since the former is defined everywhere. This cuts off some code not
necessary on non strict aligment arches.
Reviewed by: adrian
Sponsored by: Nginx, Inc.
* Added new action category IEEE80211_ACTION_CAT_SELF_PROT which is used by 11s
for Mesh Peering Management;
* Updated Self protected enum Action codes to start from 1 instead of 0
according to the standard spec;
* Removed old and wrong action categories IEEE80211_ACTION_CAT_MESHPEERING;
* Modified ieee80211_mesh.c and ieee80211_action.c to use the new action
category code;
* Added earlier verification code in ieee80211_input;
Approved by: adrian
* Moved old categories as specified by D4.0 to be action fields of MESH category
as specified in amendment spec;
* Modified functions to use MESH category and its action fields:
+ ieee80211_send_action_register
+ ieee80211_send_action
+ ieee80211_recv_action_register
+ieee80211_recv_action;
* Modified ieee80211_hwmp_init and hwmp_send_action so they uses correct
action fields as specified in amendment spec;
* Modified ieee80211_parse_action so that it verifies MESH frames.
* Change Mesh Link Metric to use one information element as amendment spec.
Draft 4.0 defined two different information elements for request and response.
Submitted by: monthadar@gmail.com
This supports both station and hostap modes:
* Station mode quiet time element support listens to quiet time
IE's and modifies the local quiet time configuration as appropriate;
* Hostap mode both obeys the locally configured quiet time period
and includes it in beacon frames so stations also can obey as needed.
Submitted by: Himali Patel <himali.patel@sibridgetech.com>
Sponsored by: Sibridge Technologies
This introduces struct ieee80211_rx_stats - which stores the various kinds
of RX statistics which a MIMO and non-MIMO 802.11 device can export.
It also fleshes out the mimo export to userland (node_getmimoinfo()).
It assumes that MIMO radios (for now) export both ctl and ext channels.
Non-11n MIMO radios are possible (and I believe Atheros made at least
one), so if that chipset support is added, extra flags to the
struct ieee80211_rx_stats can be added to extend this support.
Two new input functions have been added - ieee80211_input_mimo() and
ieee80211_input_mimo_all() - which MIMO-aware devices can call with
MIMO specific statistics.
802.11 devices calling the non-MIMO input functions will still function.
clean up parts of the *_recv_mgmt() functions.
- make sure appropriate counters are bumped and debug messages are printed
- order the unhandled subtypes by value and add a few missing ones
- fix some whitespace nits
- remove duplicate code in adhoc_recv_mgmt()
- remove a useless comment, probably left in while c&p
* bridge support (sam)
* handling of errors (sam)
* deletion of inactive routing entries
* more debug msgs (sam)
* fixed some inconsistencies with the spec.
* decap is now specific to mesh (sam)
* print mesh seq. no. on ifconfig list mesh
* small perf. improvements
Reviewed by: sam
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
o IEEE80211_IOC_CHANSWITCH fixups:
- restrict to hostap vaps
- return EOPNOTSUPP instead of EINVAL when applied to !hostap vap
or to a vap w/o 11h enabled
- interpret count of 0 to mean cancel the current CSA
Reviewed by: rpaulo, avatar
o track # bpf taps on monitor mode vaps instead of # monitor mode vaps
o spam monitor mode taps on tx/rx
o fix ieee80211_radiotap_rx_all to dispatch frames only if the vap is up
o while here print radiotap (and superg) state in show com
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
really was meant to be 256. Adjust usage accordingly and replace
bogus usage of this value in checking IEEE channel #'s.
NB: this causes an ABI change; ifconfig must be recompiled
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
o update 11n definitions to D2.0 spec
o add IEEE80211_CAPINFO_SPECTRUM_MGMT for DFS support
o add CSA ie definition for DFS support
o purge some unused definitions
o correct 802.11 reason and status codes
o correct reason code returned when a sta tries to associate to an
ap operating with WPA/RSN but without a WPA/RSN ie
Reviewed by: thompsa, avatar
Approved by: re (blanket wireless)
device and have had the crypto bits stripped from the 802.11 header
o strip mbuf flags in the rx path before passing up the stack
Reviewed by: thompsa, sephe, avatar
Approved by: re (blanket wireless)
operating channel and use this in the scan cache rather than directly using
ic_curchan. Some firmware cards can only do a full scan and so ic_curchan does
not have the correct value.
Also add IEEE80211_CHAN2IEEE to directly dereference ic_ieee from the channel
to be used in the fast path.
Reviewed by: sam, sephe
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
station exiting power save mode prepend them to the driver's
send q instead of appending them. This insures the packets
are not misordered wrt any packets already q'd for the station.
This corrects a problem noticed when using a VoIP phone talking
to an ath card in ap mode; the misordered packets caused noise.
Submitted by: "J.R. Oldroyd" <jr@opal.com>
MFC after: 2 weeks
o add IEEE80211_F_JOIN flag to ieee80211_fix_rate to indicate a station
is joining a BSS; this is used to control whether or not we over-write
the basic rate bit in the calculated rate set
o fix ieee80211_fix_rate to honor IEEE80211_F_DODEL when IEEE80211_F_DONEGO
is not specified (e.g. when joining an ibss network)
o on sta join always delete unusable rates from the negotiated rate set,
this was being done only ibss networks but is also needed for 11g bss
with mixed stations
o on sta join delete unusable rates from the bss node's rate set, not the
scan table entry's rate set
o when calculating a rate set for new neighbors in an ibss caculate a
negotiated rate set so drivers are not presented with rates they should
not use
Submitted by: Sepherosa Ziehau (w/ modifications)
Obtained from: DragonFly
MFC after: 1 month
