equivalent of ICRNL. Ddb must be checking for CR. Userconfig only
checks for NL. Userconfig works with syscons because pccngetc()
does the conversion. This is probably the wrong place to do it.
Allow chown() to return success if the gid isn't changed even if
the gid is not the caller's. Such gids are normal for files created
in world-writable directories sucj as /tmp. This "fixes" annoying
error messages for mv'ing files created in /tmp to another file
system. mv still preserves the foreign gid of /tmp, but now does
it silently.
operation of each clist. Limit the growth of each clist. Clists
can only grow larger than the reserved minimum if there are free
cblocks in a shared pool. The size of this pool is now fixed
(this could be improved). The reserved and maximum sizes are more
carefully allocated for slip and ppp, depending on the mtu. A maximum
MTU of 16384 is now enforced for ppp.
1. The pageout daemon used to block under certain
circumstances, and we needed to add new functionality
that would cause the pageout daemon to block more often.
Now, the pageout daemon mostly just gets rid of pages
and kills processes when the system is out of swap.
The swapping, rss limiting and object cache trimming
have been folded into a new daemon called "vmdaemon".
This new daemon does things that need to be done for
the VM system, but can block. For example, if the
vmdaemon blocks for memory, the pageout daemon
can take care of it. If the pageout daemon had
blocked for memory, it was difficult to handle
the situation correctly (and in some cases, was
impossible).
2. The collapse problem has now been entirely fixed.
It now appears to be impossible to accumulate unnecessary
vm objects. The object collapsing now occurs when ref counts
drop to one (where it is more likely to be more simple anyway
because less pages would be out on disk.) The original
fixes were incomplete in that pathological circumstances
could still be contrived to cause uncontrolled growth
of swap. Also, the old code still, under steady state
conditions, used more swap space than necessary. When
using the new code, users will generally notice a
significant decrease in swap space usage, and theoretically,
the system should be leaving fewer unused pages around
competing for memory.
Submitted by: John Dyson
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
1) make #includes correct
2) fix bugs in address check macros
3) fixed bugs in, and enabled, recopy if heavily fragmented code
4) moved call to bpf tap to be before enqueing packet (probably gratuitous)
5) fixed bug that caused "abnormal interrupt" at boot time/first use
6) added support for reading Zynx address ROM
7) fixed bug that caused broadcasts to not work shortly after booting (only
manifested if not using multicast - e.g. not in FreeBSD 2.0)
8) fixed spelling errors in comments
Submitted by: Matt Thomas
Subject: Mea culpa -- small fix for netboot fixes
In accordance with the unavoidable principle sof Murphy's Law, I discovered
that the fixes I recently contributed for the netboot code had some small
flaws in them. Two of them were just typos and had no effect on how the
program functioned. The other one was a missing line from the rootopts and
swapopts functions I created in bootmenu.c, which was supposed to initialize
the NFS sotype flag. It defaults to UDP, and you can change it to TCP with
the rootopts or swapopts commands, but then you can't change it back again.
I originally had a line at the top of each function to reinitialize this
flag, but somehow it got lost in the shuffle, probably because I don't
actually have a need for that flag yet.
Submitted by: wpaul
That was the good news. The bad news is that bad144 is a proper mess,
and I don't have time to fix it now, so you will probably not be able to
use it anyway.
Sorry guys, go out and buy a 100Mb IDE drive and a paddleboard :-(
If somebody wants to pick up on this: bad144 needs to learn how to
stay inside our slice of the disk. That's the trick.
