Depending on device capabilities use different methods to implement it.
Currently used method can be read/set via kern.cam.da.X.delete_method
sysctls. Possible values are:
NONE - no provisioning support reported by the device;
DISABLE - provisioning support was disabled because of errors;
ZERO - use WRITE SAME (10) command to write zeroes;
WS10 - use WRITE SAME (10) command with UNMAP bit set;
WS16 - use WRITE SAME (16) command with UNMAP bit set;
UNMAP - use UNMAP command (equivalent of the ATA DSM TRIM command).
The last two methods (UNMAP and WS16) are defined by SBC specification and
the UNMAP method is the most advanced one. The rest of methods I've found
supported in Linux, and as soon as they were trivial to implement, then
why not? Hope they will be useful in some cases.
Unluckily I have no devices properly reporting parameters of the logical
block provisioning support via respective VPD pages (0xB0 and 0xB2). So
all info I have/use now is the flag telling whether logical block
provisioning is supported or not. As result, specific methods chosen now
by trying different ones in order (UNMAP, WS16, DISABLE) and checking
completion status to fallback if needed. I don't expect problems from this,
as if something go wrong, it should just disable itself. It may disable
even too aggressively if only some command parameter misfit.
Unlike Linux, which executes each delete with separate request, I've
implemented here the same request aggregation as implemented in ada driver.
Tests on SSDs I have show much better results doing it this way: above
8GB/s of the linear delete on Intel SATA SSD on LSI SAS HBA (mps).
Reviewed by: silence on scsi@
MFC after: 2 month
Sponsored by: iXsystems, Inc.
in the CAM XPT bus traversal code, and a number of other periph level
issues.
cam_periph.h,
cam_periph.c: Modify cam_periph_acquire() to test the CAM_PERIPH_INVALID
flag prior to allowing a reference count to be gained
on a peripheral. Callers of this function will receive
CAM_REQ_CMP_ERR status in the situation of attempting to
reference an invalidated periph. This guarantees that
a peripheral scheduled for a deferred free will not
be accessed during its wait for destruction.
Panic during attempts to drop a reference count on
a peripheral that already has a zero reference count.
In cam_periph_list(), use a local sbuf with SBUF_FIXEDLEN
set so that mallocs do not occur while the xpt topology
lock is held, regardless of the allocation policy of the
passed in sbuf.
Add a new routine, cam_periph_release_locked_buses(),
that can be called when the caller already holds
the CAM topology lock.
Add some extra debugging for duplicate peripheral
allocations in cam_periph_alloc().
Treat CAM_DEV_NOT_THERE much the same as a selection
timeout (AC_LOST_DEVICE is emitted), but forgo retries.
cam_xpt.c: Revamp the way the EDT traversal code does locking
and reference counting. This was broken, since it
assumed that the EDT would not change during
traversal, but that assumption is no longer valid.
So, to prevent devices from going away while we
traverse the EDT, make sure we properly lock
everything and hold references on devices that
we are using.
The two peripheral driver traversal routines should
be examined. xptpdperiphtraverse() holds the
topology lock for the entire time it runs.
xptperiphtraverse() is now locked properly, but
only holds the topology lock while it is traversing
the list, and not while the traversal function is
running.
The bus locking code in xptbustraverse() should
also be revisited at a later time, since it is
complex and should probably be simplified.
scsi_da.c: Pay attention to the return value from cam_periph_acquire().
Return 0 always from daclose() even if the disk is now gone.
Add some rudimentary error injection support.
scsi_sg.c: Fix reference counting in the sg(4) driver.
The sg driver was calling cam_periph_release() on close,
but never called cam_periph_acquire() (which increments
the reference count) on open.
The periph code correctly complained that the sg(4)
driver was trying to decrement the refcount when it
was already 0.
Sponsored by: Spectra Logic
MFC after: 2 weeks
CTL is a disk and processor device emulation subsystem originally written
for Copan Systems under Linux starting in 2003. It has been shipping in
Copan (now SGI) products since 2005.
It was ported to FreeBSD in 2008, and thanks to an agreement between SGI
(who acquired Copan's assets in 2010) and Spectra Logic in 2010, CTL is
available under a BSD-style license. The intent behind the agreement was
that Spectra would work to get CTL into the FreeBSD tree.
Some CTL features:
- Disk and processor device emulation.
