determining the softc of the bridge in psycho_route_interrupt(). [1]
While at it, update the corresponding comment that the code in
question is also necessary for U30s in addition to E450s (a fact
that has been known for ages).
PR: 218478
Submitted by: Yoshihiko Iwama
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
This allows the PCI-PCI bridge driver to save a reference to the child
device in its softc.
Note that this required moving the "pci" device creation out of
acpi_pcib_attach(). Instead, acpi_pcib_attach() is renamed to
acpi_pcib_fetch_prt() as it's sole action now is to fetch the PCI
interrupt routing table.
Differential Revision: https://reviews.freebsd.org/D6021
Rescanning a PCI bus uses the following steps:
- Fetch the current set of child devices and save it in the 'devlist'
array.
- Allocate a parallel array 'unchanged' initalized with NULL pointers.
- Scan the bus checking each slot (and each function on slots with a
multifunction device).
- If a valid function is found, look for a matching device in the 'devlist'
array. If a device is found, save the pointer in the 'unchanged' array.
If a device is not found, add a new device.
- After the scan has finished, walk the 'devlist' array deleting any
devices that do not have a matching pointer in the 'unchanged' array.
- Finally, fetch an updated set of child devices and explicitly attach any
devices that are not present in the 'unchanged' array.
This builds on the previous changes to move subclass data management into
pci_alloc_devinfo(), pci_child_added(), and bus_child_deleted().
Subclasses of the PCI bus use custom rescan logic explicitly override the
rescan method to disable rescans.
Differential Revision: https://reviews.freebsd.org/D6018
The ACPI and OFW PCI bus drivers as well as CardBus override this to
allocate the larger ivars to hold additional info beyond the stock PCI ivars.
This removes the need to pass the size to functions like pci_add_iov_child()
and pci_read_device() simplifying IOV and bus rescanning implementations.
As a result of this and earlier changes, the ACPI PCI bus driver no longer
needs its own device_attach and pci_create_iov_child methods but can use
the methods in the stock PCI bus driver instead.
Differential Revision: https://reviews.freebsd.org/D5891
Instead of providing a wrapper around device_delete_child() that the PCI
bus and child bus drivers must call explicitly, move the bulk of the logic
from pci_delete_child() into a bus_child_deleted() method
(pci_child_deleted()). This allows PCI devices to be safely deleted via
device_delete_child().
- Add a bus_child_deleted method to the ACPI PCI bus which clears the
device_t associated with the corresponding ACPI handle in addition to
the normal PCI bus cleanup.
- Change cardbus_detach_card to call device_delete_children() and move
CardBus-specific delete logic into a new cardbus_child_deleted() method.
- Use device_delete_child() instead of pci_delete_child() in the SRIOV code.
- Add a bus_child_deleted method to the OpenFirmware PCI bus drivers which
frees the OpenFirmware device info for each PCI device.
Reviewed by: imp
Tested on: amd64 (CardBus and PCI-e hotplug)
Differential Revision: https://reviews.freebsd.org/D5831
On some architectures, u_long isn't large enough for resource definitions.
Particularly, powerpc and arm allow 36-bit (or larger) physical addresses, but
type `long' is only 32-bit. This extends rman's resources to uintmax_t. With
this change, any resource can feasibly be placed anywhere in physical memory
(within the constraints of the driver).
Why uintmax_t and not something machine dependent, or uint64_t? Though it's
possible for uintmax_t to grow, it's highly unlikely it will become 128-bit on
32-bit architectures. 64-bit architectures should have plenty of RAM to absorb
the increase on resource sizes if and when this occurs, and the number of
resources on memory-constrained systems should be sufficiently small as to not
pose a drastic overhead. That being said, uintmax_t was chosen for source
clarity. If it's specified as uint64_t, all printf()-like calls would either
need casts to uintmax_t, or be littered with PRI*64 macros. Casts to uintmax_t
aren't horrible, but it would also bake into the API for
resource_list_print_type() either a hidden assumption that entries get cast to
uintmax_t for printing, or these calls would need the PRI*64 macros. Since
source code is meant to be read more often than written, I chose the clearest
path of simply using uintmax_t.
