state change and reliable error recovery.
o Moved vr_softc structure and relevant macros to header file.
o Use PCIR_BAR macro to get BARs.
o Implemented suspend/resume methods.
o Implemented automatic Tx threshold configuration which will be
activated when it suffers from Tx underrun. Also Tx underrun
will try to restart only Tx path and resort to previous
full-reset(both Rx/Tx) operation if restarting Tx path have failed.
o Removed old bit-banging MII interface. Rhine provides simple and
efficient MII interface. While I'm here show PHY address and PHY
register number when its read/write operation was failed.
o Define VR_MII_TIMEOUT constant and use it in MII access routines.
o Always honor link up/down state reported by mii layers. The link
state information is used in vr_start() to determine whether we
got a valid link.
o Removed vr_setcfg() which is now handled in vr_link_task(), link
state taskqueue handler. When mii layer reports link state changes
the taskqueue handler reprograms MAC to reflect negotiated duplex
settings. Flow-control changes are not handled yet and it should
be revisited when mii layer knows the notion of flow-control.
o Added a new sysctl interface to get statistics of an instance of
the driver.(sysctl dev.vr.0.stats=1)
o Chip name was renamed to reflect the official name of the chips
described in VIA Rhine I/II/III datasheet.
REV_ID_3065_A -> REV_ID_VT6102_A
REV_ID_3065_B -> REV_ID_VT6102_B
REV_ID_3065_C -> REV_ID_VT6102_C
REV_ID_3106_J -> REV_ID_VT6105_A0
REV_ID_3106_S -> REV_ID_VT6105M_A0
The following chip revisions were added.
#define REV_ID_VT6105_B0 0x83
#define REV_ID_VT6105_LOM 0x8A
#define REV_ID_VT6107_A0 0x8C
#define REV_ID_VT6107_A1 0x8D
#define REV_ID_VT6105M_B1 0x94
o Always show chip revision number in device attach. This shall help
identifying revision specific issues.
o Check whether EEPROM reloading is complete by inspecting the state
of VR_EECSR_LOAD bit. This bit is self-cleared after the EEPROM
reloading. Previously vr(4) blindly spins for 200us which may/may
not enough to complete the EEPROM reload.
o Removed if_mtu setup. It's done in ether_ifattach().
o Use our own callout to drive watchdog timer.
o In vr_attach disable further interrupts after reset. For VT6102 or
newer hardwares, diable MII state change interrupt as well because
mii state handling is done by mii layer.
o Add more sane register initialization for VT6102 or newer chips.
- Have NIC report error instead of retrying forever.
- Let hardware detect MII coding error.
- Enable MODE10T mode.
- Enable memory-read-multiple for VT6107.
o PHY address for VT6105 or newer chips is located at fixed address 1.
For older chips the PHY address is stored in VR_PHYADDR register.
Armed with these information, there is no need to re-read
VR_PHYADDR register in miibus handler to get PHY address. This
saves one register access cycle for each MII access.
o Don't reprogram VR_PHYADDR register whenever access to a register
located at a PHY address is made. Rhine fmaily allows reprogramming
PHY address location via VR_PHYADDR register depending on
VR_MIISTAT_PHYOPT bit of VR_MIISTAT register. This used to lead
numerous phantom PHYs attached to miibus during phy probe phase and
driver used to limit allowable PHY address in mii register accessors
for certain chip revisions. This removes one more register access
cycle for each MII access.
o Correctly set VLAN header length.
o bus_dma(9) conversion.
- Limit DMA access to be in range of 32bit address space. Hardware
doesn't support DAC.
- Apply descriptor ring alignment requirements(16 bytes alignment)
- Apply Rx buffer address alignment requirements(4 bytes alignment)
- Apply Tx buffer address alignment requirements(4 bytes alignment)
for Rhine I chip. Rhine II or III has no Tx buffer address
alignment restrictions, though.
- Reduce number of allowable number of DMA segments to 8.
- Removed the atomic(9) used in descriptor ownership managements
as it's job of bus_dmamap_sync(9).
