This uses the new firmware(9) method for squirreling away the EEPROM
contents from SPI flash so ath(4) can get to them later.
It won't work out of the box just yet - you have to add this to
if_ath_pci.c:
#define ATH_EEPROM_FIRMWARE
.. until I've added it as a configuration option and updated things.
future use by the ath(4) driver.
These embedded devices put the calibration/PCI bootstrap data on the
on board SPI flash rather than on an EEPROM connected to the NIC.
For some boards, there's two NICs and two sets of EEPROM data in the
main SPI flash.
The particulars:
* Introduce ath_fixup_size, which is the size of the EEPROM area in
bytes.
* Create a firmware image with a name based on the PCI device identifier
(bus/slot/device/function).
* Hide some verbose debugging behind 'bootverbose'.
ath(4) can then use this to load in the EEPROM data.
This requires AR71XX_ATH_EEPROM to be defined.
* the openwrt code doesn't treat 0/0/0 any differently
from other bus/slot/func combinations.
* A "local write" function writes to the LCONF area, and
so I've added it.
* The PCI workaround at attach time uses this LCONF code,
which it already did ..
* .. but it is a 4 byte write, not a 2 byte write.
Even though it's PCIR_COMMAND which is a two byte PCI register.
Tested on: AR7161
TODO: The other two AR71xx derivatives
TODO: More thoroughly stare at the datasheets I do have
and if it indeed is incorrect, push fixes to both
FreeBSD and Linux/OpenWRT.
Obtained from: Linux OpenWRT
This makes our naming scheme more closely match other systems and the
expectations of much third-party software. MIPS builds which are little-endian
should require and exhibit no changes. Big-endian TARGET_ARCHes must be
changed:
From: To:
mipseb mips
mipsn32eb mipsn32
mips64eb mips64
An entry has been added to UPDATING and some foot-shooting protection (complete
with warnings which should become errors in the near future) to the top-level
base system Makefile.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
The on-chip SD slots do not have PCI BARs corresponding to them, so
this has to be handled in the custom SoC memory allocation.
Provide memory resource for rids corresponding to BAR 0 and 1 in
the custom allocation code.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.
Move XLP PCI UART device to sys/mips/nlm/dev/ directory. Other
drivers for the XLP SoC devices will be added here as well.
Update uart_cpu_xlp.c and uart_pci_xlp.c use macros for uart port,
speed and IO frequency.
Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
- Replace MIPS24K-specific code with more generic framework that will
make adding new CPU support easier
- Add MIPS24K support for new framework
- Limit backtrace depth to 1 for stability reasons and add option
HWPMC_MIPS_BACKTRACE to override this limitation
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
These are needed for some particular port configurations where the default
speed isn't suitable for all link speed types. (Ie, changing 10/100/1000MBit
PLL rate requires a similar MII clock rate, rather than a fixed MII rate.)
This is:
* only currently implemented for the ar71xx;
* isn't used anywhere (yet), as the final interface for this hasn't yet
been determined.
function.
From the submitter:
This patch fixes an issue I encountered using an NFS root with an
ar71xx-based MikroTik RouterBoard 450G on -current where the kernel fails
to contact a DHCP/BOOTP server via if_arge when it otherwise should be able
to. This may be the same issue that Monthadar Al Jaberi reported against
an RSPRO on 6 March, as the signature is the same:
%%%
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
.
.
.
DHCP/BOOTP timeout for server 255.255.255.255
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
DHCP/BOOTP timeout for server 255.255.255.255
arge0: initialization failed: no memory for rx buffers
%%%
The primary issue that I found is that the DHCP/BOOTP message that
bootpc_call() is sending never makes it onto the wire, which I believe is
due to the following:
- Last December, a change was made to the ifioctl that bootpc_call() uses
to adjust the netmask around the sosend().
- The new ioctl (SIOCAIFADDR) performs an if_init when invoked, whereas the
old one (SIOCSIFNETMASK) did not.
- if_arge maintains its own sense of link state in sc->arge_link_status.
- On a single-phy interface, sc->arge_link_status is initialized to 0 in
arge_init_locked().
- sc->arge_link_status remains 0 until a phy state change notification
causes arge_link_task to run, notice the link is up, and set it to 1.
- The inits caused by the ifioctls in bootpc_call are reinitializing the
interface, but not the phy, so sc->arge_link_status goes to 0 and remains
there.
- arge_start_locked() always sees sc->arge_link_status == 0 and returns
without queuing anything.
The attached patch changes arge_init_locked() such that in the single-phy
case, instead of initializing sc->arge_link_status to 0, it runs
arge_link_task() to set it according to the current phy state. This change
has allowed my setup to mount an NFS root successfully.
Submitted by: Patrick Kelsey <kelsey@ieee.org>
Reviewed by: juli
