didn't already have them. This is because the ternary expression will
return int, due to the Usual Arithmetic Conversions. Such casts are not
needed for the 32 and 64 bit variants.
While here, add additional parentheses around the x86 variant, to
protect against unintended consequences.
MFC after: 2 weeks
- Remove extern "C". There are no functions with external linkage here. [1]
- Rename bswapNN_const(x) to bswapNN_gen(x) to indicate that these macros
are generic implementations that can take non-constant arguments. [1]
- Split up __GNUCLIKE_ASM && __GNUCLIKE_BUILTIN_CONSTANT_P and deal with
each separately.
- Replace _LP64 with __amd64__ because asm instructions are machine
dependent, not ABI dependent.
Submitted by: bde [1]
Reviewed by: bde
amd64/i386/pc98 ptrace.h with stubs.
For amd64 PT_GETXSTATE and PT_SETXSTATE have been redefined to match the
i386 values. The old values are still supported but should no longer be
used.
Reviewed by: kib
long for specifying a boundary constraint.
- Change bus_dma tags to use bus_addr_t instead of bus_size_t for boundary
constraints.
These allow boundary constraints to be fully expressed for cases where
sizeof(bus_addr_t) != sizeof(bus_size_t). Specifically, it allows a
driver to properly specify a 4GB boundary in a PAE kernel.
Note that this cannot be safely MFC'd without a lot of compat shims due
to KBI changes, so I do not intend to merge it.
Reviewed by: scottl
Enforce a boundary of no more than 4GB - transfers crossing a 4GB
boundary can lead to data corruption due to PCIe limitations. This
change is a less-intrusive workaround that can be quickly merged back
to older branches; a cleaner implementation will arrive in HEAD later
but may require KPI changes.
This change is based on a suggestion by jhb@.
Reviewed by: scottl, jhb
Sponsored by: Sandvine Incorporated
MFC after: 3 days
amd64/i386/pc98 endian.h with stubs.
In __bswap64_const(x) the conflict between 0xffUL and 0xffULL has been
resolved by reimplementing the macro in terms of __bswap32(x). As a side
effect __bswap64_var(x) is now implemented using two bswap instructions on
i386 and should be much faster. __bswap32_const(x) has been reimplemented
in terms of __bswap16(x) for consistency.
APIC is not found.
- Don't panic if lapic_enable_cmc() is called and the APIC is not enabled.
This can happen due to booting a kernel with APIC disabled on a CPU that
supports CMCI.
- Wrap a long line.
- Actually increment ndomain when building our list of known domains
so that we can properly renumber them to be 0-based and dense.
- If the number of domains exceeds the configured maximum (VM_NDOMAIN),
bail out of processing the SRAT and disable NUMA rather than hitting an
obscure panic later.
- Don't bother parsing the SRAT at all if VM_NDOMAIN is set to 1 to
disable NUMA (the default).
Reported by: phk (2)
MFC after: 1 week
Where i386/bios/apm.c requires no per-descriptor state, the ACPI version
of these device do. Instead of using hackish clone lists that leave
stale device nodes lying around, use the cdevpriv API.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
existing phys_avail[] table. If a hw.physmem setting causes a memory
domain to not be present in phys_avail[], the SRAT table will now be
ignored rather than triggering a panic when a CPU in the missing domain
tries to allocate a page.
MFC after: 1 week
If a selinfo object is recorded (via selrecord()) and then it is
quickly destroyed, with the waiters missing the opportunity to awake,
at the next iteration they will find the selinfo object destroyed,
causing a PF#.
That happens because the selinfo interface has no way to drain the
waiters before to destroy the registered selinfo object. Also this
race is quite rare to get in practice, because it would require a
selrecord(), a poll request by another thread and a quick destruction
of the selrecord()'ed selinfo object.
Fix this by adding the seldrain() routine which should be called
before to destroy the selinfo objects (in order to avoid such case),
and fix the present cases where it might have already been called.
Sometimes, the context is safe enough to prevent this type of race,
like it happens in device drivers which installs selinfo objects on
poll callbacks. There, the destruction of the selinfo object happens
at driver detach time, when all the filedescriptors should be already
closed, thus there cannot be a race.
For this case, mfi(4) device driver can be set as an example, as it
implements a full correct logic for preventing this from happening.
Sponsored by: Sandvine Incorporated
Reported by: rstone
Tested by: pluknet
Reviewed by: jhb, kib
Approved by: re (bz)
MFC after: 3 weeks
environment with a core i5-2500K, operation in this mode causes timeouts
from the mpt driver. Switching to the ACPI-fast timer resolves this issue.
Switching the VM back to single CPU mode also works, which is why I have
not disabled the TSC in that mode.
I did not test with KVM or other VM environments, but I am being cautious
and assuming that the TSC is not reliable in SMP mode there as well.