With these change vr(4) should work on all platforms.
o Rhine uses two separated 8bits command registers to control Tx/Rx
MAC. So don't access it as a single 16bit register.
o For non-strict alignment architectures vr(4) no longer require
time-consuming copy operation for received frames to align IP
header. This greatly improves Rx performance on i386/amd64
platforms. However the alignment is still necessary for
strict-alignment platforms(e.g. sparc64). The alignment is handled
in new fuction vr_fixup_rx().
o vr_rxeof() now rejects multiple-segmented(fragmented) frames as
vr(4) is not ready to handle this situation. Datasheet said nothing
about the reason when/why it happens.
o In vr_newbuf() don't set VR_RXSTAT_FIRSTFRAG/VR_RXSTAT_LASTFRAG
bits as it's set by hardware.
o Don't pass checksum offload information to upper layer for
fragmented frames. The hardware assisted checksum is valid only
when the frame is non-fragmented IP frames. Also mark the checksum
is valid for corrupted frames such that upper layers doesn't need
to recompute the checksum with software routine.
o Removed vr_rxeoc(). RxDMA doesn't seem to need to be idle before
sending VR_CMD_RX_GO command. Previously it used to stop RxDMA
first which in turn resulted in long delays in Rx error recovery.
o Rewrote Tx completion handler.
- Always check VR_TXSTAT_OWN bit in status word prior to
inspecting other status bits in the status word.
- Collision counter updates were corrected as VT3071 or newer
ones use different bits to notify collisions.
- Unlike other chip revisions, VT86C100A uses different bit to
indicate Tx underrun. For VT3071 or newer ones, check both
VR_TXSTAT_TBUFF and VR_TXSTAT_UDF bits to see whether Tx
underrun was happend. In case of Tx underrun requeue the failed
frame and restart stalled Tx SM. Also double Tx DMA threshold
size on each failure to mitigate future Tx underruns.
- Disarm watchdog timer only if we have no queued packets,
otherwise don't touch watchdog timer.
o Rewrote interrupt handler.
- status word in Tx/Rx descriptors indicates more detailed error
state required to recover from the specific error. There is no
need to rely on interrupt status word to recover from Tx/Rx
error except PCI bus error. Other event notifications like
statistics counter overflows or link state events will be
handled in main interrupt handler.
- Don't touch VR_IMR register if we are in suspend mode. Touching
the register may hang the hardware if we are in suspended state.
Previously it seems that touching VR_IMR register in interrupt
handler was to work-around panic occurred in system shutdown
stage on SMP systems. I think that work-around would hide
root-cause of the panic and I couldn't reproduce the panic
with multiple attempts on my box.
o While padding space to meet minimum frame size, zero the pad data
in order to avoid possibly leaking sensitive data.
o Rewrote vr_start_locked().
- Don't try to queue packets if number of available Tx descriptors
are short than that of required one.
o Don't reinitialize hardware whenever media configuration is
changed. Media/link state changes are reported from mii layer if
this happens and vr_link_task() will perform necessary changes.
o Don't reinitialize hardware if only PROMISC bit was changed. Just
toggle the PROMISC bit in hardware is sufficient to reflect the
request.
o Rearrganed the IFCAP_POLLING/IFCAP_HWCSUM handling in vr_ioctl().
o Generate Tx completion interrupts for every VR_TX_INTR_THRESH-th
frames. This reduces Tx completion interrupts under heavy network
loads.
o Since vr(4) doesn't request Tx interrupts for every queued frames,
reclaim any pending descriptors not handled in Tx completion
handler before actually firing up watchdog timeouts.
o Added vr_tx_stop()/vr_rx_stop() to wait for the end of active
TxDMA/RxDMA cycles(draining). These routines are used in vr_stop()
to ensure sane state of MAC before releasing allocated Tx/Rx
buffers. vr_link_task() also takes advantage of these functions to
get to idle state prior to restarting Tx/Rx.
o Added vr_tx_start()/vr_rx_start() to restart Rx/Tx. By separating
Rx operation from Tx operation vr(4) no longer need to full-reset
the hardware in case of Tx/Rx error recovery.
o Implemented WOL.
o Added VT6105M specific register definitions. VT6105M has the
following hardware capabilities.
- Tx/Rx IP/TCP/UDP checksum offload.
- VLAN hardware tag insertion/extraction. Due to lack of information
for getting extracted VLAN tag in Rx path, VLAN hardware support
was not implemented yet.
- CAM(Content Addressable Memory) based 32 entry perfect multicast/
VLAN filtering.
