The -l flag sends only the READ CAPACITY (16) sevice action. Normally
we send the READ CAPACITY (10) command, and only send RC16 when the
capacity is larger than 2TB (since that's the max RC10 can
report). However, some badly programmed drives report different
numbers for RC10 and RC16. This can be hard to diagnose, but generally
there's a "Logical block address out of range" error when RC16 reports
a larger number than RC10 and the RC10 number is the correct one. By
comparing the output of readcap with and without the -l argmuent, one
can determine if there's a mismatch and if the DA_Q_NO_RC16 quirk is
needed.
Reviewed by: ken@
Differential Revision: https://reviews.freebsd.org/D19536
Implement MK_NVME now that the expression for where NVMe is
complicated. Default it to "yes" for x86 and powerpc64 and
no everywhere else. Use it in camcontrol to define WITH_NVME
for those platforms where we support nvme.
This should fix the newly introduced nvme files to camcontrol
which were building everywhere.
Pointy Hat To: imp
Sponsored by: Netflix
Both ATA and NVME have an identify command. They are completely
different, but to the user they are the same. Leverage nvmecontrol's
print_controller code to provide that functionality to camcontrol
identify. Query the path to see what kind of protocol it supports, and
send the most appropriate command down. Refactor nvme_print_dev a
little to make it easy to get the nvme cdata.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D15371
Report the NVMe spec, number of lanes (and max) as well as the PCIe
generation we're negotiated at (and max) for the camcontrol rate
command.
Reviewed by: scottl (the output, not the code)
Sponsored by: Netflix
Make it possible to retrieve mmc parameters via the XPT_GET_ADVINFO
call instead. Convert camcontrol to the new scheme.
Reviewed by: imp. kibab
Sponsored by: Netflix
Differential Revision: D13868
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
ZAC (Zoned-device ATA Command set) is the standard for addressing SMR
(shingled magnetic recording) devices over SATA. Drives indicate their
support for ZAC in their IDENTIFY block. Print whether and how a drive
supports ZAC in the output of "camcontrol identify".
Reviewed by: ken, imp
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D13171
- Delete trailing whitespace.
- Replace 8 single column spaces with hard tabs.
- Delete lines with consisting purely of blank space.
- Add space between `return` and `(`, per style(9).
Special care was taken to not blindly replace 8 single column spaces
with tabs; doing so could break tools that do strict string comparisons
with camcontrol output.
specific parameter.
Tape drives include write protect (WP), Buffered Mode and Speed
settings in the device-specific parameter. Clearing this
parameter on a mode select can have the effect of turning off
write protect or buffered mode, or changing the speed setting of
the tape drive.
Disks report DPO/FUA support via the device specific parameter
for MODE SENSE, but the bit is reserved for MODE SELECT. So we
clear this for disks (and other non-tape devices) to avoid
potential errors from the target device.
sbin/camcontrol/modeedit.c:
Clear the device-specific parameter in the mode page
header if we're not operating on a tape drive.
MFC after: 3 days
Sponsored by: Spectra Logic
name and unit number in camcontrol(8).
Previously camcontrol(8) only supported rescanning or resetting
devices specified by bus:target:lun. This is because for
rescanning at least, you don't have a peripheral name and unit
number (e.g. da4) for devices that don't exist yet.
That is still the case after this change, but in other cases, when
the device does exist in the CAM EDT (Existing Device Table), we
do a careful lookup of the bus/target/lun if the user supplies a
peripheral name and unit number to find the bus:target:lun and then
issue the requested reset or rescan.
The lookup is done without actually opening the device in question,
since a rescan is often done to make a device go away after it has
been pulled. (This is especially true for busses/controllers, like
parallel SCSI controllers, that don't automatically detect changes
in topology.) Opening a device that is no longer there to
determine the bus/target/lun might result in error recovery actions
when the user really just wanted to make the device go away.
sbin/camcontrol/camcontrol.c:
In dorescan_or_reset(), if the use hasn't specified a
numeric argument, assume he has specified a device. Lookup
the pass(4) instance for that device using the transport
layer CAMGETPASSTHRU ioctl. If that is successful, we can
use the returned bus:target:lun to rescan or reset the
device.
Under the hood, resetting a device using XPT_RESET_DEV is
actually sent via the pass(4) device anyway. But this
provides a way for the user to specify devices in a more
convenient way, and can work on device rescans when the
device is going away, assuming it still exists in the EDT.
sbin/camcontrol/camcontrol.8:
Update the man page for the rescan and reset subcommands
to reflect that you can now use a device name and unit
number with them.
Sponsored by: Spectra Logic
MFC after: 3 days
camcontrol timestamp -s would somtimes fail due to stack garbage. Zero out
the timestamp parameters to fix it.
Fix another nearby bug, and update the man page.
sbin/camcontrol/timestamp.c:
In set_timestamp(), bzero ts_p prior to creating the timestamp.
Previously stack garbage could cause some tape drives to reject the
timestamp.
In set_timestamp(), check for failures from strptime().
sbin/camcontrol/camcontrol.8:
Add the time argument to the -T option to camcontrol timestamp -s
in the long description.
Change the time/date format used in the camcontrol timestamp
example to RFC 2822 format. This fixes a time zone issue with the
original example by specifying the time zone as -0600. Otherwise,
the time zone seems to default to standard time in the current
locale, which makes the time, when reported back from the drive,
1 hour off from the intended setting. This also fixes a duplicate
day of the week ("Wednesday Wed") in the previous example.
Submitted by: Sam Klopsch
MFC after: 3 days
Sponsored by: Spectra Logic
Users can use the new generic argument, -Q task_attr, to specify a task
attribute (simple, ordered, head of queue, aca) for the commands issued.
The the default is simple, which works with all SCSI devices that support
tagged queueing.