- Tagged queueing
- SCSI task attribute support (ordered, head of queue, simple tags)
- SCSI implicit command ordering support. (e.g. if a read follows a mode
select, the read will be blocked until the mode select completes.)
- Full task management support (abort, LUN reset, target reset, etc.)
- Support for multiple ports
- Support for multiple simultaneous initiators
- Support for multiple simultaneous backing stores
- Persistent reservation support
- Mode sense/select support
- Error injection support
- High Availability support (1)
- All I/O handled in-kernel, no userland context switch overhead.
(1) HA Support is just an API stub, and needs much more to be fully
functional.
ctl.c: The core of CTL. Command handlers and processing,
character driver, and HA support are here.
ctl.h: Basic function declarations and data structures.
ctl_backend.c,
ctl_backend.h: The basic CTL backend API.
ctl_backend_block.c,
ctl_backend_block.h: The block and file backend. This allows for using
a disk or a file as the backing store for a LUN.
Multiple threads are started to do I/O to the
backing device, primarily because the VFS API
requires that to get any concurrency.
ctl_backend_ramdisk.c: A "fake" ramdisk backend. It only allocates a
small amount of memory to act as a source and sink
for reads and writes from an initiator. Therefore
it cannot be used for any real data, but it can be
used to test for throughput. It can also be used
to test initiators' support for extremely large LUNs.
ctl_cmd_table.c: This is a table with all 256 possible SCSI opcodes,
and command handler functions defined for supported
opcodes.
ctl_debug.h: Debugging support.
ctl_error.c,
ctl_error.h: CTL-specific wrappers around the CAM sense building
functions.
ctl_frontend.c,
ctl_frontend.h: These files define the basic CTL frontend port API.
ctl_frontend_cam_sim.c: This is a CTL frontend port that is also a CAM SIM.
This frontend allows for using CTL without any
target-capable hardware. So any LUNs you create in
CTL are visible in CAM via this port.
ctl_frontend_internal.c,
ctl_frontend_internal.h:
This is a frontend port written for Copan to do
some system-specific tasks that required sending
commands into CTL from inside the kernel. This
isn't entirely relevant to FreeBSD in general,
but can perhaps be repurposed.
ctl_ha.h: This is a stubbed-out High Availability API. Much
more is needed for full HA support. See the
comments in the header and the description of what
is needed in the README.ctl.txt file for more
details.
ctl_io.h: This defines most of the core CTL I/O structures.
union ctl_io is conceptually very similar to CAM's
union ccb.
ctl_ioctl.h: This defines all ioctls available through the CTL
character device, and the data structures needed
for those ioctls.
ctl_mem_pool.c,
ctl_mem_pool.h: Generic memory pool implementation used by the
internal frontend.
ctl_private.h: Private data structres (e.g. CTL softc) and
function prototypes. This also includes the SCSI
vendor and product names used by CTL.
ctl_scsi_all.c,
ctl_scsi_all.h: CTL wrappers around CAM sense printing functions.
ctl_ser_table.c: Command serialization table. This defines what
happens when one type of command is followed by
another type of command.
ctl_util.c,
ctl_util.h: CTL utility functions, primarily designed to be
used from userland. See ctladm for the primary
consumer of these functions. These include CDB
building functions.
scsi_ctl.c: CAM target peripheral driver and CTL frontend port.
This is the path into CTL for commands from
target-capable hardware/SIMs.
README.ctl.txt: CTL code features, roadmap, to-do list.
usr.sbin/Makefile: Add ctladm.
ctladm/Makefile,
ctladm/ctladm.8,
ctladm/ctladm.c,
ctladm/ctladm.h,
ctladm/util.c: ctladm(8) is the CTL management utility.
It fills a role similar to camcontrol(8).
It allow configuring LUNs, issuing commands,
injecting errors and various other control
functions.
usr.bin/Makefile: Add ctlstat.
ctlstat/Makefile
ctlstat/ctlstat.8,
ctlstat/ctlstat.c: ctlstat(8) fills a role similar to iostat(8).
It reports I/O statistics for CTL.
sys/conf/files: Add CTL files.
sys/conf/NOTES: Add device ctl.
sys/cam/scsi_all.h: To conform to more recent specs, the inquiry CDB
length field is now 2 bytes long.
