some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
o do not put the chip into full sleep in ath_stop as it gains
nothing and causes many parts to hang in ath_detach because we
may touch the chip during vap teardown; this may also fix issues
with unloading the module
o add a note in ath_detach to explain ath_hal_detach puts the
chip in low power mode; this is useful to know as it means
unloading the module will place a pci device in the lowest
possible power state
o leave an #ifdef notyet marker for powering down the chip when
a device is marked down; we can't do that until we handle all
the ways the driver may be entered and touch the chip
o fix resume by reloading the h/w key cache as it's been clobbered
(for pci) by the socket being powered off; for station mode we
directly stop+init the chip and then simulate a beacon miss to
get the upper layers sync'd up; for other configs we must brute
force stop+start the vaps so they go through the state machine
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
previously conditionally acquired Giant based on debug.mpsafenet. As that
has now been removed, they are no longer required. Removing them
significantly simplifies error-handling in the socket layer, eliminated
quite a bit of unwinding of locking in error cases.
While here clean up the now unneeded opt_net.h, which previously was used
for the NET_WITH_GIANT kernel option. Clean up some related gotos for
consistency.
Reviewed by: bz, csjp
Tested by: kris
Approved by: re (kensmith)
framework for non-MPSAFE network protocols:
- Remove debug_mpsafenet variable, sysctl, and tunable.
- Remove NET_NEEDS_GIANT() and associate SYSINITSs used by it to force
debug.mpsafenet=0 if non-MPSAFE protocols are compiled into the kernel.
- Remove logic to automatically flag interrupt handlers as non-MPSAFE if
debug.mpsafenet is set for an INTR_TYPE_NET handler.
- Remove logic to automatically flag netisr handlers as non-MPSAFE if
debug.mpsafenet is set.
- Remove references in a few subsystems, including NFS and Cronyx drivers,
which keyed off debug_mpsafenet to determine various aspects of their own
locking behavior.
- Convert NET_LOCK_GIANT(), NET_UNLOCK_GIANT(), and NET_ASSERT_GIANT into
no-op's, as their entire behavior was determined by the value in
debug_mpsafenet.
- Alias NET_CALLOUT_MPSAFE to CALLOUT_MPSAFE.
Many remaining references to NET_.*_GIANT() and NET_CALLOUT_MPSAFE are still
present in subsystems, and will be removed in followup commits.
Reviewed by: bz, jhb
Approved by: re (kensmith)
where a device timeout that occurs with a mgt frame on the tx q
will leave the net80211 layer w/o any way to make progress.
Reviewed by: thompsa, sephe
Approved by: re (hrs)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
race seen on smp laptops when suspending where the rx task can be
entered after the interface is detach'd.
NB: use of taskqueue_drain while holding the softc mutex is problematic
Submitted by: ambrisko
MFC after: 1 month
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
for processing frames from the power save queue when operating
in ap mode. This is especially noticeable for realtime data going
to devices like voip phones.
Submitted by: "J.R. Oldroyd" <jr@opal.com>
MFC after: 2 weeks
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
o eliminate assumptions that half/quarter rate channels on exist in 11a
o handle frequency mapping between hal and net80211; hal gives us freq's
in the range 2422..2437 that we remap
MFC after: 1 month
o change handling of regdomain-related mib knobs so they can be set
post-attach: regdomain, countrycode, outdoor, and xchanmode; the
hal will not permit changing the regdomain but we expose it for now
o on regdomain/countrycode change recalculate the channel list and
push it to the net80211 layer (NB: looks to need more tweaking)
o setup rate tables for half/quarter rate channels
o honor half/quarter rate channel configs when changing channels
o honor half/quarter rate channel configs when setting the slot time
o use hack/nonstandard channel numbering scheme for the public safety
band to avoid overlapping 2.4G channels on dual-band cards
o remove setup of ic_sup_rates; the net80211 layer can do this for us
and it simplifies handling of half/quarter rate channels
Tested only in Public Safety Band with cards that have RF5112.
o no more ds_vdata in tx/rx descriptors
o split h/w tx/rx descriptor from s/w status
o as part of the descriptor split change the rate control module api
so the ath_buf is passed in to the module so it can fetch both
descriptor and status information as needed
o add some const poisoning
Also for sample rate control algorithm:
o split debug msgs (node, rate, any)
o uniformly bounds check rate indices (and in some cases correct checks)
o move array index ops to after bounds checking
o use final tsi from the status block instead of the h/w descriptor
o replace h/w descriptor struct's with proper mask+shift defs (this
doesn't belong here; everything is known by the driver and should
just be sent down so there's no h/w-specific knowledge)
MFC after: 1 month
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