This will mostly be useful for debugging target behavior in certain
situations.
You can try it out by compiling CTL with CTL_IO_DELAY turned on (in
sys/cam/ctl/ctl_io.h) and then do something like this with one of the CTL
LUNs:
ctladm delay 0:0 -l done -t 10
camcontrol tur da34 -v
And at then before the 10 second timer is up, in another terminal:
camcontrol inquiry da34 -Q ordered -v
The Inquiry should complete just after the TUR completes. Ordinarily
it would complete first because of the delay injection, but because the
task attribute is set to ordered in this case, CTL holds it up until the
previous command has completed.
sbin/camcontrol/camcontrol.c:
Add the new generic argument, -Q, which allows the user to specify
a SCSI task attribute. The user can specify task attributes by
name or numerically.
Add a new task_attr arguments to SCSI sub-functions.
sbin/camcontrol/attrib.c,
sbin/camcontrol/camcontrol.h,
sbin/camcontrol/fwdownload.c,
sbin/camcontrol/modeedit.c,
sbin/camcontrol/persist.c,
sbin/camcontrol/timestamp.c,
sbin/camcontrol/zone.c:
Add the new task_attr argument to SCSI sub-functions.
sbin/camcontrol/camcontrol.8:
Document the new -Q option, and add an example.
Sponsored by: Spectra Logic
MFC after: 1 week
CID 1229913 Fix output of "camcontrol persist -i report_capabilities".
The reported Persistent Reservation Types were wrong in all
cases.
CID 1356029 Annotate the code so Coverity will know that this is a false
positive.
CID 1366830 Fix a memory leak in "camcontrol timestamp -s"
CID 1366832 Fix a segfault that could be caused by bad drive firmware
Also, fix the man page entry for the "camcontrol epc state" command to match
what the code does.
Reviewed by: ken, wblock
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9239
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
Previously code ignored resid field and returned extra zeroes in case of
data underflow. Now it returns only real bytes received from target.
MFC after: 2 weeks
If our buffer is too small, we may receive part of the page, and should
not try read/write past the end of the buffer.
Reported by: Coverity
CID: 1368374, 1368375
MFC after: 1 week
This adds support to camcontrol(8) and libcam(3) for getting and setting
the time on SCSI protocol drives. This is more commonly found on tape
drives, but is a SPC (SCSI Primary Commands) command, and may be found
on any device that speaks SCSI.
The new camcontrol timestamp subcommand allows getting the current device
time or setting the time to the current system time or any arbitrary time.
sbin/camcontrol/Makefile:
Add timestamp.c.
sbin/camcontrol/camcontrol.8:
Document the new timestamp subcommand.
sbin/camcontrol/camcontrol.c:
Add the timestamp subcommand to camcontrol.
sbin/camcontrol/camcontrol.h:
Add the timestamp() function prototype.
sbin/camcontrol/timestamp.c:
Timestamp setting and reporting functionality.
sys/cam/scsi/scsi_all.c:
Add two new CCB building functions, scsi_set_timestamp() and
scsi_report_timestamp(). Also, add a new helper function,
scsi_create_timestamp().
sys/cam/scsi/scsi_all.h:
Add CDB and parameter data for the the set and report timestamp
commands.
Add function declarations for the new CCB building and helper
functions.
Submitted by: Sam Klopsch
Sponsored by: Spectra Logic
MFC After: 2 weeks
In r307684, I changed rescan_or_reset_bus() to bzero stack-allocated CCBs
before sending them to the kernel because there was stack garbage in there
that wound up meaning that bogus CCB flags were set.
While this fixed the 'camcontrol rescan all' case (XPT_DEV_MATCH CCBs were
failing previously), it broke the 'camcontrol rescan 0' (or any other
number) case when INVARIANTS are turned on. Rescanning a single bus
reliably produced an assert in cam_periph_runccb():
panic: cam_periph_runccb: ccb=0xfffff80044ffe000, func_code=0x708, flags=0xffffdde0
The flags values don't make sense from the code. Changing the CCBs in
rescan_or_reset_bus() from stack to heap allocated avoids the problem.
It would be better to understand why userland stack allocated CCBs don't
work properly, since there may be other code that breaks if stack allocated
CCBs don't work.
sbin/camcontrol/camcontrol.c:
In rescan_or_reset_bus(), allocate the CCBs using malloc(3) instead
of on the stack to avoid an assertion in cam_periph_runccb().
MFC after: 3 days
Sponsored by: Spectra Logic
the header. Otherwise stack garbage can lead to random flags getting set.
This showed up as 'camcontrol rescan all' failing with EINVAL because the
address type wasn't CAM_DATA_VADDR.
sbin/camcontrol/camcontrol.c:
In rescan_or_reset_bus(), bzero the stack-allocated CCBs before
use instead of clearing the body.
MFC after: 3 days
Sponsored by: Spectra Logic
defects. When shifting an unsigned byte into the upper 8 bits of
an int and the resulting value is greater than 0x7FFFFFF, the result
will be sign extended when converting to a 64 bit unsigned long.
Fix by casting to (uint64_t) before the shift.
Reported by: Coverity
CID: 1356044, 1356045
Reviewed by: ken
overflow defect. Use the new CCB_CLEAR_ALL_EXCEPT_HDR() macro
instead of the calling bzero() on the pointer to the header used
as an array and indexed by 1.
Don't leak a buffer after executing "goto restart_report" by
overwriting its pointer with the results of another calloc().
