Include source files and drivers for Marvell ArmadaXP and Armada38X
in GENERIC kernel config.
Submitted by: Michal Mazur <mkm@semihalf.com>
Rafal Kozik <rk@semihalf.com>
Reviewed by: manu
Tested by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
DTB Overlays are useful to change/add nodes to a dtb without the need to
modify it.
Add support for building dtbo during buildkernel.
The goal of DTBO present in the FreeBSD source tree is to fill a gap in
time when we submit changes upstream (Linux). Instead of waiting 2 to 4 months
we can add a DTBO in tree in the meantime.
This is not for adding DTBO for capes/hat/addon boards, those will be
better to put in a ports.
This is also not for enabling a i2c/spi/pwm controller on certain pins,
each user have a different use case for those (which pins to use etc ...)
and we cannot have all possible configuration.
Add a dtbo for sun8i-h3-sid which add the SID node missing in upstream dts.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D14782
The emac bindings that are landing in Linux 4.15 specify a syscon property
on the emac node that point to /soc/syscon. Use this property if it's
specified, but maintain backwards compatibility with the old method.
The older method is still used for boards that we get .dtb from u-boot, such
as pine64, that did not yet have stable emac bindings.
Tested on: Banana Pi-M3 (a83t)
Tested on: Pine64 (a64)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13296
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
With that gone they need to go into GENERIC now.
Makes FreeBSD/arm usable on gem5 by default.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D12566
Transition all boards that support arm cortex CPUs to armv7. This
leaves two armv6 kernels in the tree. RPI-B, which uses the BCM2835
which has a ARM1176 core, and VERSATILEPB, which is a qemu board setup
around the time RPI-B went in. Copy std.armv6 to std.armv7, even
though that duplicates a lot of stuff. More work needs to be done to
sort out the duplication.
Differential Revision: https://reviews.freebsd.org/D12027
Merge in the missing devices from the IMX6 and ZEDBOARD kernel configs. The
Freescale sdma device has been renamed to fslsdma to mark it as a platform
specific driver.
Reviewed by: ian
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D11564
transfers in their probe() or attach() routines, and that doesn't work
when the low-level controller requires interrupts to be functional.
The DS133x family of chips is nearly identical to the DS1307 and support
for them should be added to that driver, then the ds133x driver can be
deleted. The s35390a driver just needs a non-trivial workover. In both
cases that work will be done and committed separately.
This allows multiple instances of SoCs that use the pl310 driver to be
built within the same kernel:
* Add access to the platform_t object from outside platform.c
* Use this with the pl310 driver
There is a new platform_pl310 interface to replace the existing code. SoCs
need to implement the init method, and if they have special requirements to
write to the two registers we care about will also need to implement the
write_ctrl and write_debug methods.
Differential Revision: https://reviews.freebsd.org/D11546
H2+ SoC is a stripped down version of H3 without gigabit ethernet and 4K HDMI.
Also add sun8i-h2-plus-orangepi-zero.dts to the build as we run on this board.
cfumass(4) is not usable if usfs(4) is loaded or compiled into the
kernel. Remove usfs so that the user may kldload the USB mass storage
target they prefer.
PR: 218169
Reviewed by: trasz, hselasky (no objection)
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10153
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
While here:
- remove 'device mii' - included by miibus;
- remove 'device smcphy' - included by miibus;
- sorted the network drivers list;
- added a comment about miibus based on amd64/GENERIC.
Sponsored by: Rubicon Communications, LLC (Netgate)
Push-Pull Two Wire interface is a almost compatible iic like bus used
in sun6i SoC. It's only use is to communicate with the power management IC.
Reviewed by: jmcneill
MFC after: 1 week
Relnotes: yes
for later Cortex-A CPUs that support the Multiprocessor Extensions. This
will be needed to support both in a single GENERIC kernel while still
being able to only build for a single SoC.
Reviewed by: mmel
Relnotes: yes
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8138
SMP SoCs and qemu virt. Further SoCs can be supported if they support the
PLATFORM, PLATFORM_SMP, and MULTIDELAY options.
Tested by: manu
Sponsored by: ABT Systems Ltd