- 8 priority queues.
o Implemented CAM based 32 entry perfect multicast filtering for
VT6105M. If number of multicast entry is greater than 32, vr(4)
uses traditional hash based filtering.
o Reflect real Tx/Rx descriptor structure. Previously vr(4) used to
embed other driver (private) data into these structure. This type
of embedding make it hard to work on LP64 systems.
o Removed unused vr_mii_frame structure and MII bit-baning
definitions.
o Added new PCI configuration registers that controls mii operation
and mode selection.
o Reduced number of Tx/Rx descriptors to 128 from 256. From my
testing, increasing number of descriptors above than 64 didn't help
increasing performance at all. Experimentations show 128 Rx
descriptors seems to help a lot reducing Rx FIFO overruns under
high system loads. It seems the poor Tx performance of Rhine
hardwares comes from the limitation of hardware. You wouldn't
satuarte the link with vr(4) no matter how fast CPU/large number of
descriptors are used.
o Added vr_statistics structure to hold various counter values.
No regression was reported but one variant of Rhine III(VT6105M)
found on RouterBOARD 44 does not work yet(Reported by Milan Obuch).
I hope this would be resolved in near future.
I'd like to say big thanks to Mike Tancsa who kindly donated a Rhine
hardware to me. Without his enthusiastic testing and feedbacks
overhauling vr(4) never have been possible. Also thanks to Masayuki
Murayama who provided some good comments on the hardware's internals.
This driver is result of combined effort of many users who provided
many feedbacks so I'd like to say special thanks to them.
Hardware donated by: Mike Tancsa (mike AT sentex dot net)
Reviewed by: remko (initial version)
Tested by: Mike Tancsa(x86), JoaoBR ( joao AT matik DOT com DOT br )
Marcin Wisnicki ( mwisnicki+freebsd AT gmail DOT com )
Stefan Ehmann ( shoesoft AT gmx DOT net )
Florian Smeets ( flo AT kasimir DOT com )
Phil Oleson ( oz AT nixil DOT net )
Larry Baird ( lab AT gta DOT com )
Milan Obuch ( freebsd-current AT dino DOT sk )
remko (initial version)
the cpufreq drivers to reliably use properties of PCI devices for quirks,
etc.
- For the legacy drivers, add CPU devices via an identify routine in the
CPU driver itself rather than in the legacy driver's attach routine.
- Add CPU devices after Host-PCI bridges in the acpi bus driver.
- Change the ichss(4) driver to use pci_find_bsf() to locate the ICH and
check its device ID rather than having a bogus PCI attachment that only
checked for the ID in probe and always failed. As a side effect, you
can now kldload ichss after boot.
- Fix the ichss(4) driver to use the correct device_t for the ICH (and not
for ichss0) when doing PCI config space operations to enable SpeedStep.
MFC after: 2 weeks
Reviewed by: njl, Andriy Gapon avg of icyb.net.ua
the appropriate bit in the DEVACTB register.
This change allows the C2 state on those systems to work as expected.
Reviewed by: njl
Submitted by: Andriy Gapon <avg at icyb.net.ua>
MFC after: 1 week
HPT drivers would sometimes test the value of a preprocessor definition but
not always make sure that the definition existed in the first place, leading
to warnings on newer compilers. I blindly assumed the same with this driver,
and it turned out to be wrong and to enable some code that doesn't work.
to flush the TLB instead of hardcoding a size of 33 pages. Apertures of
32MB and 64MB only use a 16 page GATT and an aperture of 128MB only uses
a 32 page GATT, so without this the code could walk off the end of the
pointer and cause a page fault if the next page was unmapped. Also, for
aperture sizes > 128MB, not all of the pages would be read. The Linux
driver has the same bug.
MFC after: 1 week
Tested by: Frédéric PRACA frederic.praca of freebsd-fr.org
TCP/UDP checksum in driver for short frames. For frames that requires
hardware VLAN tag insertion, the checksum offload trick does not
work due to changes of checksum offset in mbuf after the VLAN tag.
Disable hardware checksum offload for VLAN interface to fix the bug.
Reported by: Christopher Cowart < ccowart AT rescomp DOT berkeley DOT edu >
Tested by: Christopher Cowart < ccowart AT rescomp DOT berkeley DOT edu >
MFC after: 5 days
allocator for jumbo frame. Also remove unneeded jlist lock which
is no longer required to protect jumbo buffers.