Be sure to clear the buffer before reusing it. (CID 1356042)
Reported by: Coverity
CID: 1356022, 1356034, 1356023, 1356035, 1356042
Reviewed by: ken
The currently used idiom for clearing the part of a ccb after its
header generates one or two Coverity errors for each time it is
used. All instances generate an Out-of-bounds access (ARRAY_VS_SINGLETON)
error because of the treatment of the header as a two element array,
with a pointer to the non-existent second element being passed as
the starting address to bzero(). Some instances also alsp generate
Out-of-bounds access (OVERRUN) errors, probably because the space
being cleared is larger than the sizeofstruct ccb_hdr).
In addition, this idiom is difficult for humans to understand and
it is error prone. The user has to chose the proper struct ccb_*
type (which does not appear in the surrounding code) for the sizeof()
in the length calculation. I found several instances where the
length was incorrect, which could cause either an actual out of
bounds write, or incompletely clear the ccb.
A better way is to write the code to clear the ccb itself starting
at sizeof(ccb_hdr) bytes from the start of the ccb, and calculate
the length based on the specific type of struct ccb_* being cleared
as specified by the union ccb member being used. The latter can
normally be seen in the nearby code. This is friendlier for Coverity
and other static analysis tools because they will see that the
intent is to clear the trailing part of the ccb.
Wrap all of the boilerplate code in a convenient macro that only
requires a pointer to the desired union ccb member (or a pointer
to the union ccb itself) as an argument.
Reported by: Coverity
CID: 1007578, 1008684, 1009724, 1009773, 1011304, 1011306
CID: 1011307, 1011308, 1011309, 1011310, 1011311, 1011312
CID: 1011313, 1011314, 1011315, 1011316, 1011317, 1011318
CID: 1011319, 1011320, 1011321, 1011322, 1011324, 1011325
CID: 1011326, 1011327, 1011328, 1011329, 1011330, 1011374
CID: 1011390, 1011391, 1011392, 1011393, 1011394, 1011395
CID: 1011396, 1011397, 1011398, 1011399, 1011400, 1011401
CID: 1011402, 1011403, 1011404, 1011405, 1011406, 1011408
CID: 1011409, 1011410, 1011411, 1011412, 1011413, 1011414
CID: 1017461, 1018387, 1086860, 1086874, 1194257, 1229897
CID: 1229968, 1306229, 1306234, 1331282, 1331283, 1331294
CID: 1331295, 1331535, 1331536, 1331539, 1331540, 1341623
CID: 1341624, 1341637, 1341638, 1355264, 1355324
Reviewed by: scottl, ken, delphij, imp
MFH: 1 month
Differential Revision: https://reviews.freebsd.org/D6496
This change includes support for SCSI SMR drives (which conform to the
Zoned Block Commands or ZBC spec) and ATA SMR drives (which conform to
the Zoned ATA Command Set or ZAC spec) behind SAS expanders.
This includes full management support through the GEOM BIO interface, and
through a new userland utility, zonectl(8), and through camcontrol(8).
This is now ready for filesystems to use to detect and manage zoned drives.
(There is no work in progress that I know of to use this for ZFS or UFS, if
anyone is interested, let me know and I may have some suggestions.)
Also, improve ATA command passthrough and dispatch support, both via ATA
and ATA passthrough over SCSI.
Also, add support to camcontrol(8) for the ATA Extended Power Conditions
feature set. You can now manage ATA device power states, and set various
idle time thresholds for a drive to enter lower power states.
Note that this change cannot be MFCed in full, because it depends on
changes to the struct bio API that break compatilibity. In order to
avoid breaking the stable API, only changes that don't touch or depend on
the struct bio changes can be merged. For example, the camcontrol(8)
changes don't depend on the new bio API, but zonectl(8) and the probe
changes to the da(4) and ada(4) drivers do depend on it.
Also note that the SMR changes have not yet been tested with an actual
SCSI ZBC device, or a SCSI to ATA translation layer (SAT) that supports
ZBC to ZAC translation. I have not yet gotten a suitable drive or SAT
layer, so any testing help would be appreciated. These changes have been
tested with Seagate Host Aware SATA drives attached to both SAS and SATA
controllers. Also, I do not have any SATA Host Managed devices, and I
suspect that it may take additional (hopefully minor) changes to support
them.
Thanks to Seagate for supplying the test hardware and answering questions.
sbin/camcontrol/Makefile:
Add epc.c and zone.c.
sbin/camcontrol/camcontrol.8:
Document the zone and epc subcommands.
sbin/camcontrol/camcontrol.c:
Add the zone and epc subcommands.
Add auxiliary register support to build_ata_cmd(). Make sure to
set the CAM_ATAIO_NEEDRESULT, CAM_ATAIO_DMA, and CAM_ATAIO_FPDMA
flags as appropriate for ATA commands.
Add a new get_ata_status() function to parse ATA result from SCSI
sense descriptors (for ATA passthrough over SCSI) and ATA I/O
requests.
sbin/camcontrol/camcontrol.h:
Update the build_ata_cmd() prototype
Add get_ata_status(), zone(), and epc().
sbin/camcontrol/epc.c:
Support for ATA Extended Power Conditions features. This includes
support for all features documented in the ACS-4 Revision 12
specification from t13.org (dated February 18, 2016).
The EPC feature set allows putting a drive into a power power mode
immediately, or setting timeouts so that the drive will
automatically enter progressively lower power states after various
idle times.
sbin/camcontrol/fwdownload.c:
Update the firmware download code for the new build_ata_cmd()
arguments.
sbin/camcontrol/zone.c:
Implement support for Shingled Magnetic Recording (SMR) drives
via SCSI Zoned Block Commands (ZBC) and ATA Zoned Device ATA
Command Set (ZAC).
These specs were developed in concert, and are functionally
identical. The primary differences are due to SCSI and ATA
differences. (SCSI is big endian, ATA is little endian, for
example.)
This includes support for all commands defined in the ZBC and
ZAC specs.
sys/cam/ata/ata_all.c:
Decode a number of additional ATA command names in ata_op_string().
