versions of controller support different number of ring control
blocks such that adjust code a bit to access known number of
send/receive ring control blocks. Previously bge(4) blindly
accessed 16 send/receive RCBs. Also move initializing standard
receive producer ring producer index, jumbo receive producer ring
producer index and mini receive producer ring producer index to
the end of each receive producer ring initialization.
Do not assume mini receive producer ring is available only when
controller has jumbo frame capability, instead explicitly check
ASIC version BCM5700 to disable mini receive producer ring.
Additionally always enable send ring 0 regardless of controller
versions. Previously bge(4) didn't enable send ring 0 if controller
is BGE_IS_5705_PLUS. Becase bge(4) need 1 send ring to send frames
at least, I have no idea how it would have worked so far.
Submitted by: davidch
dev.bce.<unit>.nvram_dump
Add the capability to write the complete contents of the NVRAM via sysctl
dev.bce.<unit>.nvram_write
These are only available if the kernel option BCE_DEBUG is enabled.
The nvram_write sysctl also requires the kernel option
BCE_NVRAM_WRITE_SUPPORT to be enabled. These are to be used at your
own caution. Since the MAC addresses are stored in the NVRAM, if you
dump one NIC and restore it on another NIC the destination NIC's
MAC addresses will not be preserved. A tool can be made using these
sysctl's to manage the on-chip firmware.
Reviewed by: davidch, yongari
BGE_MI_MODE register accesses. Previously bge(4) used to read
BGE_MI_MODE register to detect whether it needs to disable
autopolling feature or not. Because we don't touch autopolling in
other part of driver there is no reason to read BGE_MI_MODE
register given that we know default value in advance. In order to
achieve the goal, check whether the controller has CPMU(Central
Power Mangement Unit) capability. If controller has CPMU feature,
use 500KHz MII management interface(mdio/mdc) frequency regardless
core clock frequency. Otherwise use default MII clock. While I'm
here, add CPMU register definition.
In bge_miibus_readreg(), rearrange code a bit and remove goto
statement. In bge_miibus_writereg(), make sure to restore
autopolling even if MII write failed. The delay time inserted after
accessing BGE_MI_MODE register increased from 40us to 80us.
The default PHY address is now stored in softc. All PHYs supported
by bge(4) currently uses PHY address 1 but it will be changed when
we add newer controllers. This change will make it easier to change
default PHY address depending on PHY models.
Submitted by: davidch
special eject command to reappear as modem. It also requires DIR_IN flag
in the command message, so we supply some dummy data along with the command.
Feedback from X080S owners appreciated. I have not a pure Alcatel/TCTMobile
device, but another one under "Svyaznoy" (Связной) brand, and I didn't yet
managed to get it working. It is successfully recognized, it responds to
AT commands, but it shuts up right after successfull CONNECT response.
Reviewed by: hps
successfully received a frame but we failed to pass it to upper
stack due to lack of resources. So update if_iqdrops counter
instead of updating if_ierrors counter.
mode in the USB core. The patch mostly consists of updating the USB
HUB code to support USB 3.0 HUBs. This patch also add some more USB
controller methods to support more active-alike USB controllers like
the XHCI which needs to be informed about various device state events.
USB 3.0 HUBs are not tested yet, due to lack of hardware, but are
believed to work.
After this update the initial device descriptor is only read twice
when we know that the bMaxPacketSize is too small for a single packet
transfer of this descriptor.
Approved by: thompsa (mentor)
controllers combine multiple TX requests into single one if there
is room in TX buffer of controller. Updating TX packet counter at
the end of TX completion resulted in incorrect TX packet counter as
axe(4) thought it sent 1 packet. There is no easy way to know how
many combined TX were completed in the callback.
Because this change updates TX packet counter before actual
transmission, it may not be ideal one. But I believe it's better
than showing fake 8kpps under high TX load. With this change, TX
shows 221kpps on Linksus USB200M.
these names are used in data sheet. Also use UnicastPkts,
MulticastPkts and BroadcastPkts instead of UcastPkts, McastPkts
and BcastPkts to clarify its meaning.
Suggested by: bde
scratch. This driver adds support for USB3.0 devices. The XHCI
interface is also backwards compatible to USB2.0 and USB1.0 and will
evntually replace the OHCI/UHCI and EHCI drivers.
There will be follow-up commits during the coming week to link the
driver into the default kernel build and add missing USB3.0
functionality in the USB core. Currently only the driver files are
committed.
Approved by: thompsa (mentor)
different PHY instance being selected and isolation out into the wrappers
around the service methods rather than duplicating them over and over
again (besides, a PHY driver shouldn't need to care about which instance
it actually is).
- Centralize the check for the need to isolate a non-zero PHY instance not
supporting isolation in mii_mediachg() and just ignore it rather than
panicing, which should sufficient given that a) things are likely to
just work anyway if one doesn't plug in more than one port at a time and
b) refusing to attach in this case just leaves us in a unknown but most
likely also not exactly correct configuration (besides several drivers
setting MIIF_NOISOLATE didn't care about these anyway, probably due to
setting this flag for no real reason).
- Minor fixes like removing unnecessary setting of sc->mii_anegticks,
using sc->mii_anegticks instead of hardcoded values etc.
number of unexplained interrupt problems. For some reason, using HPET
interrupts there breaks HDA sound. Legacy route mode interrupts reported
to work fine there.
controllers. bge(4) exported MAC statistics on controllers that
maintain the statistics in the NIC's internal memory. Newer
controllers require register access to fetch these values. These
counters provide useful information to diagnose driver issues.
parent driver. Use that information to configure flow-control.
One drawback is there is no way to disable flow-control as we still
don't have proper way to not advertise RX/TX pause capability to
link partner. But I don't think it would cause severe problems and
users can selectively disable flow-control in switch port.
- license clause now contains "AUTHOR AND CONTRIBUTORS"
instead of just "AUTHOR"
- Add license/copyright to gpioc.c
Spotted by: Edward Tomasz Napierala, Andrew Turner
which were raised during hot-swap events. Now such events trigger cam
rescans, as is done in the mps driver.
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
has reached. This reduced number of dropped frames when
flow-control is enabled. Previously it dropped incoming frames once
RX MBUF low watermark has reached. The value used in MAC RX MBUF
low watermark is greater than or equal to 4 so receiving two more
RX frames should not be a problem.
Obtained from: OpenBSD
- GPIO bus controller interface
- GPIO bus interface
- Implementation of GPIO led(4) compatible device
- Implementation of iic(4) bus over GPIO (author: Luiz Otavio O Souza)
Tested by: Luiz Otavio O Souza, Alexandr Rybalko
- Sync shared code with Intel internal
- New client chipset support added
- em driver - fixes to 82574, limit queues to 1 but use MSIX
- em driver - large changes in TX checksum offload and tso
code, thanks to yongari.
- some small changes for watchdog issues.
- igb driver - local timer watchdog code was missing locking
this and a couple other watchdog related fixes.
- bug in rx discard found by Andrew Boyer, check for null pointer
MFC: a week
