88b1e0bc5b
11 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Justin T. Gibbs
|
d7cff4ab97 |
Correct spelling errors.
Switch to handling bad SCSI status as a sequencer interrupt instead of having the kernel proccess these failures via the completion queue. This is done because: o The old scheme required us to pause the sequencer and clear critical sections for each SCB. It seems that these pause actions, if coincident with a sequencer FIFO interrupt, would result in a FIFO interrupt getting lost or directing to the wrong FIFO. This caused hangs when the driver was stressed under high "queue full" loads. o The completion code assumed that it was always called with the sequencer running. This may not be the case in timeout processing where completions occur manually via ahd_pause_and_flushwork(). o With this scheme, the extra expense of clearing critical sections is avoided since the sequencer will only self pause once all pending selections have cleared and it is not in a critical section. aic79xx.c Add code to handle the new BAD_SCB_STATUS sequencer interrupt code. This just redirects the SCB through the already existing ahd_complete_scb() code path. Remove code in ahd_handle_scsi_status() that paused the sequencer, made sure that no selections where pending, and cleared critical sections. Bad status SCBs are now only processed when all of these conditions are true. aic79xx.reg: Add the BAD_SCB_STATUS sequencer interrupt code. aic79xx.seq: When completing an SCB upload to the host, if we are doing this because the SCB contains non-zero SCSI status, defer completing the SCB until there are no pending selection events. When completing these SCBs, use the new BAD_SCB_STATUS sequencer interrupt. For all other uploaded SCBs (currently only for underruns), the SCB is completed via the normal done queue. Additionally, keep the SCB that is currently being uploaded on the COMPLETE_DMA_SCB list until the dma is completed, not just until the DMA is started. This ensures that the DMA is restarted properly should the host disable the DMA transfer for some reason. In our RevA workaround for Maxtor drives, guard against the host pausing us while trying to pause I/O until the first data-valid REQ by clearing the current snapshot so that we can tell if the transfer has completed prior to us noticing the REQINIT status. In cfg4data_intr, shave off an instruction before getting the data path running by adding an entrypoint to the overrun handler to also increment the FIFO use count. In the overrun handler, be sure to clear our LONGJMP address in both exit paths. Perform a few sequencer optimizations. aic79xx.c: Print the full path from the SCB when a packetized status overrun occurs. Remove references to LONGJMP_SCB which is being removed from firmware usage. Print the new SCB_FIFO_USE_COUNT field in the per-SCB section of ahd_dump_card_state(). The SCB_TAG field is now re-used by the sequencer, so it no longer makes sense to reference this field in the kernel driver. aic79xx.h: Re-arrange fields in the hardware SCB from largest size type to smallest. This makes it easier to move fields without changing field alignment. The hardware scb tag field is now down near the "spare" portion of the SCB to facilitate reuse by the sequencer. aic79xx.reg: Remove LONGJMP_ADDR. Rearrange SCB fields to match aic79xx.h. Add SCB_FIFO_USE_COUNT as the first byte of the SCB_TAG field. aic79xx.seq: Add a per-SCB "Fifos in use count" field and use it to determine when it is safe (all data posted) to deliver status back to the host. The old method involved polling one or both FIFOs to verify that the current task did not have pending data. This makes running down the GSFIFO very cheap, so we will empty the GSFIFO in one idle loop pass in all cases. Use this simplification of the completion process to prune down the data FIFO teardown sequencer for packetized transfers. Much more code is now shared between the data residual and transfer complete cases. Correct some issues in the packetized status handler. It used to be possible to CLRCHN our FIFO before status had fully transferred to the host. We also failed to handle NONPACKREQ phases that could occur should a CRC error occur during transmission of the status data packet. Correct a few big endian issues: aic79xx.c: aic79xx_inline.h: aic79xx_pci.c: aic79xx_osm.c: o Always get the SCB's tag via the SCB_GET_TAG acccessor o Add missing use of byte swapping macros when touching hscb fields. o Don't double swap SEEPROM data when it is printed. Correct a big-endian bug. We cannot