Reviewed by: kib
Approved by: re (kib)
MFC after: Not applicable, the timecounter code is new for 9.x
resource allocation on x86 platforms:
- Add a new helper API that Host-PCI bridge drivers can use to restrict
resource allocation requests to a set of address ranges for different
resource types.
- For the ACPI Host-PCI bridge driver, use Producer address range resources
in _CRS to enumerate valid address ranges for a given Host-PCI bridge.
This can be disabled by including "hostres" in the debug.acpi.disabled
tunable.
- For the MPTable Host-PCI bridge driver, use entries in the extended
MPTable to determine the valid address ranges for a given Host-PCI
bridge. This required adding code to parse extended table entries.
Similar to the new PCI-PCI bridge driver, these changes are only enabled
if the NEW_PCIB kernel option is enabled (which is enabled by default on
amd64 and i386).
Approved by: re (kib)
processors unless the invariant TSC bit of CPUID is set. Intel processors
may stop incrementing TSC when DPSLP# pin is asserted, according to Intel
processor manuals, i. e., TSC timecounter is useless if the processor can
enter deep sleep state (C3/C4). This problem was accidentally uncovered by
r222869, which increased timecounter quality of P-state invariant TSC, e.g.,
for Core2 Duo T5870 (Family 6, Model f) and Atom N270 (Family 6, Model 1c).
Reported by: Fabian Keil (freebsd-listen at fabiankeil dot de)
Ian FREISLICH (ianf at clue dot co dot za)
Tested by: Fabian Keil (freebsd-listen at fabiankeil dot de)
- Core2 Duo T5870 (C3 state available/enabled)
jkim - Xeon X5150 (C3 state unavailable)
some times compiler inserts redundant instructions to preserve unused upper
32 bits even when it is casted to a 32-bit value. Unfortunately, it seems
the problem becomes more serious when it is shifted, especially on amd64.
- Re-add accidentally removed atomic op. for sysctl(9) handler.
- Remove a period(`.') at the end of a debugging message.
- Consistently spell "low" for "TSC-low" timecounter throughout.
Pointed out by: bde
invariant. For SMP case (TSC-low), it also has to pass SMP synchronization
test and the CPU vendor/model has to be white-listed explicitly. Currently,
all Intel CPUs and single-socket AMD Family 15h processors are listed here.
Discussed with: hackers
TSC timecounter if TSC frequency is higher than ~4.29 MHz (or 2^32-1 Hz) or
multiple CPUs are present. The "TSC-low" frequency is always lower than a
preset maximum value and derived from TSC frequency (by being halved until
it becomes lower than the maximum). Note the maximum value for SMP case is
significantly lower than UP case because we want to reduce (rare but known)
"temporal anomalies" caused by non-serialized RDTSC instruction. Normally,
it is still higher than "ACPI-fast" timecounter frequency (which was default
timecounter hardware for long time until r222222) to be useful.
when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
This fixes heavy interrupt storm and resulting system freeze when using
LAPIC timer in one-shot mode under Xen HVM. There, unlike real hardware,
programming timer with zero period almost immediately causes interrupt.
cpuset_t objects.
That is going to offer the underlying support for a simple bump of
MAXCPU and then support for number of cpus > 32 (as it is today).
Right now, cpumask_t is an int, 32 bits on all our supported architecture.
cpumask_t on the other side is implemented as an array of longs, and
easilly extendible by definition.
The architectures touched by this commit are the following:
- amd64
- i386
- pc98
- arm
- ia64
- XEN
while the others are still missing.
Userland is believed to be fully converted with the changes contained
here.
Some technical notes:
- This commit may be considered an ABI nop for all the architectures
different from amd64 and ia64 (and sparc64 in the future)
- per-cpu members, which are now converted to cpuset_t, needs to be
accessed avoiding migration, because the size of cpuset_t should be
considered unknown
- size of cpuset_t objects is different from kernel and userland (this is
primirally done in order to leave some more space in userland to cope
with KBI extensions). If you need to access kernel cpuset_t from the
userland please refer to example in this patch on how to do that
correctly (kgdb may be a good source, for example).
- Support for other architectures is going to be added soon
- Only MAXCPU for amd64 is bumped now
The patch has been tested by sbruno and Nicholas Esborn on opteron
4 x 12 pack CPUs. More testing on big SMP is expected to came soon.
pluknet tested the patch with his 8-ways on both amd64 and i386.
Tested by: pluknet, sbruno, gianni, Nicholas Esborn
Reviewed by: jeff, jhb, sbruno
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
VMware products virtualize TSC and it run at fixed frequency in so-called
"apparent time". Although virtualized i8254 also runs in apparent time, TSC
calibration always gives slightly off frequency because of the complicated
timer emulation and lost-tick correction mechanism.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