Add several mode page definitions for CTL.
sys/cam/scsi_all.c: Handle the new 2 byte inquiry length.
sys/dev/ciss/ciss.c,
sys/dev/ata/atapi-cam.c,
sys/cam/scsi/scsi_targ_bh.c,
scsi_target/scsi_cmds.c,
mlxcontrol/interface.c: Update for 2 byte inquiry length field.
scsi_da.h: Add versions of the format and rigid disk pages
that are in a more reasonable format for CTL.
amd64/conf/GENERIC,
i386/conf/GENERIC,
ia64/conf/GENERIC,
sparc64/conf/GENERIC: Add device ctl.
i386/conf/PAE: The CTL frontend SIM at least does not compile
cleanly on PAE.
Sponsored by: Copan Systems, SGI and Spectra Logic
MFC after: 1 month
sector size same as acd driver does. Together with r228808 and r228847 this
allows existing multimedia/vlc to play Audio CDs via CAM cd driver.
PR: ports/162190
MFC after: 1 week
cam_periph_runccb() since the beginning checks it and releases device queue.
After r203108 it even clears CAM_DEV_QFRZN flag after that to avoid double
release, so removed code is unreachable now.
MFC after: 1 month
As soon as not all devices support READ CAPACITY(16), automatically fall
back to READ CAPACITY(10) if CAM_REQ_INVALID or SSD_KEY_ILLEGAL_REQUEST
status returned.
It also provides first bits of information about Logical Block Provisioning
(aka UNMAP/TRIM) support by the device.
connected via SAS or USB. Unluckily I've found that SAS (mps) and USB-SATA
I have translate models in different ways, requiring twice more quirks.
Unluckily for Hitachi, their model names are trimmed on SAS, making
impossible to identify 4K sector drives that way.
GEOM and using READ CD command for reading data, same as acd driver does.
Audio CDs identified by checking respective bit of the control field of
the first track in TOC.
This fixes bunch of error messages during boot (GEOM taste) with Audio CD
inserted and allows to grab Audio CD image using just dd.
MFC after: 1 month
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
CAM.
Desriptor sense is a new sense data format that originated in SPC-3. Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.
This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.
This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.
camcontrol.c: Change uses of scsi_extract_sense() to use
scsi_extract_sense_len().
Use scsi_get_sks() instead of accessing sense key specific
data directly.
scsi_modes: Update the control mode page to the latest version (SPC-4).
scsi_cmds.c,
scsi_target.c: Change references to struct scsi_sense_data to struct
scsi_sense_data_fixed. This should be changed to allow the
user to specify fixed or descriptor sense, and then use
scsi_set_sense_data() to build the sense data.
ps3cdrom.c: Use scsi_set_sense_data() instead of setting sense data
manually.
cam_periph.c: Use scsi_extract_sense_len() instead of using
scsi_extract_sense() or accessing sense data directly.
cam_ccb.h: Bump the CAM_VERSION from 0x15 to 0x16. The change of
struct scsi_sense_data from 32 to 252 bytes changes the
size of struct ccb_scsiio, but not the size of union ccb.
So the version must be bumped to prevent structure
mis-matches.
scsi_all.h: Lots of updated SCSI sense data and other structures.
Add function prototypes for the new sense data functions.
Take out the inline implementation of scsi_extract_sense().
It is now too large to put in a header file.
Add macros to calculate whether fields are present and
filled in fixed and descriptor sense data
scsi_all.c: In scsi_op_desc(), allow the user to pass in NULL inquiry
data, and we'll assume a direct access device in that case.
Changed the SCSI RESERVED sense key name and description
to COMPLETED, as it is now defined in the spec.
Change the error recovery action for a number of read errors
to prevent lots of retries when the drive has said that the
block isn't accessible. This speeds up reconstruction of
the block by any RAID software running on top of the drive
(e.g. ZFS).
In scsi_sense_desc(), allow for invalid sense key numbers.
This allows calling this routine without checking the input
values first.
Change scsi_error_action() to use scsi_extract_sense_len(),
and handle things when invalid asc/ascq values are
encountered.
Add a new routine, scsi_desc_iterate(), that will call the
supplied function for every descriptor in descriptor format
sense data.
Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
which build descriptor and fixed format sense data. They
currently default to fixed format sense data.
Add a number of scsi_get_*() functions, which get different
types of sense data fields from either fixed or descriptor
format sense data, if the data is present.
Add a number of scsi_*_sbuf() functions, which print
formatted versions of various sense data fields. These
functions work for either fixed or descriptor sense.
Add a number of scsi_sense_*_sbuf() functions, which have a
standard calling interface and print the indicated field.
