RFC 8200 says:
"If the fragment is a whole datagram (that is, both the Fragment
Offset field and the M flag are zero), then it does not need
any further reassembly and should be processed as a fully
reassembled packet (i.e., updating Next Header, adjust Payload
Length, removing the Fragment header, etc.). .."
That means we should remove the fragment header and make all the adjustments
rather than just skipping over the fragment header. The difference should
be noticeable in that a properly handled atomic fragment triggering an ICMPv6
message at an upper layer (e.g. dest unreach, unreachable port) will not
include the fragment header.
Update the test cases to also test for an unfragmentable part. That is
needed so that the next header is properly updated (not just lengths).
MFC after: 3 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D22155
The memory range between VM_MAXUSER_ADDRESS and VM_MIN_KERNEL_ADDRESS is
reserved for devices currently, which are always mapped in TLB1, and
therefore do not exist in the kernel page table. Any page fault in this
range is therefore automatically a fatal fault.
Since TLB_MAXNEST is 3, the insert mask should only be 2 bits. Given that 2
bits counts to 4, and that we already have plenty of space wasted in
padding, make the nest level 4 to match the mask.
Freescale SoCs use a set of IRQs at the high end of the OpenPIC IRQ
list, not counted in the NIRQs of the Feature reporting register. Some
SoCs include a MSI inbound window in the PCIe controller configuration
registers as well, but some don't. Currently, this only handles the
SoCs *with* the MSI window.
There are 256 MSIs per MSI bank (32 per MSI IRQ, 8 IRQs per MSI bank).
The P5020 has 3 banks, yielding up to 768 MSIs; older SoCs have only one
bank.
On the RPi4, some of these IRQs are shared. Start moving toward a mode where
we accept that shared IRQs happen and simply ignore interrupts that are
seemingly for no reason.
I would like to be more verbose here, but my 30-minute assessment of the
current world order is that mapping a resource/rid to an actual IRQ number
(as found in FDT) data is not a simple matter. Determining if more than one
handler is attached to an IRQ is closer to feasible, but it's unclear which
way is the cleaner path. Beyond that, we're only really using it to be
slightly more verbose when something's going wrong, so for now just suppress
and drop a complaint-comment.
This was originally submitted (via freebsd-arm@) by Robert Crowston; the
additional verbosity was dropped by kevans@.
Submitted by: Robert Crowston <crowston@protonmail.com>
TVSENSE may not be ready by the time t4_fw_initialize returns and the
firmware returns 0 if the driver asks for the Vdd before the sensor is
ready.
MFC after: 1 week
Sponsored by: Chelsio Communications
This is what iwlwifi seems to do, and the previous behaviour triggered
firmware panics during transmit on a 9560.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Though we don't otherwise use firmware's offload capabilities, we need
to set this flag when the MAC header's size isn't a multiple of four.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
- Configure the scheduler only for the management queue.
- Fix a bug when enabling the schduler: the queues are specified using a
bitmask.
- Fix style in the area.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This is the multiqueue receive code required for 9000-series chips.
Note that we still only configure a single RX queue for now. Multiqueue
support will require MSI-X configuration and a scheme for managing a
global pool of RX buffers.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
For now iwm only ever uses queue 0 and the management queue, but my 9560
raises a software error interrupt during initialization if this flag is
not set. iwlwifi sets it for all 7000- and 8000-series hardware, so we
might as well do it unconditionally.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
The firmware for 9000-series and newer devices has a different receive
API which supports multiple queues.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Match such chips using the device ID. We should really be checking the
subdevice as well, since a smaller number of 9460 and 9560 devices
actually belong to a new series of devices and require different
firmware, but that will require some extra logic in iwm_attach().
Submitted by: lwhsu, Guo Wen Jun <blockk2000@gmail.com>
MFC after: 2 weeks
Convert existing device family checks to avoid assuming that the device
family is always one of IWM_DEVICE_FAMILY_7000 or _8000.
Submitted by: lwhsu, Guo Wen Jun <blockk2000@gmail.com>
MFC after: 2 weeks
Only perform the call when a qfull bit transitions. While here, avoid
assignments in declarations in iwm_mvm_rx_tx_cmd().
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This ensures that the driver softc reflects device capabilities as early
as possible, for use by device initialization code that is conditional
on certain capabilities.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Also ensure that the htole* macros are applied correctly when specifying
the segment length and upper address bits. No functional change
intended (unless you use iwm(4) on a big-endian machine).
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This is a standard required property for interrupt controllers, and present
on the bcm_lintc nodes for currently supported RPi models. For the RPi4, we
have both bcm_lintc as well as GIC-400, but only one may be active at a
time.
Don't probe bcm_lintc if it's missing the "interrupt-controller" property --
in RPi 4 DTS, the bcm_lintc node is actually missing this along with other
required interrupt properties. Presumably, if the earlier boot stages will
support switching to the legacy interrupt controller (as is suggested
possible by the documentation), the DTS will need to be updated to indicate
the proper interrupt-parent and hopefully also mark this node as an
interrupt-controller instead.
handlers can be greatly simplified. All the previous double
cycling and complex locking was added to avoid these functions
holding global PCB locks for extended period of time, preventing
addition of new entries.
in the network epoch, we can greatly simplify synchronization.
Remove all unneccesary epoch enters hidden under INP_INFO_RLOCK macro.
Remove some unneccesary assertions and convert necessary ones into the
NET_EPOCH_ASSERT macro.
x86 stack_save_td_running() can work safely only if IPI_TRACE is a
non-maskable interrupt. But at the moment FreeBSD/Xen does not provide
support for the NMI delivery mode. So, mark the functionality as
unsupported similarly to other platforms without NMI.
Maybe there is a way to provide a Xen-specific working
stack_save_td_running(), but I couldn't figure it out.
MFC after: 3 weeks
Sponsored by: Panzura
locking in udp_output() and udp6_output().
First, we select if we need read or write lock in PCB itself, we take
the lock and enter network epoch. Then, we proceed for the rest of
the function. In case if we need to modify PCB hash, we would take
write lock on it for a short piece of code.
We could exit the epoch before allocating an mbuf, but with this
patch we are keeping it all the way into ip_output()/ip6_output().
Today this creates an epoch recursion, since ip_output() enters epoch
itself. However, once all protocols are reviewed, ip_output() and
ip6_output() would require epoch instead of entering it.
Note: I'm not 100% sure that in udp6_output() the epoch is required.
We don't do PCB hash lookup for a bound socket. And all branches of
in6_select_src() don't require epoch, at least they lack assertions.
Today inet6 address list is protected by rmlock, although it is CKLIST.
AFAIU, the future plan is to protect it by network epoch. That would
require epoch in in6_select_src(). Anyway, in future ip6_output()
would require epoch, udp6_output() would need to enter it.
we lookup PCBs. Thus, do not enter epoch recursively in
in_pcblookup_hash() and in6_pcblookup_hash(). Same applies to
tcp_ctlinput() and tcp6_ctlinput().
This leaves several sysctl(9) handlers that return PCB credentials
unprotected. Add epoch enter/exit to all of them.
Differential Revision: https://reviews.freebsd.org/D22197
