the system. Also, decrease the poll interval to 10 seconds from 30
seconds. This is needed because some systems will report an invalid high
temperature for one poll cycle. It is suspected this is due to the
embedded controller timing out. A typical value is 138C for one cycle on a
system that is otherwise 65C. This prevents the system from prematurely
shutting down after one invalid reading. It will still shut down after 30
seconds of high temperature, which is the same as previous default
behavior.
Tested by: Scott Lambert <lambert AT lambertfam.org>
This commit also removes the support for the sysutils/jailer port. This
is inline with the general policy to keep ports related knobs out
of the base system's configuration mechanism.
Submitted by: Juergen Unger <j.unger@addict.de>
is for an 802.11 device or not. At least one driver I have does not
support the OID_802_11_NETWORK_TYPES_SUPPORTED OID.
Also, for now, don't do anything special in the ndis_suspend() method.
I originally wanted to shut down the NIC but leave the IFF_UP flag alone
since technically the interface is meant to remain up, but an interrupt
may be delivered to the ISR on suspend, and if this happens while the
NIC is halted, we will crash, since none of the miniport driver methods
will function.
This needs to be dealt with properly later, but for now this prevents
a panic, and the resume method properly re-inits the NIC.
the thread that calls pmap_pte_quick() and by virtue of the page queues
lock being held, we can manage PADDR1/PMAP1 as a CPU private mapping.
The most common effect of this change is to reduce the overhead of the page
daemon on multiprocessors.
In collaboration with: tegge
packet along with data, instead of in their own packet. When serving files
of size (packetsize - headersize) or smaller, this will result in one less
packet crossing the network. Quick testing with thttpd and http_load has
shown a noticeable performance improvement in this case (350 vs 330 fetches
per second.)
Included in this commit are two support routines, iov_to_uio, and m_uiotombuf;
these routines are used by sendfile to construct the header mbuf chain that
will be linked to the rest of the data in the socket buffer.
sense with sched_4bsd as it does with sched_ule.
- Use P_NOLOAD instead of the absence of td->td_ithd to determine whether or
not a thread should be accounted for in sched_tdcnt.
when uma_reclaim() was called. This was introduced when the zone
working-set algorithm was removed in favor of using the per cpu caches
as the working set.
would allocate two 'struct pipe's from the pipe zone, and malloc a
mutex.
- Create a new "struct pipepair" object holding the two 'struct
pipe' instances, struct mutex, and struct label reference. Pipe
structures now have a back-pointer to the pipe pair, and a
'pipe_present' flag to indicate whether the half has been
closed.
- Perform mutex init/destroy in zone init/destroy, avoiding
reallocating the mutex for each pipe. Perform most pipe structure
setup in zone constructor.
- VM memory mappings for pageable buffers are still done outside of
the UMA zone.
- Change MAC API to speak 'struct pipepair' instead of 'struct pipe',
update many policies. MAC labels are also handled outside of the
UMA zone for now. Label-only policy modules don't have to be
recompiled, but if a module is recompiled, its pipe entry points
will need to be updated. If a module actually reached into the
pipe structures (unlikely), that would also need to be modified.
These changes substantially simplify failure handling in the pipe
code as there are many fewer possible failure modes.
On half-close, pipes no longer free the 'struct pipe' for the closed
half until a full-close takes place. However, VM mapped buffers
are still released on half-close.
Some code refactoring is now possible to clean up some of the back
references, etc; this patch attempts not to change the structure
of most of the pipe implementation, only allocation/free code
paths, so as to avoid introducing bugs (hopefully).
This cuts about 8%-9% off the cost of sequential pipe allocation
and free in system call tests on UP and SMP in my micro-benchmarks.
May or may not make a difference in macro-benchmarks, but doing
less work is good.
Reviewed by: juli, tjr
Testing help: dwhite, fenestro, scottl, et al
track the load for the sched_load() function. In the SMP case this member
is not defined because it would be redundant with the ksg_load member
which already tracks the non ithd load.
- For sched_load() in the UP case simply return ksq_sysload. In the SMP
case traverse the list of kseq groups and sum up their ksg_load fields.
of sched_load(). This variable tracks the number of running and runnable
non ithd threads. This removes the need to traverse the proc table and
discover how many threads are runnable.
from the sdl because strlcpy requires that the source string be
NUL-terminated unlike strncpy.
Submitted by: Peter Jeremy <PeterJeremy at optushome dot com dot au>