These functions take descriptors only.
Add scsi_sense_desc_sbuf(), which will print a formatted
version of the given sense descriptor.
Pull out a majority of the scsi_sense_sbuf() function and
put it into scsi_sense_only_sbuf(). This allows callers
that don't use struct ccb_scsiio to easily utilize the
printing routines. Revamp that function to handle
descriptor sense and use the new sense fetching and
printing routines.
Move scsi_extract_sense() into scsi_all.c, and implement it
in terms of the new function, scsi_extract_sense_len().
The _len() version takes a length (which should be the
sense length - residual) and can indicate which fields are
present and valid in the sense data.
Add a couple of new scsi_get_*() routines to get the sense
key, asc, and ascq only.
mly.c: Rename struct scsi_sense_data to struct
scsi_sense_data_fixed.
sbp_targ.c: Use the new sense fetching routines to get sense data
instead of accessing it directly.
sbp.c: Change the firewire/SCSI sense data transformation code to
use struct scsi_sense_data_fixed instead of struct
scsi_sense_data. This should be changed later to use
scsi_set_sense_data().
ciss.c: Calculate the sense residual properly. Use
scsi_get_sense_key() to fetch the sense key.
mps_sas.c,
mpt_cam.c: Set the sense residual properly.
iir.c: Use scsi_set_sense_data() instead of building sense data by
hand.
iscsi_subr.c: Use scsi_extract_sense_len() instead of grabbing sense data
directly.
umass.c: Use scsi_set_sense_data() to build sense data.
Grab the sense key using scsi_get_sense_key().
Calculate the sense residual properly.
isp_freebsd.h: Use scsi_get_*() routines to grab asc, ascq, and sense key
values.
Calculate and set the sense residual.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
In cdregister(), hold the periph lock semaphore during changer
probe/configuration. This removes a window where an open of the
cd device may succeed before probe processing has completed.
DEVFS, and make it accessible via the diskinfo utility.
Extend GEOM's generic attribute query mechanism into generic disk consumers.
sys/geom/geom_disk.c:
sys/geom/geom_disk.h:
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Allow disk providers to implement a new method which can override
the default BIO_GETATTR response, d_getattr(struct bio *). This
function returns -1 if not handled, otherwise it returns 0 or an
errno to be passed to g_io_deliver().
sys/cam/scsi/scsi_da.c:
sys/cam/ata/ata_da.c:
- Don't copy the serial number to dp->d_ident anymore, as the CAM XPT
is now responsible for returning this information via
d_getattr()->(a)dagetattr()->xpt_getatr().
sys/geom/geom_dev.c:
- Implement a new ioctl, DIOCGPHYSPATH, which returns the GEOM
attribute "GEOM::physpath", if possible. If the attribute request
returns a zero-length string, ENOENT is returned.
usr.sbin/diskinfo/diskinfo.c:
- If the DIOCGPHYSPATH ioctl is successful, report physical path
data when diskinfo is executed with the '-v' option.
Submitted by: will
Reviewed by: gibbs
Sponsored by: Spectra Logic Corporation
Add generic attribute change notification support to GEOM.
sys/sys/geom/geom.h:
Add a new attrchanged method field to both g_class
and g_geom.
sys/sys/geom/geom.h:
sys/geom/geom_event.c:
- Provide the g_attr_changed() function that providers
can use to advertise attribute changes.
- Perform delivery of attribute change notifications
from a thread context via the standard GEOM event
mechanism.
sys/geom/geom_subr.c:
Inherit the attrchanged method from class to geom (class instance).
sys/geom/geom_disk.c:
Provide disk_attr_changed() to provide g_attr_changed() access
to consumers of the disk API.
sys/cam/scsi/scsi_pass.c:
sys/cam/scsi/scsi_da.c:
sys/geom/geom_dev.c:
sys/geom/geom_disk.c:
Use attribute changed events to track updates to physical path
information.
sys/cam/scsi/scsi_da.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, and
the updated buffer type references our physical path
attribute, emit a GEOM attribute changed event via the
disk_attr_changed() API.
sys/cam/scsi/scsi_pass.c:
Add AC_ADVINFO_CHANGED to the registered asynchronous CAM
events for this driver. When this event occurs, update
the physical patch devfs alias for this pass instance.
Submitted by: gibbs
Sponsored by: Spectra Logic Corporation
- Only attempt the closing synchronize cache on a disk
if it is still there.
