o add a new facility for components to register send+recv handlers
o ieee80211_send_action and ieee80211_recv_action now use the registered
handlers to dispatch operations
o rev ieee80211_send_action api to enable passing arbitrary data
o rev ieee80211_recv_action api to pass the 802.11 frame header as it may
be difficult to locate
o update existing IEEE80211_ACTION_CAT_BA and IEEE80211_ACTION_CAT_HT handling
o update mwl for api rev
Reviewed by: rpaulo
Approved by: re (kensmith)
o do not attach DLT_IEEE802_11_RADIO unless both tx and rx headers are
present; this is assumed in the capture code paths
o verify the above with asserts in ieee80211_radiotap_{rx,tx}
o add missing checks for active taps before calling ieee80211_radiotap_rx
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
For receive:
o explicitly tag rx frames w/ M_AMPDU instead of passing frames through
the reorder processing according to the node having HT and the frame
being QoS data
o relax ieee80211_ampdu_reorder asserts to allow any frame to be passed
in, unsuitable frames are returned to the caller for normal processing;
this permits drivers that cannot inspect the PLCP to mark all data
frames as potential ampdu candidates with only a small penalty
o add M_AMPDU_MPDU to identify frames resubmitted from the reorder q
For transmit:
o tag aggregation candidates with M_AMPDU_MPDU
o fix the QoS ack policy set in ampdu subframes; we only support immediate
BA streams which should be marked for "normal ack" to get implicit block
ack behaviour; interestingly certain vendor parts BA'd frames with the
11e BA ack policy set
o do not assign a sequence # to aggregation candidates; this must be done
when frames are submitted for transmit (NB: this can/will be handled
better when aggregation is pulled up to net80211)
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
