Rather than trying to KASSERT for callers that invoke this on
IO tags, either do nothing (for write_8) or return ~0 (for read_8).
Using KASSERT here just makes bus.h too messy from both
polluting bus.h with systm.h (for any number of drivers that include
bus.h without first including systm.h) or ports that use bus.h
directly (i.e. libpciaccess) as reported by zeising@.
Also don't try to implement all of the other bus_space functions for
8 byte access since realistically only these two are needed for some
devices that expose 64-bit memory-mapped registers.
Put the amd64-specific functions here rather than sys/amd64/include/bus.h
so that we can keep this header unified for x86, as requested by mdf@
and tijl@.
Submitted by: Carl Delsey <carl.r.delsey@intel.com>
MFC after: 3 days
initialisation to be enabled (1) / disabled (0) defaults to enabled.
This is useful for devices which have a slow trim speed and are either
new or have otherwise already been wiped e.g. secure erase.
PR: kern/173116
Submitted by: Steven Hartland
Approved by: pjd (mentor)
making range consolidation much more effective particularly for small
deletes.
This reduces memory used by the free map as well as reducing the number
of bio requests down to geom required to process all deletes.
In tests this achieved a factor of 10 reduction of trim ranges / geom
call downs.
While I'm here correct the description of zio_vdev_io_start.
PR: kern/173254
Submitted by: Steven Hartland
Approved by: pjd (mentor)
date: 2009/03/31 01:21:29; author: dlg; state: Exp; lines: +9 -16
...
this also firms up some of the input parsing so it handles short frames a
bit better.
This actually fixes reading beyond mbuf data area in pfsync_input(), that
may happen at certain pfsync datagrams.
entering llentry_free(), and in case if we lose the race, we should simply
perform LLE_FREE_LOCKED(). Otherwise, if the race is lost by the thread
performing arptimer(), it will remove two references from the lle instead
of one.
Reported by: Ian FREISLICH <ianf clue.co.za>
Prior to r222417, setting `password' in loader.conf(5) did not prevent boot
but instead only prevented changes to boot options by prompting for password
if autoboot failed or the user interrupted the countdown sequence.
After r222417 the same machine with `password' set in loader.conf(5) would no
longer boot without _always_ entering the password.
This patch restores the old (8.x and older) functionality for password in
loader.conf(5) while adding a new bootlock_password feature to replace the
edge-case should anybody desire the regressed functionality (HINT: great for
PXE servers and/or private distributions).
loader.conf(5) was updated to be more clear with-respect to password setting
(previous text was misleading).
Documentation (loader.conf(5) and check-password.4th(8)) has been updated to
include notes on the new bootlock_password setting.
Special thanks to Alex Verbod for bringing this to my attention and helping to
refine the loader.conf(5) text.
PR: conf/170110
Submitted by: Vitaly Zakharov <ded3axap@gmail.com>
Reviewed by: Alexander Verbod <alexander.verbod@gmail.com>
but later after processing and freeing the tag, we need to jump back again
to the findpcb label. Since the fwd_tag pointer wasn't NULL we tried to
process and free the tag for second time.
Reported & tested by: Pawel Tyll <ptyll nitronet.pl>
MFC after: 3 days
I am not exactly sure about the naming due to lack of specs on AMD site,
but it is better to have some identification then none at all.
MFC after: 1 month
guest floating point state without having to know the
size of floating-point state.
Unstaticize fpurestore to allow the hypervisor to
save/restore guest state using fpusave/fpurestore
on the allocated FPU state area.
Reviewed by: kib
Obtained from: NetApp/bhyve
MFC after: 1 week
These must have been accidently copied from the if statement a few
lines later. Also remove parameter name from function prototype.
Approved by: grehan (mentor)
as r242694):
do better detection of when we have a better version of the tcp sequence
windows than our peer.
this resolves the last of the pfsync traffic storm issues ive been able to
produce, and therefore makes it possible to do usable active-active
statuful firewalls with pf.
This is an ongoing effort to provide runtime debug information
useful in the field that does not panic existing installations.
This gives us the flexibility needed when shipping images to a
potentially large audience with WITNESS enabled without worrying
about formerly non-fatal LORs hurting a release.
Sponsored by: iXsystems
In preparation for sysctl(8) growing the ability to only print
out boot/run-time tunables we need a way to differentiate between
RW sysctl nodes that tune a particular thing, or simply export
a stat that we want to allow the sysadmin to reset to 0 (or some
other value).
To do so, we add the CTLFLAG_STATS which should be OR'd into the
CTLFLAGs when exporting a "writable/resettable" statistic node via
sysctl.
kern_yield() is problematic than.
The owned mutex is the mount interlock, and it is in fact not needed
to guarantee the stability of the mount list of active vnodes, so fix
the the issue by only taking the mount interlock for MNT_REF and
MNT_REL operations.
While there, augment the unconditional yield by some amount of
spinning [1].
Reported and tested by: pho
Reviewed by: attilio
Submitted by: attilio [1]
MFC after: 3 days
cause kernel panics.
Add a flag to the bpf descriptor to indicate whether the hold buffer
is in use. In bpfread(), set the "hold buffer in use" flag before
dropping the descriptor lock during the call to bpf_uiomove().
Everywhere else the hold buffer is used or changed, wait while
the hold buffer is in use by bpfread(). Add a KASSERT in bpfread()
after re-acquiring the descriptor lock to assist uncovering any
additional hold buffer races.
an IBSS VAP to RUN.