- When a device is lost, report the number of outstanding
I/Os as they are drained.
- When a device is lost, return any unprocessed bios with
ENXIO instead of EIO.
- Filter asynchronous events, but always allow cam_periph_async()
to see them too.
Sponsored by: Spectra Logic Corporation
other device attributes stored in the CAM Existing Device Table (EDT).
This includes some infrastructure requried by the enclosure services
driver to export physical path information.
Make the CAM device advanced info interface accept store requests.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
- Replace scsi_get_sas_addr() with a scsi_get_devid() which takes
a callback that decides whether to accept a particular descriptor.
Provide callbacks for NAA IEEE Registered addresses and for SAS
addresses, replacing the old function. This is needed because
the old function doesn't work for an enclosure address for a SAS
device, which is not flagged as a SAS address, but is NAA IEEE
Registered. It may be worthwhile merging this interface with the
devid match interface.
- Add a few more defines for some device ID fields.
sbin/camcontrol/camcontrol.c:
- Update for the CCB_DEV_ADVINFO interface change.
cam/cam_xpt_internal.h:
- Add the new fields for the physical path string to the CAM EDT.
cam/cam_ccb.h:
- Rename CCB_GDEV_ADVINFO to simply CCB_DEV_ADVINFO, and the ccb
structure to ccb_dev_advinfo.
- Add a flag that changes this CCB's action to store, rather than
the default, retrieve.
- Add a new buffer type, CDAI_TYPE_PHYS_PATH, for the new CAM EDT
physpath field.
- Remove the never-implemented transport & proto flags.
cam/cam_xpt.c:
cam/cam_xpt.h:
- Add xpt_getattr(), which provides a wrapper for fetching a device's
attribute using the GEOM strings as key. This method currently
supports "GEOM::ident" and "GEOM::physpath".
Submitted by: will
Reviewed by : gibbs
Extend the XPT_DEV_MATCH api to allow a device search by device ID.
As far as the API is concerned, device ID is a binary blob to be
interpreted by the transport layer. The SCSI implementation assumes
it is an array of VPD device ID descriptors.
sys/cam/cam_ccb.h:
Create a new structure, device_id_match_pattern, and
update the XPT_DEV_MATCH datastructures and flags so
that this pattern type can be used.
sys/cam/cam_xpt.c:
- A single pattern matching on both inquiry data and device
ID is invalid. Report any violators.
- Pass device ID match requests through to the new routine
scsi_devid_match(). The direct call of a SCSI routine is
a layering violation, but no worse than the one a few
lines up that checks inquiry data. Defer cleaning this
up until our future, larger, rototilling of CAM.
- Zero out cam_ed and cam_et nodes on allocation. Prior to
this change, device_id_len and device_id were not inialized,
preventing proper detection of the presence of this
information.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
Add the scsi_match_devid() routine.
Add a helper function for extracting peripherial driver names
sys/cam/cam_periph.c:
sys/cam/cam_periph.h:
Add the cam_periph_list() method which fills an sbuf
with a comma delimited list of the peripheral instances
associated with a given CAM path.
Add a helper functions for SCSI commands used by the SES driver.
sys/cam/scsi/scsi_all.c:
sys/cam/scsi/scsi_all.h:
Add structure definitions and csio filling functions for
the receive diagnostic results and send diagnostic commands.
Misc CAM XPT cleanups.
sys/cam/cam_xpt.c:
Broadcast AC_FOUND_DEVICE and AC_PATH_REGISTERED
events at the time async event handlers are attached
even when registering just for events on a partitular
SIM. Previously, you had to register for these
events on all SIMs in the system in order to get
the initial broadcast even though subsequent device
and path arrivals would be delivered.
sys/cam/cam_xpt.c:
Remove SIM mutex held asserts from path accessors.
CAM paths are reference counted and it is this
reference count, not the sim mutex, that garantees
they are stable.
Sponsored by: Spectra Logic Corporation
An optical disk may not have a TOC (e.g. for blank media) and userland
software may legitimately try to use CDIOREADTOCHEADER to find out about
the TOC.
Silence from: scsi@
MFC after: 10 days
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
camcontrol.c: In buildbusdevlist(), don't attempt to get call
getdevid() for an unconfigured device, even when the
verbose flag is set. The cam_open_btl() call will almost
certainly fail.
