(at least a new one) would expect the manual page to be called (even
if the device is lo#).
PR: 32453
Submitted by: Gary W. Swearingen <swear@blarg.net>
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
cd src/share; find man[1-9] -type f|xargs perl -pi -e 's/[ \t]+$//'
BTW, what editors are the culprits? I'm using vim and it shows
me whitespace at EOL in troff files with a thick blue block...
Reviewed by: Silence from cvs diff -b
MFC after: 7 days
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.