auto polling such that it made all controllers obtain link status
information from the state of the LNKRDY input signal. Broadcom
recommends disabling auto polling such that driver should rely on
PHY interrupts for link status change indications. Unfortunately it
seems some controllers(BCM5703, BCM5704 and BCM5705) have PHY
related issues so Linux took other approach to workaround it.
bge(4) didn't follow that and it used to enable auto polling to
workaround it. Restore this old behavior for BCM5700 family
controllers and BCM5705 to use auto polling. For BCM5700 and
BCM5701, it seems it does not need to enable auto polling but I
restored it for safety.
Special thanks to marius who tried lots of patches with patience.
Reported by: marius
Tested by: marius
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add development feature about limiting the
maximum datagram count in each NCM payload.
- zero-pad alignment data
- add TX-interval tuning sysctl
Approved by: thompsa (mentor)
Link UP state could be reported first before actual completion of
auto-negotiation. This change makes bge(4) reprogram BGE_MAC_MODE,
BGE_TX_MODE and BGE_RX_MODE register only after controller got a
valid link.
Previously rl(4) continuously checked whether there are RX events
or TX completions in forever loop. This caused TX starvation under
high RX load as well as consuming too much CPU cycles in the
interrupt handler. If interrupt was shared with other devices which
may be always true due to USB devices in these days, rl(4) also
tried to process the interrupt. This means polling(4) was the only
way to mitigate the these issues.
To address these issues, rl(4) now disables interrupts when it
knows the interrupt is ours and limit the number of iteration of
the loop to 16. The interrupt would be enabled again before exiting
interrupt handler if the driver is still running. Because RX buffer
is 64KB in size, the number of iterations in the loop has nothing
to do with number of RX packets being processed. This change
ensures sending TX frames under high RX load.
RX handler drops a driver lock to pass received frames to upper
stack such that there is a window that user can down the interface.
So rl(4) now checks whether driver is still running before serving
RX or TX completion in the loop.
While I'm here, exit interrupt handler when driver initialized
controller.
With this change, now rl(4) can send frames under high RX load even
though the TX performance is still not good(rl(4) controllers can't
queue more than 4 frames at a time so low TX performance was one of
design issue of rl(4) controllers). It's much better than previous
TX starvation and you should not notice RX performance drop with
this change. Controller still shows poor performance under high
network load but for many cases it's now usable without resorting
to polling(4).
MFC after: 2 weeks
using miibus, since for some devices that use multiple addresses on the bus,
going through miibus may be unclear, and for devices that are not standard
MII PHYs, miibus may throw a fit, necessitating complicated interfaces to
fake the interface that it expects during probe/attach.
o) Make the mv88e61xx SMI interface in octe attach a PHY directly and fix some
mistakes in the code that resulted from trying too hard to present a nice
interface to miibus.
o) Add a PHY driver for the mv88e61xx. If attached (it is optional in kernel
compiles so the default behavior of having a dumb switch is preserved) it
will place the switch in a VLAN-tagging mode such that each physical port
has a VLAN associated with it and interfaces for the VLANs can be created to
address or bridge between them.
XXX It would be nice for this to be part of a single module including the
SMI interface, and for it to fit into a generic switch configuration
framework and for it to use DSA rather than VLANs, but this is a start
and gives some sense of the parameters of such frameworks that are not
currently present in FreeBSD. In lieu of a switch configuration
interface, per-port media status and VLAN settings are in a sysctl tree.
XXX There may be some minor nits remaining in the handling of broadcast,
multicast and unknown destination traffic. It would also be nice to go
through and replace the few remaining magic numbers with macros at some
point in the future.
XXX This has only been tested with the MV88E6161, but it should work with
minimal or no modification on related switches, so support for probing
them was included.
Thanks to Pat Saavedra of TELoIP and Rafal Jaworowski of Semihalf for their
assistance in understanding the switch chipset.
data size greater than 8192. Since soreserve(so, 256*1024, 256*1024)
would always fail for the default value of sb_max, modify clnt_dg.c
so that it uses the calculated values and checks for an error return
from soreserve(). Also, add a check for error return from soreserve()
to clnt_vc.c and change __rpc_get_t_size() to use sb_max_adj instead of
the bogus maxsize == 256*1024.
PR: kern/150910
Reviewed by: jhb
MFC after: 2 weeks
receive producer ring only for BCM5700. It was believed that
BCM5700 with external SSRAM is the only controller that supports
mini ring but it seems all BCM570[0-4] requires to disable mini
receive producer ring. Otherwise, it caused unexpected RX DMA
error or watchdog timeouts.
Reported by: marius, Steve Kargl <sgk <> troutmask dot apl dot washington dot edu>
Tested by: marius, Steve Kargl <sgk <> troutmask dot apl dot washington dot edu>
Short description of the changes:
- attempt to retry some commands for which it is possible (read, query)
- always make a short sleep before checking EC status in polled mode
- periodically poll EC status in interrupt mode
- change logic for detecting broken interrupt delivery and falling back
to polled mode
- check that EC is ready for input before starting a new command, wait
if necessary
This commit is based on the original patch by David Naylor.
PR: kern/150517
Submitted by: David Naylor <naylor.b.david@gmail.com>
Reviewed by: jkim
MFC after: 3 weeks
This is based on the same approach as used in panic().
In theory parallel execution of generic_stop_cpus() could lead to two CPUs
stopping each other and everyone else, and thus a total system halt.
Also, in theory, we should have some smarter locking here, because two
(or more CPUs) could be stopping unrelated sets of CPUs.
But in practice, it seems, this function is only used to stop
"all other" CPUs.
Additionally, I took this opportunity to make amd64-specific suspend_cpus()
function use generic_stop_cpus() instead of rolling out essentially
duplicate code.
This code is based on code by Sandvine Incorporated.
Suggested by: mdf
Reviewed by: jhb, jkim (earlier version)
MFC after: 2 weeks
Since r212650 and before this change sendfile(2) could produce
a partially valid page for a trailing portion of a ZFS vnode.
vm_fault() always wants to see a fully valid page even if it's the last
page that partially extends beyond vnode's end. Otherwise it calls
vop_getpages() to bring in the page. In the case of ZFS this means
that the data is read from the page into the same page and this breaks
checks in ZFS mappedread() - a thread that set VPO_BUSY on the page in
vm_fault() will get blocked forever waiting for it to be cleared.
Many thanks to Kai and Jeremy for reproducing the issue and providing
important debugging information and help.
Reported by: Kai Gallasch <gallasch@free.de>,
Jeremy Chadwick <freebsd@jdc.parodius.com>
Tested by: Kai Gallasch <gallasch@free.de>,
Jeremy Chadwick <freebsd@jdc.parodius.com>
Reviewed by: kib
MFC after: 3 days
To-Do: apply the same treatment to tmpfs + sendfile
kernel of exactly the same __FreeBSD_version as the headers module was
compiled against.
Mark our in-tree ABI emulators with DECLARE_MODULE_TIED. The modules
use kernel interfaces that the Release Engineering Team feel are not
stable enough to guarantee they will not change during the life cycle
of a STABLE branch. In particular, the layout of struct sysentvec is
declared to be not part of the STABLE KBI.
Discussed with: bz, rwatson
Approved by: re (bz, kensmith)
MFC after: 2 weeks
