- Add support for ISA based DPT adapters (this doesn't quite work yet).
- Sync dpt_eisa.c with my local copy.
- Simplify how EISA IDs are matched.
- Prototype.
- Formatting nits.
- Conform to how I do things in dpt_pci.c/dpt_isa.c.
- Modify dpt_scsi.c:dpt_alloc() to DTRT with newbus.
- Add some comments to dpt_scsi.c:dpt_pio_get_conf().
- Add additional check to dpt_scsi.c:dpt_get_conf().
- Add some useful error messages to dpt_scsi.c:dpt_init().
request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
line in files or files.${arch} instead of 13 lines of code.
This is a small chance that this will break the alpha kernel build - I'll
fix it this evening if it does.
connected during boot and the vpo module is in the kernel/loaded.
In the case where the module is loaded at some later stage with kldload,
the CAM bus is now rescanned as well.
- The driver now uses bus_space() and runs on NetBSD 1.4.2
Submitted by Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
- Remove startup quirks for video and vbi capture for PAL users.
PAL TV users can now run FXTV and Alevt in any order.
- Add support for cable channels >100
Submitted by Scott Presnell <srp@zgi.com>
- New MSP3410/3415 setup code added. This is experimental.
Please set the sysctl hw.bt848.slow_msp_audio to 1 for this.
Submitted by Frank Nobis<fn@radio-do.de>
It was not a good idea to remove csu_header from struct cspace, it had
ramifications which I didn't notice.
Restore src/usr.sbin/ppp/slcompress.h to the way it was, since MAX_HDR
was already defined as 128 there and it's a user program anyway.
In sys/net/slcompress.h make MAX_HDR 128 intead of MLEN to avoid
bloat.
My apologies for any inconvenience.
Pass sc->dev rather than a bogusly cast pccard_softc *sc.
This allows us to insert and remove cards w/o panicing the kernel.
However, the cis isn't mapped in, so the pccard_scan_cis function
fails.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
tree. This considerably reduces unnecessary bloat in struct slcompress.
I'm running with this change right now and have seen no negative
side-effects.
On my sytem this reduced kernel BSS by about 25KB.
Submitted by: bde
Approved by: brian for user-ppp
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