Add a new CCB building function, ata_read_log().
Add ata_zac_mgmt_in() and ata_zac_mgmt_out() CCB building
functions. These support both DMA and NCQ encapsulation.
sys/cam/ata/ata_all.h:
Add prototypes for ata_read_log(), ata_zac_mgmt_out(), and
ata_zac_mgmt_in().
sys/cam/ata/ata_da.c:
Revamp the ada(4) driver to support zoned devices.
Add four new probe states to gather information needed for zone
support.
Add a new adasetflags() function to avoid duplication of large
blocks of flag setting between the async handler and register
functions.
Add new sysctl variables that describe zone support and paramters.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
sys/cam/scsi/scsi_all.c:
Add command descriptions for the ZBC IN/OUT commands.
Add descriptions for ZBC Host Managed devices.
Add a new function, scsi_ata_pass() to do ATA passthrough over
SCSI. This will eventually replace scsi_ata_pass_16() -- it
can create the 12, 16, and 32-byte variants of the ATA
PASS-THROUGH command, and supports setting all of the
registers defined as of SAT-4, Revision 5 (March 11, 2016).
Change scsi_ata_identify() to use scsi_ata_pass() instead of
scsi_ata_pass_16().
Add a new scsi_ata_read_log() function to facilitate reading
ATA logs via SCSI.
sys/cam/scsi/scsi_all.h:
Add the new ATA PASS-THROUGH(32) command CDB. Add extended and
variable CDB opcodes.
Add Zoned Block Device Characteristics VPD page.
Add ATA Return SCSI sense descriptor.
Add prototypes for scsi_ata_read_log() and scsi_ata_pass().
sys/cam/scsi/scsi_da.c:
Revamp the da(4) driver to support zoned devices.
Add five new probe states, four of which are needed for ATA
devices.
Add five new sysctl variables that describe zone support and
parameters.
The da(4) driver supports SCSI ZBC devices, as well as ATA ZAC
devices when they are attached via a SCSI to ATA Translation (SAT)
layer. Since ZBC -> ZAC translation is a new feature in the T10
SAT-4 spec, most SATA drives will be supported via ATA commands
sent via the SCSI ATA PASS-THROUGH command. The da(4) driver will
prefer the ZBC interface, if it is available, for performance
reasons, but will use the ATA PASS-THROUGH interface to the ZAC
command set if the SAT layer doesn't support translation yet.
As I mentioned above, ZBC command support is untested.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
Add scsi_zbc_in() and scsi_zbc_out() CCB building functions.
Add scsi_ata_zac_mgmt_out() and scsi_ata_zac_mgmt_in() CCB/CDB
building functions. Note that these have return values, unlike
almost all other CCB building functions in CAM. The reason is
that they can fail, depending upon the particular combination
of input parameters. The primary failure case is if the user
wants NCQ, but fails to specify additional CDB storage. NCQ
requires using the 32-byte version of the SCSI ATA PASS-THROUGH
command, and the current CAM CDB size is 16 bytes.
sys/cam/scsi/scsi_da.h:
Add ZBC IN and ZBC OUT CDBs and opcodes.
Add SCSI Report Zones data structures.
Add scsi_zbc_in(), scsi_zbc_out(), scsi_ata_zac_mgmt_out(), and
scsi_ata_zac_mgmt_in() prototypes.
sys/dev/ahci/ahci.c:
Fix SEND / RECEIVE FPDMA QUEUED in the ahci(4) driver.
ahci_setup_fis() previously set the top bits of the sector count
register in the FIS to 0 for FPDMA commands. This is okay for
read and write, because the PRIO field is in the only thing in
those bits, and we don't implement that further up the stack.
But, for SEND and RECEIVE FPDMA QUEUED, the subcommand is in that
byte, so it needs to be transmitted to the drive.
In ahci_setup_fis(), always set the the top 8 bits of the
sector count register. We need it in both the standard
and NCQ / FPDMA cases.
sys/geom/eli/g_eli.c:
Pass BIO_ZONE commands through the GELI class.
sys/geom/geom.h:
Add g_io_zonecmd() prototype.
sys/geom/geom_dev.c:
Add new DIOCZONECMD ioctl, which allows sending zone commands to
disks.
sys/geom/geom_disk.c:
Add support for BIO_ZONE commands.
sys/geom/geom_disk.h:
Add a new flag, DISKFLAG_CANZONE, that indicates that a given
GEOM disk client can handle BIO_ZONE commands.
sys/geom/geom_io.c:
Add a new function, g_io_zonecmd(), that handles execution of
BIO_ZONE commands.
Add permissions check for BIO_ZONE commands.
Add command decoding for BIO_ZONE commands.
sys/geom/geom_subr.c:
Add DDB command decoding for BIO_ZONE commands.
sys/kern/subr_devstat.c:
Record statistics for REPORT ZONES commands. Note that the
number of bytes transferred for REPORT ZONES won't quite match
what is received from the harware. This is because we're
necessarily counting bytes coming from the da(4) / ada(4) drivers,
which are using the disk_zone.h interface to communicate up
the stack. The structure sizes it uses are slightly different
than the SCSI and ATA structure sizes.
sys/sys/ata.h:
Add many bit and structure definitions for ZAC, NCQ, and EPC
command support.
sys/sys/bio.h:
Convert the bio_cmd field to a straight enumeration. This will
yield more space for additional commands in the future. After
change r297955 and other related changes, this is now possible.
Converting to an enumeration will also prevent use as a bitmask
in the future.
sys/sys/disk.h:
Define the DIOCZONECMD ioctl.
sys/sys/disk_zone.h:
Add a new API for managing zoned disks. This is very close to
the SCSI ZBC and ATA ZAC standards, but uses integers in native
byte order instead of big endian (SCSI) or little endian (ATA)
byte arrays.