Probe for the buffer size when issuing the XPT_GDEV_ADVINFO
CCB. Probing for the buffer size first helps us avoid
allocating the maximum buffer size when it really may not
be necessary. This also helps avoid errors from
cam_periph_mapmem() if we attempt to map more than MAXPHYS.
cam_periph.c: In cam_periph_mapmem(), if the XPT_GDEV_ADVINFO CCB
shows a bufsiz of 0, we don't have anything to map,
so just return.
Also, set the maximum mapping size to MAXPHYS
instead of DFLTPHYS for XPT_GDEV_ADVINFO CCBs,
since they don't actually go down to the hardware.
scsi_pass.c: Don't bother mapping the buffer in XPT_GDEV_ADVINFO
CCBs if bufsiz is 0.
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
Add the BIO_ORDERED flag for struct bio and update bio clients to use it.
The barrier semantics of bioq_insert_tail() were broken in two ways:
o In bioq_disksort(), an added bio could be inserted at the head of
the queue, even when a barrier was present, if the sort key for
the new entry was less than that of the last queued barrier bio.
o The last_offset used to generate the sort key for newly queued bios
did not stay at the position of the barrier until either the
barrier was de-queued, or a new barrier (which updates last_offset)
was queued. When a barrier is in effect, we know that the disk
will pass through the barrier position just before the
"blocked bios" are released, so using the barrier's offset for
last_offset is the optimal choice.
sys/geom/sched/subr_disk.c:
sys/kern/subr_disk.c:
o Update last_offset in bioq_insert_tail().
o Only update last_offset in bioq_remove() if the removed bio is
at the head of the queue (typically due to a call via
bioq_takefirst()) and no barrier is active.
o In bioq_disksort(), if we have a barrier (insert_point is non-NULL),
set prev to the barrier and cur to it's next element. Now that
last_offset is kept at the barrier position, this change isn't
strictly necessary, but since we have to take a decision branch
anyway, it does avoid one, no-op, loop iteration in the while
loop that immediately follows.
o In bioq_disksort(), bypass the normal sort for bios with the
BIO_ORDERED attribute and instead insert them into the queue
with bioq_insert_tail(). bioq_insert_tail() not only gives
the desired command order during insertion, but also provides
barrier semantics so that commands disksorted in the future
cannot pass the just enqueued transaction.
sys/sys/bio.h:
Add BIO_ORDERED as bit 4 of the bio_flags field in struct bio.
sys/cam/ata/ata_da.c:
sys/cam/scsi/scsi_da.c
Use an ordered command for SCSI/ATA-NCQ commands issued in
response to bios with the BIO_ORDERED flag set.
sys/cam/scsi/scsi_da.c
Use an ordered tag when issuing a synchronize cache command.
Wrap some lines to 80 columns.
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/vdev_geom.c
sys/geom/geom_io.c
Mark bios with the BIO_FLUSH command as BIO_ORDERED.
Sponsored by: Spectra Logic Corporation
MFC after: 1 month
This makes things easier for target implementations to calculate how many
elements they need to allocate.
Discussed with: mjacob, gibbs
MFC after: 1 week
the case of immediate unconfigure after configure. Hold the periph an
extra count while we have the task to create sysctl context outstanding
so that the periph doesn't go away unexpectedly.
Sponsored by: Panasas
Reviewed by: scsi@
MFC after: 1 month
better devices. This can be disabled on a per-device basis using quirks as
well.
This also handles the case where there is actually no connected LUN 0
(which can definitely be the case for storage arrays).
Reviewed by: scsi@
MFC after: 1 month
for REPORT and SET TARGET PORT GROUP commands (foundations for future work).
Regularize opcodes to be upper case hex.
Pick *one* of tab or space after #define (tab) and stick with that.
MFC after: 2 weeks
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
d_mediasize
CD_FLAG_VALID_TOC is not required for setting those media properties.
PR: kern/145385
Submitted by: Juergen Lock <nox@jelal.kn-bremen.de>
a slightly different version
Tested by: Pavel Sukhoy <sukhoy@ripn.net>,
Markus Wild <m.wild@cybernet.ch>,
Juergen Lock <nox@jelal.kn-bremen.de>,
uqs
MFC after: 1 week
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
- Move tagged queueing control from ADA to ATA XPT. It allows to control
device command queue length correctly. First step to support < 32 tags.
- Limit queue for non-tagged devices by 2 slots for ahci(4) and siis(4).
- Implement quirk matching for ATA devices.
- Move xpt_schedule_dev_sendq() from header to source file.
