WITHOUT_LOADER_LUA is only needed since we turned it off by default on
powerpc and sparc64 in r338203. Same with
WITHOUT_LOADER_GEIL. WITH_NVME, WITHOUT_NVME, WITH_LOADER_FORCE_LE
have been needed since they were added.
Without this we get spurious output during boot as we try to run
nonexistant HyperV scripts on non-x86 models.
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17211
Since r326030 strings is installed unconditionally so should not be
removed when WITHOUT_TOOLCHAIN is set.
Reported by: Dan McGregor
Approved by: re (kib)
Sponsored by: The FreeBSD Foundation
Make the building of drm dependent on MK_MODULE_DRM and the building
of module drm2 on MK_MODULE_DRM2. The defaults are unchanged.
Approved by: re@ (gjb)
Differential Review: https://reviews.freebsd.org/D16894
vermaden (maintainer of beadm) points out the following inconsistencies:
- "missing command" is not printed prior to usage if the error is simply a
missing command; this should be obvious from the context
- "bectl rename" isn't using the "don't unmount" flag (zfs rename -u), so
the active BE can't be renamed. It doesn't make sense in our context to
*not* use -u, so use it.
Documentation updates reflect the above and note an inconsistency with the
'destroy' command that is consistent with other parts of the base system.
A fix for libbe(3) not properly being installed to /lib is included.
SHLIBDIR should have been added when it was moved in r337995.
Approved by: re (kib)
Checking for any include below ${SRCTOP}/sys is too strict and breaks
e.g. mkimg which includes sys/sys/disk. ABI issues will only be caused
by including headers in sys/sys since they might not match the host.
Approved By: jhb (mentor)
Suggested By: imp
This has two advantages:
1) We no longer create lots of empty directories that are not needed
2) This is a requirement for building on non-FreeBSD hosts since mtree will
only exist after the bootstrap-tools phase there.
Aproved By: jhb (mentor)
Differential Revision: https://reviews.freebsd.org/D16773
This can cause surprising errors if the build tools is built against
headers that don't match the host system. It is also required in order
to allow building on non-FreeBSD systems where the headers in
/usr/include/sys are usually completely incompatible with those in the
source tree.
I added an error to Makefile.boot if this is done and found this was
only the case in libnv. With this error in the Makefile ABI breakages
such as r336019 should no longer be possible.
Reviewed By: bdrewery, kevans
Approved By: jhb (mentor)
Differential Revision: https://reviews.freebsd.org/D16186
BPF (eBPF) is an independent instruction set architecture which is
introduced in Linux a few years ago. Originally, eBPF execute
environment was only inside Linux kernel. However, recent years there
are some user space implementation (https://github.com/iovisor/ubpf,
https://doc.dpdk.org/guides/prog_guide/bpf_lib.html) and kernel space
implementation for FreeBSD is going on
(https://github.com/YutaroHayakawa/generic-ebpf).
The BPF target support can be enabled using WITH_LLVM_TARGET_BPF, as it
is not built by default.
Submitted by: Yutaro Hayakawa <yhayakawa3720@gmail.com>
Reviewed by: dim, bdrewery
Differential Revision: https://reviews.freebsd.org/D16033
Since all post-installkernel steps are assumed to operate in the updated
installation, it's necessary to chroot all of the followup steps in the new
boot environment. Set up and mount the source and object directories at the
same paths inside the BE root, and clean up to the extent changes were made.
This commit fixes upgrading using beinstall past the new ntpd user change.
Improve testability of changes to this script while I'm here.
Reported by: rpokala (earlier patch)
Since r336126 we depend on explicit_bzero() for the libmd
bootstrap. Add it to -legacy if it is not found in /usr/include/strings.h.
Reviewed By: ian
Approved By: brooks (mentor)
Differential Revision: https://reviews.freebsd.org/D16245
Use tools/build/Makefile to install the headers into ${WORLDTMP}/legacy
instead. Compared to r336026 this has the minor advantage that it avoids
unncessary header installation when building the non-bootstrap libnv.
Reviewed By: bdrewery, kevans
Approved By: brooks (mentor)
Differential Revision: https://reviews.freebsd.org/D16187
Add src.conf knob to disable the installation of /var/db/services.db
Default to leaving services.db in place, but allow the removal of the
file and its creation with a src.conf knob.
This file ends up being 2MB in size. For small systems this is a waste
of space but its a tradeoff.
Reviewed by: bdrewery
Differential Revision: https://reviews.freebsd.org/D9655
This will disable the new LLVM_TARGET_ALL option which will only
enable the required target.