This is intended to offer to the complete feature set of the ZBC
and ZAC disk management without requiring the application developer
to include SCSI or ATA headers. We also use one set of headers
for ioctl consumers and kernel bio-level consumers.
sys/sys/param.h:
Bump __FreeBSD_version for sys/bio.h command changes, and inclusion
of SMR support.
usr.sbin/Makefile:
Add the zonectl utility.
usr.sbin/diskinfo/diskinfo.c
Add disk zoning capability to the 'diskinfo -v' output.
usr.sbin/zonectl/Makefile:
Add zonectl makefile.
usr.sbin/zonectl/zonectl.8
zonectl(8) man page.
usr.sbin/zonectl/zonectl.c
The zonectl(8) utility. This allows managing SCSI or ATA zoned
disks via the disk_zone.h API. You can report zones, reset write
pointers, get parameters, etc.
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D6147
Reviewed by: wblock (documentation)
This makes it possible to manually force updating capacity data
after the disk got resized. Without it it might be neccessary to
reboot before FreeBSD notices updated disk size under eg VMWare.
Discussed with: imp@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6108
It was already done 4 lines prior and the value of error didn't change
MFC after: 3 days
Reported by: Coverity
CID: 1011236
Sponsored by: EMC / Isilon Storage Division
mode value isn't always clipped to -1 when (resolution * size) == 32, which
would have been the case with values => {4i,32b,32t}.
This seems to have been broken in r64382.
MFC after: 1 week
X-MFC with: r289915
PR: 200619
Reported by: Michael Baptist
Submitted by: Lars Skodje
Sponsored by: EMC / Isilon Storage Division
The significant changes and bugs fixed here are:
1. Fixed a bug in the progress display code:
When the user's filename is too big, or his terminal width is too
small, the progress code could wind up using a negative number for
the length of the "stars" that it uses to indicate progress.
This negative value was assigned to an unsigned variable, resulting
in a very large positive value.
The result is that we wound up writing garbage from memory to the
user's terminal.
With an 80 column terminal, a file name length of more than 35
characters would generate this problem.
To address this, we now set a minimum progress bar length, and
truncate the user's file name as needed.
This has been tested with large filenames and small terminals, and
at least produces reasonable results. If the terminal is too
narrow, the progress display takes up an additional line with each
update, but this is more user friendly than writing garbage to the
tty.
2. SATA drives connected via a SATA controller didn't have SCSI Inquiry
data populated in struct cam_device. This meant that the code in
fw_get_vendor() in fwdownload.c would try to match a zero-length
vendor ID, and so return the first entry in the vendor table. (Which
used to be HITACHI.) Fixed by grabbing identify data, passing the
identify buffer into fw_get_vendor(), and matching against the model
name.
3. SATA drives connected via a SAS controller do have Inquiry data
populated. The table included a couple of entries -- "ATA ST" and
"ATA HDS", intended to handle Seagate and Hitachi SATA drives attached
via a SAS controller. SCSI to ATA translation layers use a vendor
ID of "ATA" (which is standard), and then the model name from the ATA
identify data as the SCSI product name when they are returning data on
SATA disks. The cam_strmatch code will match the first part of the
string (because the length it is given is the length of the vendor,
"ATA"), and return 0 (i.e. a match). So all SATA drives attached to
a SAS controller would be programmed using the Seagate method
(WRITE BUFFER mode 7) of SCSI firmware downloading.
4. Issue #2 above covered up a bug in fw_download_img() -- if the
maximum packet size in the vendor table was 0, it tried to default
to a packet size of 32K. But then it didn't actually succeed in
doing that, because it set the packet size to the value that was
in the vendor table (0). Now that we actually have ATA attached
drives fall use the VENDOR_ATA case, we need a reasonable default
packet size. So this is fixed to properly set the default packet size.
5. Add support for downloading firmware to IBM LTO drives, and add a
firmware file validation method to make sure that the firmware
file matches the drive type. IBM tape drives include a Load ID and
RU name in their vendor-specific VPD page 0x3. Those should match
the IDs in the header of the firmware file to insure that the
proper firmware file is loaded.
6. This also adds a new -q option to the camcontrol fwdownload
subcommand to suppress informational output. When -q is used in
combination with -y, the firmware upgrade will happen without
prompting and without output except if an error condition occurs.
7. Re-add support for printing out SCSI inquiry information when
asking the user to confirm that they want to download firmware, and
add printing of ATA Identify data if it is a SATA disk. This was
removed in r237281 when support for flashing ATA disks was added.
8. Add a new camcontrol(8) "opcodes" subcommand, and use the
underlying code to get recommended timeout values for drive
firmware downloads.
Many SCSI devices support the REPORT SUPPORTED OPERATION CODES
command, and some support the optional timeout descriptor that
specifies nominal and recommended timeouts for the commands
supported by the device.
The new camcontrol opcodes subcommand allows displaying all
opcodes supported by a drive, information about which fields
in a SCSI CDB are actually used by a given SCSI device, and the
nominal and recommended timeout values for each command.
Since firmware downloads can take a long time in some devices, and
the time varies greatly between different types of devices, take
advantage of the infrastructure used by the camcontrol opcodes
subcommand to determine the best timeout to use for the WRITE
BUFFER command in SCSI device firmware downloads.
If the device recommends a timeout, it is likely to be more
accurate than the default 50 second timeout used by the firmware
download code. If the user specifies a timeout, it will override
the default or device recommended timeout. If the device doesn't
support timeout descriptors, we fall back to the default.
9. Instead of downloading firmware to SATA drives behind a SAS controller
using WRITE BUFFER, use the SCSI ATA PASS-THROUGH command to compose
an ATA DOWNLOAD MICROCODE command and it to the drive. The previous
version of this code attempted to send a SCSI WRITE BUFFER command to
SATA drives behind a SAS controller. Although that is part of the
SAT-3 spec, it doesn't work with the parameters used with LSI
controllers at least.