- Move delayed queue shrinking to the more expected place - element freeing.
- Remove some SCSIsms in ATA.
- Remove CAM_PERIPH_POLLED flag. It is broken by design. Polling can't be
periph flag. May be SIM, may be CCB, but now it works fine just without it.
- Remove check unused for at least five years. If we will ever have non-BIO
devices in CAM, this check is smallest of what we will need.
- If several controllers complete requests same time, call swi_sched()
only once.
disk is first probed. dagetcapacity is called whenever the disk is opened from
geom via d_open(), a zero sector size will cause geom to panic later on.
Fix reference counting bug, when device unreferenced before then
invalidated. To do it, do not handle validity flag as another
reference, but explicitly modify reference count each time flag is
modified.
Discovered by: thompsa
- Reduce code duplication in ATA XPT and PMP driver.
- Move PIO size setting from ada driver to ATA XPT. It is XPT business
to negotiate transfer details. ada driver is now stateless.
- Report PIO size to SIM. It is required for correct PATA SIM operation.
- Tune PMP scan timings. It workarounds some problems with SiI.
- If reset hapens during PMP initialization - restart it.
- Introduce early-initialized periph drivers, which are used during initial
scan process. Use it for xpt, probe, aprobe and pmp. It gives pmp chance
to finish scan before mountroot and numerate devices in right order.
allocations M_NOWAIT so that we don't try and sleep with a nested non-sleepable
lock.
This makes the userland scsi_target begin to function again.
Obtained from: Sean Bruno
MFC after: 1 month
page_list using the matching malloc type for the allocation.
Approved by: re
Reviewed by: scottl [1]
MFC after: 1 week
[1] Original patch was against xpt_cam.c, prior to the cam refactoring.
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
vnode interlock to protect the knote fields [1]. The locking assumes
that shared vnode lock is held, thus we get exclusive access to knote
either by exclusive vnode lock protection, or by shared vnode lock +
vnode interlock.
Do not use kl_locked() method to assert either lock ownership or the
fact that curthread does not own the lock. For shared locks, ownership
is not recorded, e.g. VOP_ISLOCKED can return LK_SHARED for the shared
lock not owned by curthread, causing false positives in kqueue subsystem
assertions about knlist lock.
Remove kl_locked method from knlist lock vector, and add two separate
assertion methods kl_assert_locked and kl_assert_unlocked, that are
supposed to use proper asserts. Change knlist_init accordingly.
Add convenience function knlist_init_mtx to reduce number of arguments
for typical knlist initialization.
Submitted by: jhb [1]
Noted by: jhb [2]
Reviewed by: jhb
Tested by: rnoland
The device index number stored in the unit number of sa(4) devices is
only used to print debug messages. Get rid of this index number and use
devtoname() to just print the entire device name.
things around so the periph destructors look alike. Based on a patch
by Jaakko Heinonen.
Submitted by: Jaakko Heinonen
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
When trying to read scratched or damaged CDs and DVDs, the default
mechanism is sub-optimal. Programs like ddrescue do much better if
you turn off retries entirely, since their algorithms are designed
scan big areas fast, then winnow the areas down. Turning off retries
speeds these programs up by as much as 20x, since the drive is able to
'stream past' many small errors...
The sysctl/tunable kern.cam.cd.retry_count controls this. That
defaults to '4' (for a total of 5 attempts). Setting to 0 turns off
all retry attempts.
Reviewed by: scottl@
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
because the media was removed, the periph would get its refcount dropped
and ultimately freed before getting unlocked. This created a dangling
pointer that was easy to trip over. This fixes a common source of
crashes with removaable media, but problems remain and will get tracked
down.
http://www.t10.org/lists/1spc-lst.htm
Note opcodes for scanner and communication devices are taken from the previous
revision because they are not listed in the files any more.
Also, note newly added ASCs are all marked with 'XXX TBD' and take SS_RDEF action
for now. Some ASCs need SS_TUR for error recovery or SS_FATAL to prevent further
retrials. We should deal with them later.
Reviewed by: scottl, ken
the referenced data is only obtained/changed in the device open handler,
and the ioctl handler can only run after the open handler. Also fix a
few nearby style issues.
Submitted by: Matt Jacob
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
flash card reader.
Also remove an 'Opened da0 -> <random number>' which is not needed on a daily
basis (available through bootverbose).
Reviewed by: phk, ken
MFC after: 1 week
the ORDERED tag. This recoups significant performance gains for many
arrays.