Tested on a PowerPC p5020-based board, which places all device resources in
0xfxxxxxxxx, and has 8GB RAM.
Regression tested on qemu-system-i386
Regression tested on qemu-system-mips (malta profile)
Tested PAE and devinfo on virtualbox (live CD)
Special thanks to bz for his testing on ARM.
Reviewed By: bz, jhb (previous)
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D4544
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
drivers into the revived sys/sparc64/pci/ofw_pci.c, previously already
serving a similar purpose. This has been done with sun4v in mind, which
explains a) the otherwise not that obvious scheme employed and b) why
reusing sys/powerpc/ofw/ofw_pci.c was even lesser an option.
- Add a workaround for QEMU once again not emulating real machines, in
this case by not providing the OFW_PCI_CS_MEM64 range. [1]
Submitted by: jhb [1]
MFC after: 1 week
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
resume that is a superset of a pcb. Move the FPU state out of the pcb and
into this new structure. As part of this, move the FPU resume code on
amd64 into a C function. This allows resumectx() to still operate only on
a pcb and more closely mirrors the i386 code.
Reviewed by: kib (earlier version)
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
I/O windows, the default is to preserve the firmware-assigned resources.
PCI bus numbers are only managed if NEW_PCIB is enabled and the architecture
defines a PCI_RES_BUS resource type.
- Add a helper API to create top-level PCI bus resource managers for each
PCI domain/segment. Host-PCI bridge drivers use this API to allocate
bus numbers from their associated domain.
- Change the PCI bus and CardBus drivers to allocate a bus resource for
their bus number from the parent PCI bridge device.
- Change the PCI-PCI and PCI-CardBus bridge drivers to allocate the
full range of bus numbers from secbus to subbus from their parent bridge.
The drivers also always program their primary bus register. The bridge
drivers also support growing their bus range by extending the bus resource
and updating subbus to match the larger range.
- Add support for managing PCI bus resources to the Host-PCI bridge drivers
used for amd64 and i386 (acpi_pcib, mptable_pcib, legacy_pcib, and qpi_pcib).
- Define a PCI_RES_BUS resource type for amd64 and i386.
Reviewed by: imp
MFC after: 1 month
uart(4) allocates send and receiver buffers in attach() before it calls
the low-level driver's attach routine. Many low-level drivers set the
fifo sizes in their attach routine, which is too late. Other drivers set
them in the probe() routine, so that they're available when uart(4)
allocates buffers. This fixes the ones that were setting the values too
late by moving the code to probe().
interrupt shutdown handlers into filters. Shutdown_nice(9) acquires a sleep
lock, which filters shouldn't do. It also seems that kern_reboot(9) still
may require Giant to be hold.
Submitted by: bde
fail interrupt handler, there seems to be either a broken batch of them
or a tendency to develop a defect which causes this interrupt to fire
inadvertedly. Given that apart from this problem these machines work
just fine, add a tunable allowing the setup of the power fail interrupt
to be disabled.
While at it, remove the DEBUGGER_ON_POWERFAIL compile time option and
make that behavior also selectable via the newly added tunable.
- Apparently, it's no longer a problem to call shutdown_nice(9) from within
an interrupt filter (some other drivers in the tree do the same). So
change the power fail interrupt from an handler in order to simplify the
code and get rid of a !INTR_MPSAFE handler.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Use NULL instead of 0 for pointers.
- Let ofw_pcib_probe() return BUS_PROBE_DEFAULT instead of 0 so specialized
PCI-PCI-bridge drivers may attach instead.
- Add WARs for PLX Technology PEX 8114 bridges and PEX 8532 switches.
Ideally, these should live in MI code but at least for the latter we're
missing the necessary infrastructure there.
MFC after: 1 week
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
- Correctly determine the maximum payload size for setting the TX link
frequent NACK latency and replay timer thresholds.
Submitted by: stefanf [1]
MFC after: 3 days
DMA tag with a 4 GB boundary as required by PCI-Express. With r232403 in
place this actually is redundant. However, the host-PCI-Express bridge
driver is the more appropriate place for implementing this restriction.