10.Add a new mechanism for making common ATA passthrough and
ATA-behind-SCSI passthrough commands.
The existing camcontrol(8) ATA command mechanism checks the device
type on every command executed. That works fine for individual
commands, but is cumbersome for things like a firmware download
that send a number of commands.
The fwdownload code detects the device type up front, and then
sends the appropriate commands.
11.In simulation mode (-s), if the user specifies the -v flag, print out
the SCSI CDB or ATA registers that would be sent to the drive. This will
aid in debugging any firmware download issues.
sbin/camcontrol/fwdownload.c:
Add a device type to the fw_vendor structure, so that we can
specify different download methods for different devices from the
same vendor. In this case, IBM hard drives (from when they
still made hard drives) and tape drives.
Add a tur_status field to the fw_vendor structure so that we can
specify whether the drive to be upgraded should be ready, not
ready, or whether it doesn't matter. Add the corresponding
capability in fw_download_img().
Add comments describing each of the vendor table fields.
Add HGST and SmrtStor to the supported SCSI vendors list.
In fw_get_vendor(), look at ATA identify data if we have a SATA
device to try to identify what the drive vendor is.
Add IBM firmware file validation. This gets VPD page 0x3, and
compares the Load ID and RU name in the page to the values
included in the header. The validation code will refuse to load
a firmware file if the values don't match. This does allow the
user to attempt a downgrade; whether or not it succeeds will
likely depend on the drive settings.
Add a -q option, and disable all informative output
(progress bars, etc.) when this is enabled.
Re-add the inquiry in the confirmation dialog so the user has
a better idea of which device he is talking to. Add support for
displaying ATA identify data.
Don't automatically disable confirmation in simulation (-s) mode.
This allows the user to see the inquiry or identify data in the
dialog, and see exactly what they would see when the command
actually runs. Also, in simulation mode, if the user specifies
the -v flag, print out the SCSI CDB or ATA registers that would
be sent to the drive. This will aid in debugging any firmware
download issues.
Add a timeout field and timeout type to the firmware download
vendor table. This allows specifying a default timeout and allows
specifying whether we should attempt to probe for a recommended
timeout from the drive.
Add a new fuction, fw_get_timeout(), that will determine
which timeout to use for the WRITE BUFFER command. If the
user specifies a timeout, we always use that. Otherwise,
we will use the drive recommended timeout, if available,
and fall back to the default when a drive recommended
timeout isn't available.
When we prompt the user, tell him what timeout we're going
to use, and the source of the timeout.
Revamp the way SATA devices are handled.
In fwdownload(), use the new get_device_type() function to
determine what kind of device we're talking to.
Allow firmware downloads to any SATA device, but restrict
SCSI downloads to known devices. (The latter is not a
change in behavior.)
Break out the "ready" check from fw_download_img() into a
new subfunction, fw_check_device_ready(). This sends the
appropriate command to the device in question -- a TEST
UNIT READY or an IDENTIFY. The IDENTIFY for SATA devices
a SAT layer is done using the SCSI ATA PASS-THROUGH
command.
Use the new build_ata_cmd() function to build either a SCSI or
ATA I/O CCB to issue the DOWNLOAD MICROCODE command to SATA
devices. build_ata_cmd() figures looks at the devtype argument
and fills in the correct CCB type and CDB or ATA registers.
Revamp the vendor table to remove the previous
vendor-specific ATA entries and use a generic ATA vendor
placeholder. We currently use the same method for all ATA
drives, although we may have to add vendor-specific
behavior once we test this with more drives.
sbin/camcontrol/progress.c:
In progress_draw(), make barlength a signed value so that
we can easily detect a negative value.
If barlength (the length of the progress bar) would wind up
negative due to a small TTY width or a large filename,
set the bar length to the new minimum (10 stars) and
truncate the user's filename. We will truncate it down to
0 characters if necessary.
Calculate a new prefix_len variable (user's filename length)
and use it as the precision when printing the filename.
sbin/camcontrol/camcontrol.c:
Implement a new camcontrol(8) subcommand, "opcodes". The
opcodes subcommand allows displaying the entire list of
SCSI commands supported by a device, or details on an
individual command. In either case, it can display
nominal and recommended timeout values.
Add the scsiopcodes() function, which calls the new
scsigetopcodes() function to fetch opcode data from a
drive.
Add two new functions, scsiprintoneopcode() and
scsiprintopcodes(), which print information about one
opcode or all opcodes, respectively.
Remove the get_disk_type() function. It is no longer used.
Add a new function, dev_has_vpd_page(), that fetches the
supported INQUIRY VPD list from a device and tells the
caller whether the requested VPD page is available.
Add a new function, get_device_type(), that returns a more
precise device type than the old get_disk_type() function.
The get_disk_type() function only distinguished between
SCSI and ATA devices, and SATA devices behind a SCSI to ATA
translation layer were considered to be "SCSI".
get_device_type() offers a third type, CC_DT_ATA_BEHIND_SCSI.
We need to know this to know whether to attempt to send ATA
passthrough commands. If the device has the ATA
Information VPD page (0x89), then it is an ATA device
behind a SCSI to ATA translation layer.
Remove the type argument from the fwdownload() subcommand.
Add a new function, build_ata_cmd(), that will take one set
of common arguments and build either a SCSI or ATA I/O CCB,
depending on the device type passed in.
sbin/camcontrol/camcontrol.h:
Add a prototype for scsigetopcodes().
Add a new enumeration, camcontrol_devtype.
Add prototypes for dev_has_vpd_page(), get_device_type()
and build_ata_cmd().