The default is still to send out the ORDERED tag periodically.
Reviewed by: scsi (justin+timeout)
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
REPORT LUNS command to a device.
camcontrol.[c8]: Implement reportluns. This tries to print the LUNs
out in a reasonable format. Only the periph
addressing method has been tested, since very little
hardware that I know of supports the other methods.
scsi_all.[ch]: Revamp the report luns CDB structure and helper
functions. This constitutes a little bit of an API
change, but since the old CDB length was 10 bytes,
and the REPORT LUNS CDB length is actually 12 bytes,
it's clear that no one was using this API in the
first place.
MFC After: 1 week
usage as of SPC2r20. Specifically, handle the BQueue
flag which will indicate that a device supports the
Basic Queueing model (no Head of Queue or Ordered tags).
When this flag is set, SID_CmdQueue is clear. This has
causes FreeBSD to assume that the device did not support
tagged operations.
MFC after: 1 month
This version of scsi_target.c removes all SMP locking until
we have a lock-aware CAM stack. This allows us to use KNOTE
without a panic at least.
It's not yet clear whether target mode is working yet or not.
Discussed with: Scott, Ken, Nate, Justin
return to user space w/o waiting for I/O to complete.
I tried to get several folks who know this code better than me to review it
with no luck. I *do* know that w/o this code, using the SCSI target driver
panics in userret (if it doesn't panic in knote first).
an application to upon a tape (yea, even the non-control device) even if
it cannot establish a mount session. If the open cannot establish a mount
session and O_NONBLOCK was specified, the tape becomes 'open pending mount'.
All I/O operations that would require access to a tape thereafter until
a close attempt to initiate the mount session. If the mount session succeeds,
the tape driver transitions to full open state, else returns an appropriate
I/O error (ENXIO).
At the same time, add a change that remembers whether tape is being opened
read-only. If so, disallow 'write' operations like writing filemarks that
bypass the normal read-only filtering operations that happen in the write(2)
syscall.
Reviewed by: ken, justin, grog
MFC after: 2 weeks
Suggested by: The Bacula Team
the underlying drive had been hot-unplugged from the system. Here
is a specific example. Filesystem code had opened /dev/da1s1e.
Subsequently, the drive was hot-unplugged. This (correctly) caused
all of the associated /dev/da1* entries to be deleted. When the
filesystem later realized that the drive was gone it closed the
device, reducing the write-access counts to 0 on the geom providers
for da1s1e, da1s1, and da1. This caused geom to re-taste the
providers, resulting in the devices being created again. When the
drive was hot-plugged back in, it resulted in duplicate /dev entries
for da1s1e, da1s1, and da1.
This fix adds a new disk_gone() function which is called by CAM when a
drive goes away. It orphans all of the providers associated with the
drive, setting an error condition of ENXIO in each one. In addition,
we prevent a re-taste on last close for writing if an error condition
has been set in the provider.
Sponsored by: Isilon Systems
Reviewed by: phk
MFC after: 1 week
event handler, dev_clone, which accepts a credential argument.
Implementors of the event can ignore it if they're not interested,
and most do. This avoids having multiple event handler types and
fall-back/precedence logic in devfs.
This changes the kernel API for /dev cloning, and may affect third
party packages containg cloning kernel modules.
Requested by: phk
MFC after: 3 days
- Introducing the possibility of using locks different than mutexes
for the knlist locking. In order to do this, we add three arguments to
knlist_init() to specify the functions to use to lock, unlock and
check if the lock is owned. If these arguments are NULL, we assume
mtx_lock, mtx_unlock and mtx_owned, respectively.
- Using the vnode lock for the knlist locking, when doing kqueue operations
on a vnode. This way, we don't have to lock the vnode while holding a
mutex, in filt_vfsread.
Reviewed by: jmg
Approved by: re (scottl), scottl (mentor override)
Pointyhat to: ssouhlal
Will be happy: everyone
module-specific malloc types. These should help us to pinpoint the
possible memory leakage in the future.
- Implementing xpt_alloc_ccb_nowait() and replacing all malloc/free based
CCB memory management with xpt_alloc_ccb[_nowait]/xpt_free_ccb. Hopefully
this would be helpful if someday we move the CCB allocator to use UMA
instead of malloc().
Encouraged by: jeffr, rwatson
Reviewed by: gibbs, scottl
Approved by: re (scottl)