MFC after: 3 days
The tag enforces a single restriction that all DMA transactions must not
cross a 4GB boundary. Note that while this restriction technically only
applies to PCI-express, this change applies it to all PCI devices as it
is simpler to implement that way and errs on the side of caution.
- Add a softc structure for PCI bus devices to hold the bus_dma tag and
a new pci_attach_common() routine that performs actions common to the
attach phase of all PCI bus drivers. Right now this only consists of
a bootverbose printf and the allocate of a bus_dma tag if necessary.
- Adjust all PCI bus drivers to allocate a PCI bus softc and to call
pci_attach_common() from their attach routines.
MFC after: 2 weeks
so try harder to get the CDMA sync interrupt delivered and also in
a more efficient way:
- wrap the whole process of sending and receiving the CDMA sync
interrupt in a critical section so we don't get preempted,
- send the CDMA sync interrupt to the CPU that is actually waiting
for it to happen so we don't take a detour via another CPU,
- instead of waiting for up to 15 seconds for the interrupt to
trigger try the whole process for up to 15 times using a one
second timeout (the code was also changed to just ignore belated
interrupts of a previous tries should they appear).
According to testing done by Peter Jeremy with the debugging also
added as part of this commit the first two changes apparently are
sufficient to now properly get the CDMA sync interrupts delivered
at the first try though.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
- Implement bus_adjust_resource() methods as far as necessary and in non-PCI
bridge drivers as far as feasible without rototilling them.
- As NEW_PCIB does a layering violation by activating resources at layers
above pci(4) without previously bubbling up their allocation there, move
the assignment of bus tags and handles from the bus_alloc_resource() to
the bus_activate_resource() methods like at least the other NEW_PCIB
enabled architectures do. This is somewhat unfortunate as previously
sparc64 (ab)used resource activation to indicate whether SYS_RES_MEMORY
resources should be mapped into KVA, which is only necessary if their
going to be accessed via the pointer returned from rman_get_virtual() but
not for bus_space(9) as the later always uses physical access on sparc64.
Besides wasting KVA if we always map in SYS_RES_MEMORY resources, a driver
also may deliberately not map them in if the firmware already has done so,
possibly in a special way. So in order to still allow a driver to decide
whether a SYS_RES_MEMORY resource should be mapped into KVA we let it
indicate that by calling bus_space_map(9) with BUS_SPACE_MAP_LINEAR as
actually documented in the bus_space(9) page. This is implemented by
allocating a separate bus tag per SYS_RES_MEMORY resource and passing the
resource via the previously unused bus tag cookie so we later on can call
rman_set_virtual() in sparc64_bus_mem_map(). As a side effect this now
also allows to actually indicate that a SYS_RES_MEMORY resource should be
mapped in as cacheable and/or read-only via BUS_SPACE_MAP_CACHEABLE and
BUS_SPACE_MAP_READONLY respectively.
- Do some minor cleanup like taking advantage of rman_init_from_resource(),
factor out the common part of bus tag allocation into a newly added
sparc64_alloc_bus_tag(), hook up some missing newbus methods and replace
some homegrown versions with the generic counterparts etc.
- While at it, let apb_attach() (which can't use the generic NEW_PCIB code
as APB bridges just don't have the base and limit registers implemented)
regarding the config space registers cached in pcib_softc and the SYSCTL
reporting nodes set up.
also use the streaming buffer of pre version 5/revision 2.3 hardware as
long as we stay away from context flushes (which iommu(4) so far doesn't
take advantage of). OpenSolaris does the same.
cycle mode as timecounter just works fine. My best guess is that a firmware
update has fixed this, check at run-time whether it advances and use a
positive quality if it does. The latter will cause this timecounter to be
used instead of the tick counter based one, which just sucks for SMP.
- Remove a redundant NULL assignment from the timecounter initialization.
as STX_CTRL_PERF_CNT_CNT0_SHIFT actually is zero, if we were using the
second counter in the upper 32 bits this would be required though as the MI
timecounter code doesn't support 64-bit counters/counter registers.
- Remove a redundant NULL assignment from the timecounter initialization.
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
