sc->mii_anegticks according to whether the respective BGE chip
supports Fast Ethernet only or also Gigabit Ethernet.
- At least the BGE chips I've tested with wedge when isolating them
so document this as the reason for setting MIIF_NOISOLATE and
remove the unused (and partially even #ifdef'ed out) isolation
related code. Add code that panics if we encounter a non-zero MII
instance as generally there's no way a PHY requiring MIIF_NOISOLATE
can be handled gracefully in a multi-PHY configuration (it's ok for
the internal PHY of single-PHY-only-NIC to not support isolation
though).
- Additionally set MIIF_NOLOOP as loopback doesn't seem to work
either and remove the #ifdef'ed out code for adding respective
media. The MIIF_NOLOOP flag currently triggers nothing but
hopefully will be respected by mii_phy_setmedia() later on.
Reviewed by: jkim, yongari
MFC after: 1 month
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
- Wake up DMA engine after adding a new receive buffer.
- Skip buffers which have unknown state after error.
- More rigid error detection.
MFC after: 1 week
as some combinations of chipset, controller and target do not behave
correctly when DMA is enabled for other commands.
PR: kern/103602
MFC after: 2 weeks
were never freed, but the big ring was freed twice.
-Don't supply rx hw csums for frames which are padded beyond the
length specified in the ip header. If the padding is non-zero,
the hw csum will be incorrect for such frames.
Sponsored by: Myricom
This workaround the problem in Parallels/VMWare where the emulated drivers are
slower, especially with ATA_FLUSHCACHE. The problem appears much more
frequently with ZFS which use it a lot more.
Approved: sos, pjd
specific request and thus should first try to be allocated from the
sys_resource pool. This avoids using the sys_resource pool for wildcard
requests that have bounded ranges coming from cbb(4) and Host-PCI pcib(4)
drivers.
Tested by: Andrea Bittau <a.bittau of cs.ucl.ac.uk fame>
Sleuthing by: Andrea Bittau as well
that the MSI mapping window is fixed at 0xfee00000 and the capability
does not include two more dwords used to program the address. Supporting
this mostly results in quieting spurious warnings during boot about
non-default MSI mapping windows.
- HT 2.00b also added a new HT capability type, so support that in pciconf.
MFC after: 3 days
Tested by: jmg
It seems that valid pause frames(Tx flow control) cause GMAC to hang
such that it resulted in watchdog timeout. As a work around don't
flush Rx MAC FIFO if we've received pause frames.
Tested by: Harald Schmalzbauer (h DOT schmalzbauer AT omnisec DOT de)
Under certain circumtances, if TSO is active, Yukon II generates
corrupted IP packets. All corrupted IP packets I noticed were the the
last segmented packet in a TSO request. The corrupted packet resulted
in retransmission of the damaged packet which in turn decreased network
performance dramatically.
Unfortunately it seems that there is no way to workaround this bug
as TSO is completely handled in hardware. Disable TSO until we find a
working workaround or a new silicon revision that doesn't have this
hardware bug.
supports software encrypt/decrypt.
The nuked code itself is quite problematic, as pointed out by sam@ ---
wk->wk_keyix should be replaced by the loop count.
Tested with WEP/TKIP/CCMP/no-protection.
Approved by: sam@ (mentor)
Noticed by: Hans Petter Selasky <hselasky@c2i.net>
and new SCBs were allocated on demand later if needed. This has two
problems. First, allocating SCBs involves allocating contiguous memory,
and if memory is exhausted then the VM will try to page out to satisfy
the request, leading to recursion and deadlock. The second problem is
that it can cause lock order reversals due to parts of the VM still being
under Giant.
Fix the problem be allocating the full pool at driver attach, when it is
safe to do so.
and should only be applied on certain specific card / vendor, hence the
addition of ac97_getsubvendor().
- Fix low volume issue on several MSI laptops through ALC655 quirk.
Reported/Tested by: Christian Mueller
<raptor-freebsd-multimedia@xpls.de>
MFC after: 1 week
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
Group mutexes used in hwpmc(4) into 3 "types" in the sense of
witness(4):
- leaf spin mutexes---only one of these should be held at a time,
so these mutexes are specified as belonging to a single witness
type "pmc-leaf".
- `struct pmc_owner' descriptors are protected by a spin mutex of
witness type "pmc-owner-proc". Since we call wakeup_one() while
holding these mutexes, the witness type of these mutexes needs
to dominate that of "sleepq chain" mutexes.
- logger threads use a sleep mutex, of type "pmc-sleep".
Submitted by: wkoszek (earlier patch)
Previously whenever PROMISC mode turned on/off link renegotiation
occurs and it could resulted in network unavailability for serveral
seconds.(Depending on switch STP settings it could last several tens
seconds.)
Reported by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
Tested by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