assign a o When assigning a 32bit LE variable to a 64bit LE variable, we must be explict about how the words of the 64bit LE variable are initialized. Cast to (uint32_t*) to do this. aic79xx.c: In ahd_clear_critical_section(), hit CRLSCSIINT after restoring the interrupt masks to avoid what appears to be a glitch on SCSIINT. Any real SCSIINT status will be persistent and will immidiately reset SCSIINT. This clear should only get rid of spurious SCSIINTs. This glitch was the cause of the "Unexpected PKT busfree" status that occurred under high queue full loads Call ahd_fini_scbdata() after shutdown so that any ahd_chip_init() routine that might access SCB data will not access free'd memory. Reset the bus on an IOERR since the chip doesn't seem to reset to the new voltage level without this. Change offset calculation for scatter gather maps so that the calculation is correct if an integral multiple of sg lists does not fit in the allocation size. Adjust bus dma tag for data buffers based on 39BIT addressing flag in our softc. Use the QFREEZE count to simplify ahd_pause_and_flushworkd(). We can thus rely on the sequencer eventually clearing ENSELO. In ahd_abort_scbs(), fix a bug that could potentially corrupt sequencer state. The saved SCB was being restored in the SCSI mode instead of the saved mode. It turns out that the SCB did not need to be saved at all as the scbptr is already restored by all subroutines called during this function that modify that register. aic79xx.c: aic79xx.h: aic79xx_pci.c: Add support for parsing the seeprom vital product data. The VPD data are currently unused. aic79xx.h: aic79xx.seq: aic79xx_pci.c: Add a firmware workaround to make the LED blink brighter during packetized operations on the H2A. aic79xx_inline.h: The host does not use timer interrupts, so don't gate our decision on whether or not to unpause the sequencer on whether or not a timer interrupt is pending. |
||
Maxime Henrion
|
7a648f56cf |
I deserve a big pointy hat for having missed all those references
to bus_dmasync_op_t in my last commit. |
||
Jake Burkholder
|
ab89b20ced | Compile with PAE. | ||
|
Justin T. Gibbs
|
acae33b029 |
aic79xx.c:
Clear the LQICRC_NLQ status should it pop up after we have already handled the SCSIPERR. During some streaming operations this status can be delayed until the stream ends. Without this change, the driver would complain about a "Missing case in ahd_handle_scsiint". In the LQOBUSFREE handler... Don't return the LQOMGR back to the idle state until after we have cleaned up ENSELO and any status related to this selection. The last thing we need is the LQO manager starting another select-out before we have updated the execution queue. It is not clear whether the LQOMGR would, or would not start a new selection early. Make sure ENSELO is off prior to clearing SELDO by flushing device writes. Move assignment of the next target SCB pointer inside of an if to make the code clearer. The effect is the same. Dump card state in both "Unexpected PKT busfree" paths. In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1. That register only exists in the SCSI mode. Also set the mode explicitly to the SCSI mode after chip reset due to paranoia. Re-arrange code so that SXFRCTL1 is restored as quickly after the chip reset as possible. S/G structurs must be 8byte aligned. Make this official by saying so in our DMA tag. Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come true. This can cause a CIO bus lockup if a PCI or PCI-X error occurs while the stretch is occurring - the host cannot service the PCI-X error since the CIO bus is locked out and SHVALID will never resolve. The stretch was added in the Rev B to simplify the wait for SHVALID to resolve, but the code to do this in the open source sequencer is so simple it was never removed. Consistently use MAX_OFFSET for the user max syncrate set from non-volatile storage. This ensures that the offset does not conflict with AH?_OFFSET_UNKNOWN. Have ahd_pause_and_flushwork set the mode to ensure that it has access to the registers it checks. Also modify the checking of intstat so that the check against 0xFF can actually succeed if the INT_PEND mask is something other than 0xFF. Although there are no cardbus U320 controllers, this check may be needed to recover from a hot-plug PCI removal that occurs without informing the driver. Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes an infinite loop at card initialization if the cacheline size is 0. aic79xx.h: Add AHD_EARLY_REQ_BUG bug flag. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the curr->offset can never be, unlike '0' which we previously used. This fixes code that only checks for a non-zero offset to determine if a sync negotiation is required since it will fire in the unknown case even if the goal is async. aic79xx.reg: Add comments for LQISTAT bits indicating their names in the 7902 data book. We use slightly different and more descriptive names in the firmware. Fix spelling errors. Include the CDB's length just after the CDB pointer in the DMA'ed CDB case. aic79xx.seq: Update comments regarding rundown of the GSFIFO to reflect reality. Fix spelling errors. Since we use an 8byte address and 1 byte length, shorten the size of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes. Remove code that, assuming the abort pending feature worked, would set MK_MESSAGE in the SCB's control byte on completion to catch invalid reselections. Since we don't see interrupts for completed selections, this status update could occur prior to us noticing the SELDO. The "select-out" queue logic will get confused by the MK_MESSAGE bit being set as this is used to catch packatized connections where we select-out with ATN. Since the abort pending feature doesn't work on any released controllers yet, this code was never executed. Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ assertions just because they were asserted within the bus settle delay window. This allows us to tolerate devices like the GEM318 that violate the SCSI spec. Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit should have no effect, but who knows... On the Rev A, we must wait for HDMAENACK before loading additional segments to avoid clobbering the address of the first segment in the S/G FIFO. This resolves data-corruption issues with certain IBM (now Hitachi) and Fujitsu U320 drives. Rearrange calc_residual to avoid an extra jmp instruction. On RevA Silicon, if the target returns us to data-out after we have already trained for data-out, it is possible for us to transition the free running clock to data-valid before the required 100ns P1 setup time (8 P1 assertions in fast-160 mode). This will only happen if this L-Q is a continuation of a data transfer for which we have already prefetched data into our FIFO (LQ/Data followed by LQ/Data for the same write transaction). This can cause some target implementations to miss the first few data transfers on the bus. We detect this situation by noticing that this is the first data transfer after an LQ (LQIWORKONLQ true), that the data transfer is a continuation of a transfer already setup in our FIFO (SAVEPTRS interrupt), and that the transaction is a write (DIRECTION set in DFCNTRL). The delay is performed by disabling SCSIEN until we see the first REQ from the target. Only compile in snapshot savepointers handler for RevA silicon where it is enabled. Handle the cfg4icmd packetized interrupt. We just need to load the address and count, start the DMA, and CLRCHN once the transfer is complete. Fix an oversight in the overrun handler for packetized status operations. We need to wait for either CTXTDONE or an overrun when checking for an overrun. The previous code did not wait and thus could decide that no overrun had occurred even though an overrun will occur on the next data-valid req. Add some comment to this section for clarity. Use LAST_SEG_DONE instead of LASTSDONE for testing transfer completion in the packetized status case. LASTSDONE may come up more quickly since it only records completion on the SCSI side, but since LAST_SEG_DONE is used everywhere else (and needs to be), this is less confusing. Add a missing invalidation of the longjmp address in the non-pack handler. This code needs additional review. aic79xx_inline.h: Fix spelling error. aic79xx_osm.c: Set the cdb length for CDBs dma'ed from host memory. Add a comment indicating that, should CAM start supporting cdbs larger than 16bytes, the driver could store the CDB in the status buffer. aic79xx_pci.c: Add a table entry for the 39320A. Added a missing comma to an error string table. Fix spelling errors. |
||
|
Justin T. Gibbs
|
0794987d01 |
aic79xx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
Save and restore the NEGOADDR address when setting
new transfer settings. The sequencer performs lookups
in the negotiation table too and it expects NEGOADDR
to remain consistent across pause/unpause sessions.
Consistently use "offset" instead of "period" to determine
if we are running sync or not.
Add a SHOW_MESSAGES diagnostic for when we assert ATN
during message processing.
