loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
This is not only a prudent thing to do, but also makes sure that probe
method is not confused by non-NULL 'private', if the previous attach
attempt fails for any reason.
PR: kern/142561
Tested by: Alex Goncharov <alex-goncharov@comcast.net>
MFC after: 4 days
chains. This part of code is to enhance performance so failing the
collapsing should not free TX frames. Otherwise bge(4) will
unnecessarily drop frames which in turn can freeze the network
connection.
Reported by: Igor Sysoev (is <> rambler-co dot ru)
Tested by: Igor Sysoev (is <> rambler-co dot ru)
copper and fiber interfaces over GMII so an explicit check is
necessary to know whether it was configured for fiber interface.
This change make BCM5715S work.
Tested by: olli
MFC after: 1 week
over GMII, make sure to enable GMII. With this change brgphy(4) is
used to handle the dual mode PHY. Since we still don't have a sane
way to pass PHY specific information to mii(4) layer special
handling is needed in brgphy(4) to determine which mode of PHY was
configured in parent interface.
This change make BCM5715S work.
Tested by: olli
Obtained from: OpenBSD
MFC after: 1 week
o Don't enable BGE_FLAG_BER_BUG on both 5722 and 5756, and based
on their PCI IDs rather than their chip IDs.
Reported by: several PC-BSD users via kmoore
Reviewed by: yongari, imp, jhb, davidch
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_READ(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
MFC after: 1 month
now due to unidentified synchonization problem. For 7.1 soundcards 5.1
support handled correctly via software upmix done by sound(4).
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
Pertinant highlights from Myricom CHANGES file include:
- Make sure invalid external smbus activity cannot affect performance
- Fix to avoid a bug where the link could sometimes stay reported as
up on after unplugging the cable.
- For 8B NIC, make smbus connection passive at init to avoid
possible address conflicts
- Increase number of slices to 17 for multi-slice fw
- Fix a bug where packets dropped because of link_overflow could
be occasionally reported as bad_crc32
- Add selectable failover strategy for dual-port chip: symmetric or primary/backup
- On failover, send RARP broadcast to make the change immediately
known to the network
- Change endianess for PCI Device Serial Number
- For dual-port NICs, time to failover is now a few microsecs
instead of a few millisecs.
MFC after: 3 days
I/O port access is implemented on Itanium by reading and writing to a
special region in memory. To hide details and avoid misaligned memory
accesses, a process did I/O port reads and writes by making a MD system
call. There's one fatal problem with this approach: unprivileged access
was not being prevented. /dev/io serves that purpose on amd64/i386, so
employ it on ia64 as well. Use an ioctl for doing the actual I/O and
remove the sysarch(2) interface.
Backward compatibility is not being considered. The sysarch(2) approach
was added to support X11, but support for FreeBSD/ia64 was never fully
implemented in X11. Thus, nothing gets broken that didn't need more work
to begin with.
MFC after: 1 week
register, nVidia chipsets have different oppinion, requiring every interrupt
to be acknowledged there.
While there, add interrupt descriptions in multi-vector MSI mode.
Pass the channel argument as a real argument and not through
RXON. The RXON version seems to have problem with both the older
228.57.2.23 firmware and the latest 228.61.2.24 version resulting
in device initialization errors like:
wpa_supplicant[2928]: Failed to initiate AP scan.
kernel: firmware error log:
kernel: error type = "SYSASSERT" (0x00000005)
kernel: program counter = 0x0000147C
kernel: source line = 0x0000058B
kernel: error data = 0x0000058B00000000
kernel: branch link = 0x0000145A00001492
kernel: interrupt link = 0x000006DE00000000
kernel: time = 7310
...
kernel: iwn0: iwn_config: could not set TX power
kernel: iwn0: iwn_init_locked: could not configure device, error 35
By passing the current channel to hal->set_txpower() the firmware
error is fixed, at least for the 4965 chipset of my Thinkpad and
the ones tested by Bernhard.
Submitted by: Bernhard Schmidt <bschmidt@techwires.net>
Approved by: rpaulo
