o create a separate tag for each object allocated with bus_dmamem_alloc so
the tag's maxsize is setup appropriately; this reduces memory allocation
for the queue descriptors from 16M to what it should be and also fixes
memory allocation for public key operands
o release bus dma resources on detach so module usage doesn't leak
o remove public key op disable now that bus dma memory allocation is fixed
o collect attach error handling in one place
Sponsored by: Vernier Networks
_nexus_dmamap_load_buffer()
- implement nexus_dmamap_load() in terms of _nexus_dmamap_load_buffer().
Note that this is untested, as this code is not currently used (but
might be later for UPA devices).
- move BUS_DMAMAP_NSEGS to bus_private.h
- disable the ecache flushing in nexus_dmamap_sync(); it should not be
needed, although the docs are not entirely clear on that.
some trick is necessary to prevent further BSD geoms from attaching to
that. Our old trick was to make sure we don't attach to a geom from
the "BSD" class, but this doesn't work if an intermediary geom obscures
this fact. Instead, calculate the MD5 checksum of the label we target
and ask if anybody below us loves that label. If they do we don't.
Coded by: gordon.
- move some constants into iommureg.h
- correct some comments
- use KASSERT() in one place instead of rolling our own
- take a sanity check out of #ifdef DIAGNOSTIC
- fix a syntax error in normally #ifdef'ed out debug code
- tweak the announce message a bit
- remove '\n's from a few panic() calls
- don't use the DVMA base adress the firmware reports; instead, figure
it out from the appropriate register on Sabres and let the IOMMU code
choose it on Psychos. This also makes the IOMMU TSB size freely
selectable.
2.) pass the requesting child device (instead of the bus one) up when
handling interrupt resources
3.) remeber to mark the resource list entry as unused in
sbus_release_resource().
Reported by: scottl (3)
The leak in lseek was introduced in vfs_syscalls.c revision 1.218.
The leak in do_dup was introduced in kern_descrip.c revision 1.158.
Submitted by: iedowse
Otherwise, the scsi devices that it is trying to issue commands to may
have gone away. This is what caused shutdown to hang on ia64 systems
with mpt scsi controllers. The bus system has torn down the device tree
and reset the mpt controller etc, and suddenly along comes dashutdown
and wants to issue a few more scsi commands.... <HANG!>
This shouldn't work on i386 either, but it seems to work solely due
to luck.
Add support for GCC's --test-coverage --profile-arcs options.
Add code to call the functions listed in the .ctors section, these are
used to string the per .o file counter blocks into a linked list.
Add empty __bb_fork_func() to cope with GCC magic gandling of exec*()
named functions.
To add support for other platforms should be trivial, but involves
determining the exact data-types gcc uses on that platform.
Minimum Acceptable Value: _POSIX_LOGIN_NAME_MAX.
The comments at the bottom of this file claim sysconf(3) provides this value,
but it seems sysconf(3) hasn't implemented this yet.
and declare them extern in interrupt.c. This eliminates the need
for ia64_add_sapic(), which is called from sapic.c.
While here, reformat ia64_enable() in interrupt.c to improve
indentation and add a sysctl (machdep.apic) to dump the I/O APIC
entries currently programmed into all I/O APICs. The latter can
help analyze interrupt problems.
Note that the sysctl is not intended as a userland (software)
interface. It may be changed in the future to include counters
so that vmstat -i can make use of it. It may also be removed...
copies of the reload. Note that we use the precomputed itm_reload value
so that we can avoid a division in the kernel. The ia64 cpu does not
have integer divide, so this would have been done by a floating point
operation.
CLOCK_VECTOR and define it as 254, not 255. Vector 255 is already
in use as the AP wakeup vector on the HP rx2600.
This needs to be made more dynamic. The likelyhood of vector 254
being in use is pretty small, but we already have code to assign
vectors to IPIs (see sal.c) and it's preobably better to have a
centralized "vector manager" that hands out vectors based on
some imput (like priority).
called. Otherwise (depending on a non-deterministic sort), the timecounter
code can be initialized before the clock rate has been set (on ia64) and it
assumes hz = 100, rather than the real value of 1024. I'm not sure how much
gets upset by this.
Glanced at by: phk
handleclock itself is trivial.
While here, replace (itc_frequency+hz/2)/hz with itm_reload for
consistency. There's now a single place where we determine the
ITM reload value.
header with M_MOVE_PKTHDR one should not reference the packet header in the
original packet; in this case the code was assuming that m_adj would alter
m_pkthdr.len which stopped happening because M_MOVE_PKTHDR removes the
M_PKTHDR bit from m_flags
Submitted by: Bill Fenner <fenner@research.att.com>
interrupt block). We use the previously hardcoded address as a
default only, but will otherwise use whatever ACPI tells us.
The address can be found in the MADT table header or in the
LAPIC override table entry.
space most of the time, but handles machines with lots of I/O
(S)APICs. We cannot make this more dynamic without breaking the
interface with vmstat. Hence, we need to fix the interface first.
name of unused entries from "intr XXX" to "#XXX". This makes it
easier to debug interrupt problems, because vmstat can be hacked
more easily to dump all interrupt entries that are in use and not
those that have had interrupts.
devices aren't necessarily mapped within 4GB. I/O port addresses
are offsets into the memory mapped I/O port space, which is not
larger than 16MB. No need to convert those to 64 bit types.
Previously all filesystems which relied on specfs to do devices
would have private overrides for vop_std*, so the vop_no* overrides
here had no effect. I overlooked the transitive nature of the vop
vectors when I removed the vop_std* in those filesystems.
Removing the override here restores device node locking to it's
previous modus operandi.
Spotted by: bde