Print out IU, QAS, and RTI features when showing transfer options.
Limit the syncrate after all option conformance
changes have taken place in ahd_devlimited_syncrate.
Changes in options may change the final syncrate we
accept.
Keep a copy of the hs_mailbox in our softc so that
we can perform read/modify/write operations on the
hs_mailbox without having to pause the sequencer to
read the last written value. Use the ENINT_COALESS
flag in the hs_mailbox to toggle interrupt coalessing.
Add entrypoints for enabling interrupt coalessing and
setting both a timeout (how long to wait for commands
to be coalessed) and a maximum commands to coaless value.
Add a statistics timer that decides when to enable or
disable interrupt coalessing based on load.
Add a routine, ahd_reset_cmds_pending() which is used
to update the CMDS_PENDING sequencer variable whenever
error recovery compeltes SCBs without notifying the
sequencer. Since ahd_reset_cmds_pending is called
during ahd_unpause() only if we've aborted SCBs, its
call to ahd_flush_qoutfifo should not cause recursion
through ahd_run_qoutfifo(). A panic has been added to
ensure that this recursion does not occur.
In ahd_search_qinfifo, update the CMDS_PENDING sequencer
variable directly. ahd_search_qinififo can be called
in situations where using ahd_reset_cmds_pending() might
cause recursion. Since we can safely determine the
exact number to reduce CMDS_PENDING by in this scenario
without running the qoutfifo, the manual update is sufficient.
Clean up diagnostics.
Add ahd_flush_qoutfifo() which will run the qoutfifo
as well as complete any commands sitting on the
sequencer's COMPLETE_SCB lists or the good status FIFO.
Use this routine in several places that did similar
things in an add-hoc, but incomplete, fashion. A call
to this routine was also added to ahd_abort_scbs() to
close a race.
In ahd_pause_and_flushwork() only return once selections
are safely disabled. Flush all completed commands via
ahd_flush_qoutfifo().
Remove "Now packetized" diagnostic now that this
information is incorperated into the actual negotiation
messages that are displayed.
When forcing renegotiation, don't clober the current
ppr_options. Much of the driver uses this information
to determine if we are currently packetized or not.
Remove some stray spaces at column 1 in ahd_set_tags.
When complaining about getting a host message loop
request with no pending messages, print out the
SCB_CONTROL register down on the card.
Modify the ahd_sent_msg() routine to handle a search
for an outgoing identify message. Use this to detect
a msg reject on an identify message which typically
indicates that the target thought we were packetized.
Force a renegotiation in this case.
In ahd_search_qinfifo(), wait more effectively for SCB
DMA activities to cease. We also disable SCB fetch
operations since we are about to change the qinfifo
and any fetch in progress will likely be invalidated.
In ahd_qinfifo_count(), fix the qinfifo empty case.
In ahd_dump_card_state(), print out CCSCBCTL in the
correct mode.
If we are a narrow controller, don't set the current
width to unknown when forcing a future negotiation.
This just confuses the code into attempting a wide
negotiation on a narrow bus.
Add support for task management function completions.
Modify ahd_handle_devreset so that it can handle
lun resets in addition to target resets. Use
ahd_handle_devreset for lun and target reset task
management functions.
Handle the abort task TMF race case better. We now
wait until any current selections are over and then
set the TMF back to zero. This should cause the sequencer
to ignore the abort TMF completion should it occur.
Correct a bug in the illegal phase handler that
caused us to drop down to narrow when handling the
unexpected command phase case after 3rd party
reset of a packetized device.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
aic79xx.h:
Add coalessing and HS_MAILBOX fields.
Add per-softc variables for the stats "daemon".
Add a debug option for interrupt coalessing activities.
Add two new softc flags:
o AHD_UPDATE_PEND_CMDS
Run ahd_reset_cmds_pending() on the next unpause.
o AHD_RUNNING_QOUTFIFO
Used to catch recursion through ahd_run_qoutfifo().
aic79xx.reg:
Correct register addresses related to the software timer
and the DFDBCTL register.