An 11n IBSS was beaconing HTINFO/HTCAP IE's that didn't have any HT
information setup (like the HT TX/RX MCS bitmask.)
Tested:
* AR9280, IBSS - both a statically setup channel and a scanned channel
PR: kern/172955
hierarchy of the page table entries which map the specified address.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
call. The function indicates a failure by the TRUE return value. To
be extra safe, assert that the return value from the following
vm_map_insert() indicates success.
Fix style issues in the nearby lines, reformulate the comment.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
parameters in IBSSes.
IBSS was just being plainly ignored here even though aggressive mode
was 'on'.
This still doesn't fix the "why are the WME parameters reset upon
interface down/up" issue.
PR: kern/165969
is totally wrong.
If we parse the WME IE here, we'll be constantly updating the WME
configuration from each WME enabled IBSS node we see.
There's a separate issue where the WME configuration is blanked out
when the interface is brought up; the WME parameters aren't "sticky."
Also, ieee80211_init_neighbor() parses the ath IE, so doing it here
isn't required.
Sorry about the noise.
PR: kern/165969
The Adhoc support wasn't parsing and handling the ath specific and WME
IEs, thus the atheros vendor support and WME TXOP parameters aren't being
copied from the peer.
It copies the WME parameters from whichever adhoc node it decides to
associate to, rather than just having them be statically configured
per adhoc node. This may or may not be exactly "right", but it's certainly
going to be more convienent for people - they just have to ensure their
adhoc nodes are setup with correct WME parameters.
Since WME parameters aren't per-node but are configured on hardware TX
queues, if some nodes support WME and some don't - or perhaps, have
different WME parameters - things will get quite quirky.
So ensure that you configure your adhoc nodes with the same WME
parameters.
Secondly - the Atheros Vendor IE is parsed and operated on per-node, so
this should work out ok between nodes that do and don't do Atheros
extensions. Once you see a becaon from that node and you setup the
association state, it _should_ parse things correctly.
TODO:
* I do need to ensure that both adhoc setup paths are correctly updating
the IE stuff. Ie, if the adhoc node is created by a data frame instead
of a beacon frame, it'll come up with no WME/ath IE config. The next
beacon frame that it receives from that node will update the state.
I just need to sit down and better understand how that's suppose to
work in IBSS mode.
Tested:
* AR5416 <-> AR9280 - fast frames and the WME configuration both popped
up. (This is with a local HAL patch that enables the fast frames
capability on the AR5416 chipsets.)
PR: kern/165969
ctl_frontend_cam_sim.c: Coalesce cfcs_online() and cfcs_offline()
into a single function since these were
identical except for one line.
Make sure we hold the SIM lock around path
creation, and calling xpt_rescan().
scsi_ctl.c: In ctlfe_onoffline(), make sure we hold the
SIM lock around path creation and free
calls, as well as xpt_action().
In ctlfe_lun_enable(), hold the SIM lock
around path and peripheral operations that
require it.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
The stageqdepth (global, over all staging queues) was being kept
incorrectly. It was being incremented whenever things were added,
but only decremented during a flush. During active fast frames activity
it wasn't being decremented, resulting in it always having a non-zero
value during normal fast-frames operation.
It was only used when checking if the aging queue should be checked;
we may as well just defer to each of those staging queue counters (which
look correct, thankfully.)
Whilst I'm here, add locking assertions in the staging queue add/remove
functions. The current crash shows that the staging queue has one frame,
but only has a tail pointer set (the head pointer being set to NULL.)
I'd like to grab a few more crashes where these locking assertions are
in place so I can narrow down the issue between "somehow locking is
messed up and things are racy" and "the stage queue head/tail pointer
manipulation logic is subtly wrong."
Tested:
* AR5416 STA, AR5413 AP; with FastFrames enabled in the AR5416 HAL.
PR: kern/174283
Committed with changes to support the following from loader.conf(5):
+ console="vidconsole comconsole" (not just console="comconsole")
+ boot_serial="anything" (not just boot_serial="YES")
+ boot_multicons="anything" (unsupported in originally-submitted patch)
PR: conf/121064
Submitted by: koitsu
Reviewed by: gcooper, adrian (co-mentor)
Approved by: adrian (co-mentor)
pointers and leave the stage queue flush routine to just do nothing
(since both head and tail here will be NULL.)
This should quieten the "stageq empty" panic where the stageq itself
is empty, but it won't fix the second KASSERT() here "staging queue empty"
as that's likely a different underlying problem.
PR: kern/174283
similar changes had to be made in various places throughout the machine-
independent virtual memory layer to support the new vm object type.
However, in most of these places, it's actually not the type of the vm
object that matters to us but instead certain attributes of its pages.
For example, OBJT_DEVICE, OBJT_MGTDEVICE, and OBJT_SG objects contain
fictitious pages. In other words, in most of these places, we were
testing the vm object's type to determine if it contained fictitious (or
unmanaged) pages.
To both simplify the code in these places and make the addition of future
vm object types easier, this change introduces two new vm object flags
that describe attributes of the vm object's pages, specifically, whether
they are fictitious or unmanaged.
Reviewed and tested by: kib
to head. I don't think the NFS client behaviour will change unless
the new "minorversion=1" mount option is used. It includes basic
NFSv4.1 support plus support for pNFS using the Files Layout only.
All problems detecting during an NFSv4.1 Bakeathon testing event
in June 2012 have been resolved in this code and it has been tested
against the NFSv4.1 server available to me.
Although not reviewed, I believe that kib@ has looked at it.