This only impacts the bootstrap compiler in WORLDTMP, not the target compiler
that will be installed.
MFC after: 2 weeks
Reviewed by: sbruno, dim (earlier version)
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D16021
LLVM_TARGET_* will auto be set based on LLVM_TARGET_ALL and MK_CLANG.
If LLVM_TARGET_ALL is disabled, during a cross-build, then SYSTEM_COMPILER
and SYSTEM_LINKER are auto disabled.
This option should be used by users rather than the per-arch LLVM_TARGET
options as it is simpler to maintain for them should the supported
target list change.
MFC after: 2 weeks
Reviewed by: sbruno, dim
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D16020
This makes it possible, through src.conf(5) settings, to select which
LLVM targets you want to build during buildworld. The current list is:
* (WITH|WITHOUT)_LLVM_TARGET_AARCH64
* (WITH|WITHOUT)_LLVM_TARGET_ARM
* (WITH|WITHOUT)_LLVM_TARGET_MIPS
* (WITH|WITHOUT)_LLVM_TARGET_POWERPC
* (WITH|WITHOUT)_LLVM_TARGET_SPARC
* (WITH|WITHOUT)_LLVM_TARGET_X86
To not influence anything right now, all of these are on by default, in
situations where clang is enabled.
Selectively turning a few targets off manually should work. Turning on
only one target should work too, even if that target does not correspond
to the build architecture. (In that case, LLVM_NATIVE_ARCH will not be
defined, and you can only use the resulting clang executable for
cross-compiling.)
I performed a few measurements on one of the FreeBSD.org reference
machines, building clang from scratch, with all targets enabled, and
with only the x86 target enabled. The latter was ~12% faster in real
time (on a 32-core box), and ~14% faster in user time. For a full
buildworld the difference will probably be less pronounced, though.
Reviewed by: bdrewery
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D11077
The new stand/ structure installs loader.conf(5) and defaults/loader.conf
regardless of interpreter. The only thing gating installation now is
MK_BOOT.
Reported by: eadler
This works similar to WITH_SYSTEM_COMPILER added in r300354. It only
supports lld via WITH_LLD_BOOTSTRAP.
When both SYSTEM_COMPILER and SYSTEM_LINKER logic passes then libclang
will not build in cross-tools. If either check fails though then
libclang is built.
The .info is reworked to notify when libclang will be built since if
either clang or lld needs to be rebuilt, but not the other, the
notification can lead to confusion on why "clang is building".
-fuse-ld= is not used with this method so some combinations of compiler
and linker are expected to fail.
A new 'make test-system-linker' target is added to see the logic results.
Makefile.inc1:
CROSS_BINUTILS_PREFIX support had to be moved higher up so that XLD
could be set and MK_LLD_BOOTSTRAP disabled before checking SYSTEM_LINKER
logic as done with SYSTEM_COMPILER. This also required moving where
bsd.linker.mk was read since XLD needs to be set before parsing it. This
creates a situation where src.opts.mk can not test LINKER_FEATURES or
add LLD_BOOTSTAP to BROKEN_OPTIONS.
Reviewed by: emaste (earlier version)
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15894
try to build them if MK_OPENSSL is unset.
Reviewed by: emaste imp kevans
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D15211
As of r306649 objcopy is always ELF Tool Chain's elfcopy; binutils
objcopy is never used.
PR: 229046
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
GNU grep as in actually in base does not have any translations support
compiled in, so no functionnality loss.
We do support 193 locales in base, we will never catch up on that number of
translation with bsd grep.
Removing NLS support make bsd grep consistent with the other binaries in base
which are not translated, and also reduce a little bit the code.
Reviewed by: kevans
Approved by: kevans
Discussed with: kevans @BSDCan
Differential Revision: https://reviews.freebsd.org/D15682
It was an old TRE that had plenty of bugs and no performance gain over
regex(3). I disabled it by default in r323615, and there was some confusion
about what the knob does- likely due to poor naming on my part- to the tune
of "well, it sounds like it should speed things up" (mentioned by multiple
people).
To compound this, I have no intention of maintaining a second regex
implementation. If someone would like to step up and volunteer to maintain a
lean-and-mean implementation for grep, this is OK, but we have very few
volunteers to maintain even our primary regex implementation.
Import the wrapper script from zstdgrep (written by wiz@netbsd.org)
Modify it to support more than just zstd (adding support for gzip,
lzma, xz and bzip2)
Write a simple manpage dedicated for it.
Only use that new wrapper both for gnu grep and bsd grep
Next step will be removing code related to compression format from bsdgrep
Reviewed by: kevans
Approved by: kevans
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D15193
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
