1) The vnode pager wasn't properly tracking the file size due to
"size" being page rounded in some cases and not in others.
This sometimes resulted in corrupted files. First noticed by
Terry Lambert.
Fixed by changing the "size" pager_alloc parameter to be a 64bit
byte value (as opposed to a 32bit page index) and changing the
pagers and their callers to deal with this properly.
2) Fixed a bogus type cast in round_page() and trunc_page() that
caused some 64bit offsets and sizes to be scrambled. Removing
the cast required adding casts at a few dozen callers.
There may be problems with other bogus casts in close-by
macros. A quick check seemed to indicate that those were okay,
however.
specified. This makes haveseen_isadev() useful for searching for a
free resource. This increases the bitrot in the pci RESOURCE_CHECK
code.
Fixed the pre-attach conflict message. The flag for distinguishing
pre-attach conflict checks from pre-probe ones was never set.
small part of a bug suite beginning in the SLICE probes but mostly in the
floppy driver. This is a quick fix: the auto case shouldn't be special;
DMA should also be stopped in isa_dma_release(); isa_dmastop() probably
shouldn't exist; common DMA registers should not be accessed without
locking.
make isa_dmacascade, isa_dmastart, isa_dmadone, and find_isadev MUCH
easier to be found by starting them at the beginging of the line...
remove braces inside of ifdef RESOURCE_CHECK... found by % in vi...
there is a natural place to initialize `safepri' in a future commit.
Spinoffs:
- spl0() gets called in the unlikely event that isa is not configured.
- configure() has better control over enabling interrupts.
- it is now less unclear that interrupts aren't actually enabled early.
Rev.1.48 of autoconf.c seems to have done the opposite of what was
intended - moving the isa_configure() call delayed the spl0() side
effect.
Added some comments about the bogons. Removed the splhigh() call since
it is a no-op.
these structs for conflics...
it still exist that two PnP cards can colide, but this is up to the user
to make sure it doesn't happen...
other modifications to pnp.c to format output properly, and hide more
output behind bootverbose flag...
fix some bugons in pnp.h that would of made it difficult for inclusion
in external programs (for import of pnpinfo)
and the sound driver which uses auto dma.
The dma interface functionality remains however it now checks
to see if a dma is operating in auto dma mode and if so it bypasses
the busy flag check . I have modified the sound driver 3.5 to
adjust for this new behavior and tested it under FreeBSD 3.0 -current
This patch also includes the new function isa_dmastop.
Submitted by: Amancio Hasty <hasty@rah.star-gate.com>
irqs can't work (at best, the first one attached wins). It used to
be necessary to skip this check because of bogus irqs in the sound
drivers, but the sound drivers have been fixed, except possibly the
OSS ones.
Made NEW_STRATEGY default.
Removed misc. old cruft.
Centralized simple locks into mp_machdep.c
Centralized simple lock macros into param.h
More cleanup in the direction of making splxx()/cpl MP-safe.
Mask the read value from the count register in order to return zero correctly
after TC, as per intel datasheet : "If it is not autoinitialised, this
register will have a count of FFFFH after TC"
comments. Remove reduntant extra addition that was unncessary, and
unneeded mask (asuming inb works correctly).
Submitted by: Stephen McKay <syssgm@dtir.qld.gov.au>
handlers don't skew the results of isa_dmastatus. The function can be
safely called with interrupts disabled.
Submitted by: Stephen McKay <syssgm@dtir.qld.gov.au>
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
- doesn't break my system.
- NOT yet verified on the affected motherboard.
Stifle an annoying dma_start busy message for the sound cards.
Submitted by: "John S. Dyson" <toor@dyson.iquest.net>
Peter Wemm <peter@spinner.DIALix.COM>, Steve Passe <smp@csn.net>
removed all the IPI_INTS code.
made the XFAST_IPI32 code default, renaming Xfastipi32 to Xinvltlb.
cleanup of i386/isa/isa_device.h to eliminate SMP dependancies:
made the id_irq member of struct isa_device an u_int.
made the id_drq member of struct isa_device an int.
removed all other '#ifdefs' concerning SMP & APIC_IO.
removed SMP/APIC_IO dependancies from if_ze.c.
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
print "at <not configured>" for iobase == -1 (autodetect not happens)
and not print anything for iobase == -2 (none)
Old code treat this two special config numbers as big port numbers.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
channel at the same time. The functions isa_dma_acquire() and
isa_dma_release() should be used in all ISA drivers which call isa_dmastart().
This can be used more generally to register the usage of DMA channels in
any driver, but it is required for drivers using isa_dmastart() and friends.
Clean up sanity checks, error messages, etc.
Remove isa_dmadone_nobounce(), it is no longer needed
Reviewed by: bde
