common attach function so that the lock gets initialized in all cases.
This fixes breakage of the initialization of the lock in the pci case
in rev.1.135 (between the releases of 5.1 and 5.2). The lock is only
used in the SMP case, so this bug was not always fatal.
vm_mmap_vnode function, where we can safely check for a special /dev/zero
case. Rev. 1.180 has reordered checks and introduced a regression.
Submitted by: alc
Was broken by: kan
and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
It was fixed by moving problemetic checks, as well as checks that
doesn't need locking before locks are acquired.
Submitted by: Ryan Sommers <ryans@gamersimpact.com>
In co-operation with: cperciva, maxim, mlaier, sam
Tested by: submitter (previous patch), me (current patch)
Reviewed by: cperciva, mlaier (previous patch), sam (current patch)
Approved by: sam
Dedicated to: enough!
SCHED_INTERACT_MAX was used where SCHED_SLP_RUN_MAX was needed. This was
causing the interactivity scaler to lose history at a more dramatic rate
than intended.
scenario into #ifdef DEBUG. This makes my cluster with Belkin
KVM switch completely usable, even if the KVM switch and mouse
get a bit confused sometimes.
Without this, when the mouse gets confused, all sorts of crud
gets spammed all over the screen. With this, the mouse may appear
dead for a second or three, but it recovers silently.
phandle_t. Since both are typedefed to unsigned int, this is more
or less cosmetic.
- Fix the code that determines whether a creator instance was used
for firmware output (and should not be blanked on initialization).
Since r1.2 of dev/fb/creator.c, this consisted comparing a handle of
an instance of a package with a handle of the package itself.
Use the test from r1.1, which utilizes OF_instance_to_package().
Submitted by: Marius Strobl <marius@alchemy.franken.de>
+ struct ifnet: remove unused fields, move ipv6-related field close
to each other, add a pointer to l3<->l2 translation tables (arp,nd6,
etc.) for future use.
+ struct route: remove an unused field, move close to each
other some fields that might likely go away in the future
"...If "keyboard" is the selected input-device and "screen" the
output-device (both via /options) but the keyboard is unplugged,
OF automatically switches to ttya for the console, it even prints
a line telling so on "screen". Solaris respects this behaviour and
uses ttya as the console in this case and people probably expect
FreeBSD to do the same (it's also very handy to temporarily switch
consoles)..."
"...I changed the comparison of the console device with "ttya" ||
"ttyb" to "tty" because on AXe boards all 4 onboard UARTs end in
SUB-D connectors (ttya and ttyb being 16550 and ttyc and ttyd a
SAB82532) and there's no Sun keyboard connector (but PS/2). If one
plugs a serial card in a box there also can be more than just ttya
and ttyb available for a console..."
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Has no doubt that the change is correct: marcel
"... uart_cpu_sparc64.c currently only looks at /options if ttyX is
the selected console. However, there's one case where it should
additionally look at /chosen. If "keyboard" is the selected input-
device and "screen" the output-device (both via /options) but the
keyboard is unplugged, OF automatically switches to ttya for the
console. It even prints a line telling so on "screen". Solaris
respects this behaviour and uses ttya as the console in this case
and people probably expect FreeBSD to do the same (it's also very
handy to temporarily switch consoles)..."
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Has no doubt the change is correct: marcel
WARNS=6. I don't change the WARNS level in the Makefile because I
didn't tested this on other archs.
The fs.h fix was suggested by: marcel
Reviewed by: md5(1)
of UARTs. We already did this in uart_cpu_getdev().
While here, also check the compat name for "su" or "su16550".
Both changes submitted by: Marius Strobl <marius@alchemy.franken.de>
Does not doubt the correctness of the second change: marcel
it belongs. Change the implementation to match those of rfs() and
rgs() for consistency and irrespective of whether the original was
more correct or not (technically speaking).
in the process. This is required for proper debugging of corefiles
created by 1:1 or M:N threaded processes. Add an XXX comment where
we should actually call a function that dumps MD specific notes.
An example of a MD specific note is the NT_PRXFPREG note for SSE
registers.
Since BFD creates non-annotated pseudo-sections for the first PRSTATUS
and FPREGSET notes (non-annotated in the sense that the name of the
section does not contain the pid/tid), make sure those sections describe
the initial thread of the process (i.e. the thread which tid equals the
pid). This is not strictly necessary, but makes sure that tools that use
the non-annotated section names will not change behaviour due to this
change.
The practical upshot of this all is that one can see the threads in
the debugger when looking at a corefile. For 1:1 threading this means
that *all* threads are visible.
NFSv3. It's likely that modifying the attributes will affect the
file's accessibility. This version of the patch is one suggested
by Ian Dowse after reviewing my original attempt in the PR
Reviewed By: iedowse
PR: kern/44336
MFC after: 3 days
is twofold:
1. When a 1:1 or M:N threaded process dumps core, we need to put the
register state of each of its kernel threads in the core file.
This can only be done by differentiating the pid field in the
respective note. For this we need the tid.
2. When thread support is present for remote debugging the kernel
with gdb(1), threads need to be identified by an integer due to
limitations in the remote protocol. This requires having a tid.
To minimize the impact of having thread IDs, threads that are created
as part of a fork (i.e. the initial thread in a process) will inherit
the process ID (i.e. tid=pid). Subsequent threads will have IDs larger
than PID_MAX to avoid interference with the pid allocation algorithm.
The assignment of tids is handled by thread_new_tid().
The thread ID allocation algorithm has been written with 3 assumptions
in mind:
1. IDs need to be created as fast a possible,
2. Reuse of IDs may happen instantaneously,
3. Someone else will write a better algorithm.
Add in missing case for i845G in the attach routine. I'll MFC this
with the rest of the change after the 4.10 codefreeze lifts.
Reviewed By: Doug Rabson
Under polling(4), we counted non-existent output packets and wasted
CPU cycles, corrected. (PR kern/64975.)
The fix in revision 1.71 to correct resetting of the watchdog timer
was wrong.
In rl(4), the TX list does not have a gap between the consumer and
producer, so the "empty TX list" test was wrong, corrected.
Also, resetting the timer to five each time we know there is still
some TX work to do was a bad idea -- under polling(4), if the chip
goes out to lunch, this results in the watchdog routine to _never_
be called. Instead, let the timer downgrade to zero and fire the
watchdog, then reset it to five when it is zero AND there is some
TX work left. (Most other network drivers need this fix too.)
MFC after: 3 days