With these changes jumbo frame performance of nfe(4) was slightly
increased and users should not encounter jumbo buffer allocation
failure anymore.
Patch in the PR was modified to check active jumbo buffers in use
and other possible jumbo buffer leak.
Jumbo buffer usage in lge(4) still wouldn't be reliable due to lack
of driver lock in local jumbo buffer allocator. Either introduce
a new lock to protect jumbo buffer or switch to UMA backed page
allocator for jumbo frame is required.
PR: kern/78072
TSEC is the MAC engine offering 10, 100 or 1000 Mbps speed and is found on
different Freescale parts (MPC83xx, MPC85xx). Depending on the silicon version
there are up to four TSEC units integrated on the chip.
This driver also works with the enhanced version of the controller (eTSEC),
which is backwards compatible, but doesn't take advantage of its additional
features (various off-loading mechanisms) at the moment.
Approved by: cognet (mentor)
Obtained from: Semihalf
MFp4: e500
The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel resources, which are in
turn muxed/demuxed by the Serial Communications Controller (SCC).
Along with core QUICC/SCC functionality a uart(4)-compliant device driver is
provided which allows for serial ports over QUICC/SCC.
Approved by: cognet (mentor)
Obtained from: Juniper
MFp4: e500
The PQ3 is a high performance integrated communications processing system
based on the e500 core, which is an embedded RISC processor that implements
the 32-bit Book E definition of the PowerPC architecture. For details refer
to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPC8555E
This port was tested and successfully run on the following members of the PQ3
family: MPC8533, MPC8541, MPC8548, MPC8555.
The following major integrated peripherals are supported:
* On-chip peripherals bus
* OpenPIC interrupt controller
* UART
* Ethernet (TSEC)
* Host/PCI bridge
* QUICC engine (SCC functionality)
This commit brings the main functionality and will be followed by individual
drivers that are logically separate from this base.
Approved by: cognet (mentor)
Obtained from: Juniper, Semihalf
MFp4: e500
than rely on the lockmgr support [1]:
* bump the waiters only if the interlock is held
* let brelvp() return the waiters count
* rely on brelvp() instead than BUF_LOCKWAITERS() in order to check
for the waiters number
- Remove a namespace pollution introduced recently with lockmgr.h
including lock.h by including lock.h directly in the consumers and
making it mandatory for using lockmgr.
- Modify flags accepted by lockinit():
* introduce LK_NOPROFILE which disables lock profiling for the
specified lockmgr
* introduce LK_QUIET which disables ktr tracing for the specified
lockmgr [2]
* disallow LK_SLEEPFAIL and LK_NOWAIT to be passed there so that it
can only be used on a per-instance basis
- Remove BUF_LOCKWAITERS() and lockwaiters() as they are no longer
used
This patch breaks KPI so __FreBSD_version will be bumped and manpages
updated by further commits. Additively, 'struct buf' changes results in
a disturbed ABI also.
[2] Really, currently there is no ktr tracing in the lockmgr, but it
will be added soon.
[1] Submitted by: kib
Tested by: pho, Andrea Barberio <insomniac at slackware dot it>
just em, there is an igb driver (this follows behavior with our Linux drivers).
All adapters up to the 82575 are supported in em, and new client/desktop support
will continue to be in that adapter.
The igb driver is for new server NICs like the 82575 and its followons.
Advanced features for virtualization and performance will be in this driver.
Also, both drivers now have shared code that is up to the latest we have
released. Some stylistic changes as well.
Enjoy :)
frames. This bug seems to happen on certain hardware model/revision
(e.g. 88E8053) but it's not identified which hardwares are affected.
Revision 1.4 of if_mskreg.h was not enough to workaround the bug.
To workaround it, inrease GMAC FIFO threshold by one FIFO word to
flush received pause frames.
Reported by: das, Kirill Nuzhdin < kirill.nuzhdin AT rad dot chem dot msu dot ru >
Tested by: das, Kirill Nuzhdin
This fixes the panic which happens when mdcreate_vnode() calls vn_close()
and mddestroy() calls it again further down the error handling path.
Reviewed by: kris, kib
MFC after: 3 days
first before they can be set to Explorer mode.
PR: kern/118578
Submitted by: Andriy Gapon <avg@icyb.net.ua> (I added some comments)
Reviewed by: philip
MFC after: 1 month