Remove the type argument from the fwdownload() subcommand.
sbin/camcontrol/camcontrol.8
Explain that the fwdownload subcommand will use the drive
recommended timeout if available, and that the user can
override the timeout.
Document the new opcodes subcommand.
Explain that we will attempt to download firmware to any
SATA device.
Document supported SCSI vendors, and models tested if known.
Explain the commands used to download firmware for the
three different drive and controller combinations.
Document that the -v flag in simulation mode for the fwdownload
subcommand will print out the SCSI CDBs or ATA registers that would
be used.
sys/cam/scsi/scsi_all.h:
Add new bit definitions for the one opcode descriptor for
the REPORT SUPPORTED OPCODES command.
Add a function prototype for scsi_report_supported_opcodes().
sys/cam/scsi/scsi_all.c:
Add a new CDB building function, scsi_report_supported_opcodes().
Sponsored by: Spectra Logic
MFC after: 1 week
Off by default, build behaves normally.
WITH_META_MODE we get auto objdir creation, the ability to
start build from anywhere in the tree.
Still need to add real targets under targets/ to build packages.
Differential Revision: D2796
Reviewed by: brooks imp
MAM is Medium Auxiliary Memory and is most commonly found as flash
chips on tapes.
This includes support for reading attributes and decoding most
known attributes, but does not yet include support for writing
attributes or reporting attributes in XML format.
libsbuf/Makefile:
Add subr_prf.c for the new sbuf_hexdump() function. This
function is essentially the same function.
libsbuf/Symbol.map:
Add a new shared library minor version, and include the
sbuf_hexdump() function.
libsbuf/Version.def:
Add version 1.4 of the libsbuf library.
libutil/hexdump.3:
Document sbuf_hexdump() alongside hexdump(3), since it is
essentially the same function.
camcontrol/Makefile:
Add attrib.c.
camcontrol/attrib.c:
Implementation of READ ATTRIBUTE support for camcontrol(8).
camcontrol/camcontrol.8:
Document the new 'camcontrol attrib' subcommand.
camcontrol/camcontrol.c:
Add the new 'camcontrol attrib' subcommand.
camcontrol/camcontrol.h:
Add a function prototype for scsiattrib().
share/man/man9/sbuf.9:
Document the existence of sbuf_hexdump() and point users to
the hexdump(3) man page for more details.
sys/cam/scsi/scsi_all.c:
Add a table of known attributes, text descriptions and
handler functions.
Add a new scsi_attrib_sbuf() function along with a number
of other related functions that help decode attributes.
scsi_attrib_ascii_sbuf() decodes ASCII format attributes.
scsi_attrib_int_sbuf() decodes binary format attributes, and
will pass them off to scsi_attrib_hexdump_sbuf() if they're
bigger than 8 bytes.
scsi_attrib_vendser_sbuf() decodes the vendor and drive
serial number attribute.
scsi_attrib_volcoh_sbuf() decodes the Volume Coherency
Information attribute that LTFS writes out.
sys/cam/scsi/scsi_all.h:
Add a number of attribute-related structure definitions and
other defines.
Add function prototypes for all of the functions added in
scsi_all.c.
sys/kern/subr_prf.c:
Add a new function, sbuf_hexdump(). This is the same as
the existing hexdump(9) function, except that it puts the
result in an sbuf.
This also changes subr_prf.c so that it can be compiled in
userland for includsion in libsbuf.
We should work to change this so that the kernel hexdump
implementation is a wrapper around sbuf_hexdump() with a
statically allocated sbuf with a drain. That will require
a drain function that goes to the kernel printf() buffer
that can take a non-NUL terminated string as input.
That is because an sbuf isn't NUL-terminated until it is
finished, and we don't want to finish it while we're still
using it.
We should also work to consolidate the userland hexdump and
kernel hexdump implemenatations, which are currently
separate. This would also mean making applications that
currently link in libutil link in libsbuf.
sys/sys/sbuf.h:
Add the prototype for sbuf_hexdump(), and add another copy
of the hexdump flag values if they aren't already defined.
Ideally the flags should be defined in one place but the
implemenation makes it difficult to do properly. (See
above.)
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
This includes a new summary mode (-s) for camcontrol defects that
quickly tells the user the most important thing: how many defects
are in the requested list. The actual location of the defects is
less important.
Modern drives frequently have more than the 8191 defects that can
be reported by the READ DEFECT DATA (10) command. If they don't
have that many grown defects, they certainly have more than 8191
defects in the primary (i.e. factory) defect list.
The READ DEFECT DATA (12) command allows for longer parameter
lists, as well as indexing into the list of defects, and so allows
reporting many more defects.
This has been tested with HGST drives and Seagate drives, but
does not fully work with Seagate drives. Once I have a Seagate
spec I may be able to determine whether it is possible to make it
work with Seagate drives.
scsi_da.h: Add a definition for the new long block defect
format.
Add bit and mask definitions for the new extended
physical sector and bytes from index defect
formats.
Add a prototype for the new scsi_read_defects() CDB
building function.
scsi_da.c: Add a new scsi_read_defects() CDB building function.
camcontrol(8) was previously composing CDBs manually.
This is long overdue.
camcontrol.c: Revamp the camcontrol defects subcommand. We now
go through multiple stages in trying to get defect
data off the drive while avoiding various drive
firmware quirks.
We start off by requesting the defect header with
the 10 byte command. If we're in summary mode (-s)
and the drive reports fewer defects than can be
represented in the 10 byte header, we're done.
Otherwise, we know that we need to issue the
12 byte command if the drive reports the maximum
number of defects.
If we're in summary mode, we're done if we get a
good response back when asking for the 12 byte header.
If the user has asked for the full list, then we
use the address descriptor index field in the 12
byte CDB to step through the list in 64K chunks.
