useful for accessing more than 1 page of contiguous physical memory, and
to use 4mb tlb entries instead of 8k. This requires that the system only
use the direct mapped addresses when they have the same virtual colour as
all other mappings of the same page, instead of being able to choose the
colour and cachability of the mapping.
- Adapt the physical page copying and zeroing functions to account for not
being able to choose the colour or cachability of the direct mapped
address. This adds a lot more cases to handle. Basically when a page has
a different colour than its direct mapped address we have a choice between
bypassing the data cache and using physical addresses directly, which
requires a cache flush, or mapping it at the right colour, which requires
a tlb flush. For now we choose to map the page and do the tlb flush.
This will allows the direct mapped addresses to be used for more things
that don't require normal pmap handling, including mapping the vm_page
structures, the message buffer, temporary mappings for crash dumps, and will
provide greater benefit for implementing uma_small_alloc, due to the much
greater tlb coverage.
- Added support for ITR (interrupt throttle register). This feature is available on
adapters based on 82545 and above
- Fixed problem with vlan support when traffic has priority bits set. (kern/45907)
PR: kern/45907
MFC after: 1 week
to current leaves because function may vanish the current node.
If parent RTA_GENMASK route has a clone (a "cloning clone"), an
rn_walktree_from() starting from parent will cause another walk
starting from clone. If a function is either rt_fixdelete() or
rt_fixchange(), this recursive walk may vanish the leaf that is
remembered by an outer walk (the "next leaf" above), panicing a
system when it resumes with an outer walk.
The following script paniced my single-user mode booted system:
: sysctl net.inet.ip.forwarding=1
: ipfw add 1 allow ip from any to any
: ifconfig lo0 127.1
: route add -net 10 -genmask 255.255.255.0 127.1
: telnet 10.1 # rt_fixchange() panic
: telnet 10.2
: telnet 10.1
: route delete -net 10 # rt_fixdelete() panic
For the time being, avoid these races by disallowing recursive
walks in rt_fixchange() and rt_fixdelete().
Also, make a slight optimization in the rtrequest(RTM_RESOLVE)
case: there is no reason to call rt_fixchange() in this case.
PR: kern/37606
MFC after: 5 days
I/O port range, then we should ignore a resource if it's NOT
a memory range AND NOT an I/O port range.
The OR in the condition caused us to ignore perfectly valid
memory addresses.
While here, remove redundant parenthesis and reindent the
debug print to avoid long lines.
- Put the kernel tsb before before the kernel load address, below
VM_MIN_KERNEL_ADDRESS, instead of after the kernel where it consumes
usable kva. This is magic mapped so the virtual address is irrelevant,
it just needs to be out of the way.
a mapping belongs to by setting it in the vm_page_t structure that backs
the tsb page that the tte for a mapping is in. This allows the pmap that
a mapping belongs to to be found without keeping a pointer to it in the
tte itself.
- Remove the pmap pointer from struct tte and use the space to make the
tte pv lists doubly linked (TAILQs), like on other architectures. This
makes entering or removing a mapping O(1) instead of O(n) where n is the
number of pmaps a page is mapped by (including kernel_pmap).
- Use atomic ops for setting and clearing bits in the ttes, now that they
return the old value and can be easily used for this purpose.
- Use __builtin_memset for zeroing ttes instead of bzero, so that gcc will
inline it (4 inline stores using %g0 instead of a function call).
- Initially set the virtual colour for all the vm_page_ts to be equal to their
physical colour. This will be more useful once uma_small_alloc is
implemented, but basically pages with virtual colour equal to phsyical
colour are easier to handle at the pmap level because they can be safely
accessed through cachable direct virtual to physical mappings with that
colour, without fear of causing illegal dcache aliases.
In total these changes give a minor performance improvement, about 1%
reduction in system time during buildworld.
identify themselves as serial cards that it would be desirable to
attach a different driver than sio to. Since we are claiming all
serial cards, this is not possible. Instead, return -100 to indicate
that we're willing to take the card, but still allow other drivers to
attach.
Pointed out by: Maksim Yevmenkin
associated with the syncache entry: in case tcp_close() has been
called on the corresponding listening socket, the lock has been
destroyed as a side effect of in_pcbdetach(), causing a panic when
we attempt to lock on it.
Reviewed by: hsu
The duplication is caused by the fact that imgact_elf.c is included
by both imgact_elf32.c and imgact_elf64.c and both are compiled by
default on ia64. Consequently, we have two seperate copies of the
elf_legacy_coredump variable due to them being declared static, and
two entries for the same sysctl in the linker set, both referencing
the unique copy of the elf_legacy_coredump variable. Since the second
sysctl cannot be registered, one of the elf_legacy_coredump variables
can not be tuned (if ordering still holds, it's the ELF64 related one).
The only solution is to create two different sysctl variables, just
like the elf<32|64>_trace sysctl variables. This unfortunately is an
(user) interface change, but unavoidable. Thus, on ELF32 platforms
the sysctl variable is called elf32_legacy_coredump and on ELF64
platforms it is called elf64_legacy_coredump. Platforms that have
both ELF formats have both sysctl variables.
These variables should probably be retired sooner rather than later.
not < the size of the device. This avoids geom complaints.
Fix a serious bug in the handling of the RS_NO_CLEAR_UA quirk. When we
go and insert the test-unit-ready command the umass_cam_quirk_cb() function
sets the status as if the READ_CAPACITY command suceeded when, in fact, it
did not. This leads to the CAM layer trying to use garbage in the return
buffer and panicing the system (or doing other bad things).
Add a quirk entry for MSYSTEMS DISK-ON-KEY, which is sold under the Sony
brand as a solid state disk-on-key usb device. This device requires
several quirks to work properly.
Note that the disk-on-key device will not work properly until CAM also
gets a quirk entry for it, which has been submitted to the CAM maintainer,
and you may have to temporarily uncomment the DELAY() as well. -current
does not properly wait for devices to power up so you may also have
to temporarily uncomment the DELAY(300000) to make your device work.
A solution must be found to that issue.
MFC after: 3 days
X-MFC note: the quirk support must MFCd before this patch can be
