iterate lock.
This causes LORs and deadlocks as some code paths will have the com lock
held when calling ieee80211_iterate_nodes().
Here, the comlock isn't held during the node table and node iteration
locks; and the callback isn't called with any (extra) lock held.
PR: kern/170098
Submitted by: moonlightakkiy@yahoo.ca
MFC after: 4 weeks
Currently, a channel width change updates the 802.11n HT info data in
net80211 but it doesn't trigger any device changes. So the device
driver may decide that HT40 frames can be transmitted but the last
device channel set only had HT20 set.
Now, a task is scheduled so a hardware reset or change isn't done
during any active ongoing RX. It also means that it's serialised
with the other task operations (eg channel change.)
This isn't the final incantation of this work, see below.
For now, any unmodified drivers will simply receive a channel
change log entry. A subsequent patch to ath(4) will introduce
some basic channel change handling (by resetting the NIC.)
Other NICs may need to update their rate control information.
TODO:
* There's still a small window at the present moment where the
channel width has been updated but the task hasn't been fired.
The final version of this should likely pass in a channel width
field to the driver and let the driver atomically do whatever
it needs to before changing the channel.
PR: kern/166286
This introduces struct ieee80211_rx_stats - which stores the various kinds
of RX statistics which a MIMO and non-MIMO 802.11 device can export.
It also fleshes out the mimo export to userland (node_getmimoinfo()).
It assumes that MIMO radios (for now) export both ctl and ext channels.
Non-11n MIMO radios are possible (and I believe Atheros made at least
one), so if that chipset support is added, extra flags to the
struct ieee80211_rx_stats can be added to extend this support.
Two new input functions have been added - ieee80211_input_mimo() and
ieee80211_input_mimo_all() - which MIMO-aware devices can call with
MIMO specific statistics.
802.11 devices calling the non-MIMO input functions will still function.
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
long-term work before they can be serviced. Packets are tagged and
assigned an age (in seconds) at the point they are added to the
queue. If a packet is not retrieved before it's age expires it is
reclaimed. Tagging can take two forms: a reference to an ieee80211_node
(as happens in the tx path) or an opaque token in cases where there
is no reference or the node structure is not stable (i.e. it's going
to be destroyed).
o add ic_stageq to replace the per-node wds staging queue used for
dynamic wds
o add ieee80211_mac_hash for building ageq tokens; this computes a
32-bit hash from an 802.11 mac address (copied from the bridge)
o while here fix a stray ';' noticed in IEEE80211_PSQ_INIT
Reviewed by: rpaulo
Approved by: re (kensmith)
we receive the AssocResp, so we can only set ni_txparms properly
at that point. To make this possible make node_setuptxparms public
as ieee80211_node_setuptxparms.
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
identify a station operating in turbo-boost mode because it has a
pure ofdm rate set; add an explicit check for the channel type
instead of depending on IEEE80211_NODE_ERP being set
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
and xmit parameters. This makes it possible to use tdma on fractional
channels.
o add IEEE80211_MODE_HALF and IEEE80211_MODE_QUARTER; note these are
band-agnostic (may need revisiting)
o setup all default rates in ic_sup_rates instead of doing it only
for active modes; we need these to calculate the default tx parameters
which are not recalculated after a regulatory update (can't just
recalculate after installing a new channel list because we might
clobber user settings)
o remove special case code in ieee80211_get_suprates; this is now
a candidate for an inline or removal
o add various entries for new modes (roaming+tx params, wme, rate
mapping, scan set setup, country ie construction, tdma, basic rates)
Note these modes are intentionally not visible through if_media.
references to iv_bss and the sta table; this is equivalent and causes
direct reclaim of the old bss node when any references in packets inflight
are reclaimed (previously the old node would sit in the bss table until
the inactivity processing reclaimed it)
o remove ieee80211_node_reclaim now that it's only use is gone
Reviewed by: avatar, cbzimmer
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
(e.g. ath): we must check the key index and not whether the key
points at a cipher other than "undef". This looks like it's been
broken for a while. Might be worth adding an explicit clear cipher
at some point though this would require changes to the usage of
IEEE80211_KEY_UNDEFINED.
PR: 125906
indicates if an association id is required before outbound traffic
is permitted. This cleans up the previous change that broke mcast
traffic "to the stack" in ap mode as a side effect.
Reviewed by: sephe, thompsa, weongyo
don't duplicate this. These are setup according to the role of the
node--the bss node for ap and adhoc modes need to use parameters
that are the least common denomimator of all nodes in the bss;
otherwise we are setting up params for a station joining a bss and
we select those according to the capabilities of the station.
This stuff needs more work as we do extra work due to having setup
in common code paths shared by nodes using both roles.