64K is small enough to work with most any ancient
or modern SCSI controller.
Add support for printing the new long block defect
format, as well as the extended physical sector and
bytes from index formats. I don't have any drives
that support the new formats.
Add a hexadecimal output format that can be turned
on with -X.
Add a quiet mode (-q) that can be turned on with
the summary mode (-s) to just print out a number.
Revamp the error detection and recovery code for
the defects command to work with HGST drives.
Call the new scsi_read_defects() CDB building
function instead of rolling the CDB ourselves.
Pay attention to the residual from the defect list
request when printing it out, so we don't run off
the end of the list.
Use the new scsi_nv library routines to convert
from strings to numbers and back.
camcontrol.8: Document the new defect formats (longblock, extbfi,
extphys) and command line options (-q, -s, -S and
-X) for the defects subcommand.
Explain a little more about what drives generally
do and don't support.
Sponsored by: Spectra Logic
MFC after: 1 week
devq_openings counter lost its meaning after allocation queues has gone.
held counter is still meaningful, but problematic to update due to separate
locking of CCB allocation and queuing.
To fix that replace devq_openings counter with allocated counter. held is
now calculated on request as difference between number of allocated, queued
and active CCBs.
MFC after: 1 month
camcontrol(8) now supports a new 'persist' subcommand that allows users to
issue SCSI PERSISTENT RESERVE IN / OUT commands.
sbin/camcontrol/Makefile:
Add persist.c.
sbin/camcontrol/persist.c:
New persistent reservation support for camcontrol(8).
We have support for all known operation modes for PERSISTENT RESERVE
IN and PERSISTENT RESERVE OUT.
exceptions noted above.
sbin/camcontrol/camcontrol.8:
Document the new 'persist' subcommand.
In the section on the Transport ID (-I) option, explain what
Transport IDs for each protocol should look like. At some point
some of this information could probably get moved off in a
separate man page, either on Transport IDs alone or a man page
documenting the Transport ID parsing code.
Add a number of examples of persistent reservation commands.
Persistent Reservations are complex enough that the average user
probably won't be able to get the commands exactly right by just
reading the man page. These examples show a few basic and
advanced examples of how to use persistent reservations.
sbin/camcontrol/camcontrol.h:
Move the definition for camcontrol_optret here, so we can use it
for the persistent reservation code.
Add a definition for the new scsipersist() function.
sbin/camcontrol/camcontrol.c:
Add 'persist' to the list of subcommands.
Document 'persist' in the help text.
sys/cam/scsi/scsi_all.c:
Add the scsi_persistent_reserve_in() and
scsi_persistent_reserve_out() CCB building functions.
Add a new function, scsi_transportid_sbuf(). This takes a
SCSI Transport ID (documented in SPC-4), and prints it to
an sbuf(9). There are some transports (like ATA, USB, and
SSA) for which there is no transport defined. We need to
come up with a reasonable thing to do if we're presented
with a Transport ID that claims to be for one of those
protocols.
Add new routines scsi_get_nv() and scsi_nv_to_str().
These functions do a table lookup to go between a string and an
integer. There are lots of table lookups needed in the
persistent reservation code in camcontrol(8).
Add a new function, scsi_parse_transportid(), along with leaf node
functions to parse:
FC, 1394 and SAS (scsi_parse_transportid_64bit())
iSCSI (scsi_parse_transportid_iscsi())
SPI (scsi_parse_transportid_spi())
RDMA (scsi_parse_transportid_rdma())
PCIe (scsi_parse_transportid_sop())
Transport IDs. Given a string with the general form proto,id these
functions create a SCSI Transport ID structure.
sys/cam/scsi/scsi_all.h:
Update the various persistent reservation data structures to
SPC4r36l, but also rename some fields that were previously
obsolete with the proper names from older SCSI specs. This
allows using older, obsolete persistent reservation types when
desired.
Add function prototypes for the new persistent reservation CCB
building functions.
Add a data strucure for the READ FULL STATUS service action
of the PERSISTENT RESERVE IN command.
Add Transport ID structures for all protocols described in SPC-4.
Add a new series of SCSI_PROTO_XXX definitions, and
redefine other defines in terms of these new definitions.
Add a prototype for scsi_transportid_sbuf().
Change a couple of "obsolete" persistent reservation data
structure fields into something more meaningful, based on
what the field was called when it was defined in the spec.
(e.g. SPC, SPC-2, etc.)
Create a new define, SPRI_MAX_LEN, for the maximum allocation
length allowed for the PERSISTENT RESERVE IN command.
Add data structures and enumerations for the new name/value
translation functions.
Add data structures for SCSI over PCIe Routing IDs.
Bring the PERSISTENT RESERVE OUT Register and Move parameter list
structure (struct scsi_per_res_out_parms) up to date with SPC-4.
Add a data structure for the transport IDs that can optionally be
appended to the basic PERSISTENT RESERVE OUT parameter list.
Move SCSI protocol macro definitions out of the VPD page 0x83
definition and combine them with the more up to date protocol
definitions higher in the file.
Add function prototypes for scsi_nv_to_str(), scsi_get_nv(),
scsi_parse_transportid_64bit(), scsi_parse_transportid_spi(),
scsi_parse_transportid_rdma(), scsi_parse_transportid_iscsi(),
scsi_parse_transportid_sop(), and scsi_parse_transportid().
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
If an expander returns 0x00 (no device attached) in the ATTACHED DEVICE
field of the SMP DISCOVER response, ignore the value of ATTACHED SAS
ADDRESS, because it is invalid. Some expanders zero out the address
when the attached device is removed, but others do not. Section
9.4.3.10 of the SAS Protocol Layer 2 revision 04b does not require them
to do so.
Approved by: ken (mentor)
MFC after: 3 weeks
