d_maxio is replaced by the dev->si_iosize_max field which the driver
should be set in all calls to cdevsw->d_open if it has a better
idea than the system wide default.
The field is a generic dev_t field (ie: not disk specific) so that
tapes and other devices can use physio as well.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
be set by a kernel conf option due to the struct buf structural
dependancy (sizing of b_pages[]) creating a conflict with modules
(which are not compiled with kernel config options overrides).
We'll be able to sysctl these two later on when the buffer subsystem
is revamped.
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
`dst_port') work for outgoing packets.
- Make permanent links whose `alias_addr' matches the primary aliasing
address `aliasAddress' work for incoming packets.
- Typo fixes.
Reviewed by: brian, eivind
clustering issues (replacing code that used to be in
ufs/ufs/ufs_readwrite.c). vm_fault also now uses the new VM page counter
inlines.
This completes the changeover from vnode->v_lastr to vm_entry_t->v_lastr
for VM, and fp->f_nextread and fp->f_seqcount (which have been in the
tree for a while). Determination of the I/O strategy (sequential, random,
and so forth) is now handled on a descriptor-by-descriptor basis for
base I/O calls, and on a memory-region-by-memory-region and
process-by-process basis for VM faults.
Reviewed by: David Greenman <dg@root.com>, Alan Cox <alc@cs.rice.edu>
heuristic to detect sequential operation.
VM-related forced clustering code removed from ufs in preparation for a
commit to vm/vm_fault.c that does it more generally.
Reviewed by: David Greenman <dg@root.com>, Alan Cox <alc@cs.rice.edu>
transfer size calculation was incorrect resulting in the last read being
potentially larger then the actual extent of the device.
EOF and write handling has not yet been fixed.
Reviewed by: Tor.Egge@fast.no
the terminating zero by copying MAXCOMLEN + 1 bytes. This fixes the garbage
that occasionally appeared behind the programname when it is at least MAXCOMLEN
bytes long (such as communicator-4.61-bin).
submitter, who *still* hasn't bothered to answer me back.
The thing which the submitter completely failed to mention is that
his 3c900B-TPO card has the transceiver selection in the EEPROM set
to "auto." You can tweak the setting using the 3C90XCFG.EXE utility
that 3Com provides with the card. I'm not sure if it's supposed to
default to auto or if the user fiddled with it. Currently, the xl
driver only does autoselection for 10/100 NICs (i.e. those with NWAY
autonegotiation capabilities). For the 10baseT, 10base5, 10base2,
10baseFL and 100baseFX cards, the driver sets the default media to
whatever the EEPROM transceiver selector says. The problem is that
the "auto" selection is mistakenly identified as "10/100 NWAY
autoselection mode" and this is not handled correctly: the default
media ends up being chosen as 100baseTX, which doesn't work because
we've only added 10baseT media types to the ifmedia word. This leads
to a panic in ifmedia_set() (something else which the submitter never
bothered to mention).
A workaround for this is to re-run the 3C90XCFG.EXE utility and change
the transceiver selection to something besides "auto." I have also
patched the driver to watch for the "auto" setting in the non-miibus
case and select a reasonable default based on the card type instead of
falling through to 100baseTX and exploding.
PR: misc/13665
Rename dev->si_bsize_max to si_iosize_max and set it in spec_open
if the device didn't.
Set vp->v_maxio from dev->si_bsize_max in spec_open rather than
in ufs_bmap.c
spaces which cross a segment boundry in the page table. pmap_kextract()
is not designed for access to the user space portion of the page
table and cannot handle the null-page-directory-entry case.
The fix is to have vm_fault_quick() return a success or failure which
is then used to avoid calling pmap_kextract().
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
improperly ignored the B_INVAL flag when acting on the B_ERROR.
If both B_INVAL and B_ERROR are set the buffer is typically out of the
underlying device's block range and must be destroyed. If only B_ERROR
is set (for a write), a write error occured and operation remains as it
was before: the buffer must be redirtied to avoid corrupting the
filesystem state.
Reviewed by: David Greenman <dg@root.com>
Submitted by: Tor.Egge@fast.no
It is about 2.5 microseconds or roughly 3 times faster to use this
"PIIX" timecounter than the "i8254" timecounter. Resolution is
also 3 times better.
The code cheats and don't register the PCI device, because other pieces
of code want to use it too.
Originally spotted by: msmith
strategy used in the 3Com Linux driver. The new strategy is to use transmit
descriptor polling -- that is, the NIC polls the descriptors to see when
new packets are available for transmission. The advantage to the new scheme
is that no register accesses are needed in the transmit routine. The old
scheme requires several register accesses to stall the TX engine, update the
TX DMA list pointer register, then unstall the TX engine. Hopefully the new
scheme will provide improved transmit performance with less CPU overhead.
This only affects the 3c90xB or 3c90xC cards, not the 3c90x cards. This
means the original 3c900 and 3c905 cards are unaffected. Newer cards include
the 3c900B series, the 3c905B, 3c980, 3c980B, 3c905C and 3c905C, and the
3cSOHO100-TX OfficeConnect.
close PR #13757, however I'm waiting on user feedback before declaring the
PR officially closed. Among other things, this improves UDP transmit
performance, and tx underruns are now detected and the TX start threshold
adjusted accordingly.
far-reaching in fd-land, so you'll want to consult the code for
changes. The biggest change is that now, you don't use
fp->f_ops->fo_foo(fp, bar)
but instead
fo_foo(fp, bar),
which increments and decrements the fp refcount upon entry and exit.
Two new calls, fhold() and fdrop(), are provided. Each does what it
seems like it should, and if fdrop() brings the refcount to zero, the
fd is freed as well.
Thanks to peter ("to hell with it, it looks ok to me.") for his review.
Thanks to msmith for keeping me from putting locks everywhere :)
Reviewed by: peter
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
users have suffered from this breakage, w/o commitment from someone that
they would fix the problems.
This effectively backs out revs 1.{157-160}. It does however fix the
build problem that caused 1.157 to be committed.
If the changes from rev 1.156-1.160 can't be fully tested by the
committer, may I offer posting a diff in the freebsd-current mailing
list for broader testing before inflicting this breakage again.
addaliasu() into addalias() (no operational change) and clarify comments
relating to a trick that vclean() uses.
The fix to BOOTP is yet another hack. Actually, rootfsid handling
is already a major hack. The whole thing needs to be cleaned up.
Reviewed by: David Greenman <dg@root.com>, Alan Cox <alc@cs.rice.edu>
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Make a sonewconn3() which takes an extra argument (proc) so new sockets created
with sonewconn() from a user's system call get the correct credentials, not
just the parent's credentials.
WARNING: libdevstat, iostat, vmstat, systat etc etc will need a recompile.
Add devstat_end_transaction_buf() which pulls all the vital data out
of a struct buf which is ready for biodone().
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