Add constants paramaterizing the software timer.
Add scratch ram locations for storing interrupt coalessing
tunables.
Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2.
In at least the REV A, these are writable bits. We make
use of that for a swtimer workaround in the sequencer.
Since HS_MAILBOX autoclears, provide a sequencer variable
to store its contents.
Add SEQINT codes for handling task management completions.
aic79xx.seq:
Correct ignore wide residue processing check for
a wide negotiation being in effect. We must be
in the SCSI register window in order to access the
negotiation table.
Use the software timer and a commands completed count to
implement interrupt coalessing. The command complete is
deferred until either the maximum command threshold or a
the expiration of a command deferral timer. If we have
more SCBs to complete to the host (sitting in COMPLETE_SCB
lists), always try to coaless them up to our coalessing limit.
If coalessing is enabled, but we have fewer commands oustanting
than the host's min coalessing limit, complete the command
immediately.
Add code to track the number of commands outstanding.
Commands are outstanding from the time they are placed
into the execution queue until the DMA to post completion
is setup.
Add a workaround for intvec_2 interrupts on the H2A4.
In H2A4, the mode pointer is not saved for intvec2, but
is restored on iret. This can lead to the restoration
of a bogus mode ptr. Manually clear the intmask bits and
do a normal return to compensate. We use intvec_2 to
track interrupt coalessing timeouts.
Since we cannot disable the swtimer's countdown, simply
mask its interrupt once we no longer care about it firing.
In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime
we are notified of an HS_MAILBOX update via the
HS_MAILBOX_ACT bit in QOFF_CTLSTA. We have to use a
local copy of persistant portions of the HS_MAILBOX as
the mailbox auto-clears on any read.
Move the test for the cfg4istat interrupt up an instruction
to hopefully close a race between the next outgoing selection
and our disabling of selections.
Add a missing ret to the last instruction in load_overrun_buf.
Add notifications to the host of task management
completions as well as the completions for commands
that completed successfully before their corresponding
TMF could be sent.
Hold a critical section during select-out processing
until we have a fully identified connection. This
removes a race condition with the legacy abort handler.
Correct a few spelling errors in some comments.
aic79xx_inline.h:
Call ahd_reset_cmds_pending() in ahd_unpause if required.
Update cmdcmplt interrupt statistics in our interrupt
handler.
Allow callers to ahd_send_scb() to set the task management
function.
aic79xx_pci.c:
Disable SERR and pause the controller prior to performing
our mmapped I/O test. The U320 controllers do not support
"auto-access-pause".
aic79xx_osm.c:
Set the task management function now that
ahd_send_scb() doesn't do it for us. We
also perform a lun reset in response to BDR
requests to packetized devices.
|
||
Scott Long
|
de5305d5b6 |
Synchronize perforce Id tags
Approved by: re (blanket) |
||
|
Scott Long
|
29dcbe8760 |
Revisit the printf format fixes for alpha. intmax_t doesn't exist in
RELENG_4, so cast to u_long in order to stay compatible. Approved by: re (blanket) |
||
|
Scott Long
|
cec762959b |
Fix printf format problems that were stopping LINT on alpha
Submitted by: jmallett, many others Approved by: re |
||
|
Justin T. Gibbs
|
c1463ef7c0 |
Enable card interrupts in our OSM rather than in the core.
This ensures that we don't enter our interrupt handler until all OSM components it might reference have been fully initialized during attach. Remove vestiges of untagged queue handling. Add hints to ahd_get_scb() so it knows what type of SCB collision management to perform for each new transaction. Properly disable/enable IU_REQ with changes in tagged queuing and disconnection settings passed in by CAM. |
||
|
Justin T. Gibbs
|
cdd49e97b4 | Hook up the ahd driver. | ||
|
Justin T. Gibbs
|
17d2475554 |
Enter the ahd driver which supports the Adaptec AIC7902 Ultra320, PCI-X
SCSI Controller chip. |