to pull vm_param.h was removed. Other big dependency of vm_page.h on
vm_param.h are PA_LOCK* definitions, which are only needed for
in-kernel code, because modules use KBI-safe functions to lock the
pages.
Stop including vm_param.h into vm_page.h. Include vm_param.h
explicitely for the kernel code which needs it.
Suggested and reviewed by: alc
MFC after: 2 weeks
Don't use Maxmem when the amount of memory is meant. Use realmem instead.
Maxmem is not only a MD variable, it represents the highest physical memory
address in use. On systems where memory is sparsely layed-out the highest
memory address and the amount of memory are not interchangeable. Scaling the
AGP aperture based on the actual amount of memory (= realmem) rather than
the available memory (= physmem) makes sure there's consistent behaviour
across architectures.
agp_i810.c:
While arguably the use of Maxmem can be considered correct, replace its use
with realmem anyway. agp_i810.c is specific to amd64, i386 & pc98, which
have a dense physical memory layout. Avoiding Maxmem here is done with an
eye on copy-n-paste behaviour in general and to avoid confusion caused by
using realmem in agp.c and Maxmem in agp_i810.c.
In both cases, remove the inclusion of md_var.h
operations required by GEMified i915.ko. It also attaches to SandyBridge
and IvyBridge CPU northbridges now.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
scope of the object lock in agp_i810.c. (In this specific case, the scope
of the object lock shouldn't matter, but I don't want to create a bad
example that might be copied to a case where it did matter.)
Reviewed by: kib
Note that you need at least xf86-video-intel 2.4.3 for this to work.
The G4X doesn't put the GATT into the same area of stolen memory
as all the other chips and older versions of the driver didn't
handle that properly.
Tested by: ganbold
Approved by: kib
MFC after: 2 weeks
g33 based chips use a different method of identifying the gtt size.
g45 based chips gtt is located in a different area of stolen memory.
Approved by: jhb (mentor)
MFC after: 2 weeks
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
/dev/agpgart and agp_free_res() frees resources like the BAR for the
aperture. Splitting this up lets chipset-specific detach routines
manipulate the aperture during their detach routines without panicing.
MFC after: 1 week
Reviewed by: anholt
This adds a function to agp.c to set the aperture resource ID if it's
not the usual AGP_APBASE. Previously, agp.c had been assuming
AGP_APBASE, which resulted in incorrect agp_info, and contortions by
agp_i810.c to work around it.
This also adds functions to agp.c for default AGP_GET_APERTURE() and
AGP_SET_APERTURE(), which return the aperture resource size and disallow
aperture size changes. Moving to these for our AGP drivers will likely
result in stability improvements. This should fix 855-class aperture
size detection.
Additionally, refuse to attach agp_i810 when some RAM is above 4GB and
the GART can't reference memory that high. This should be very rare.
The correct solution would be bus_dma conversion for agp, which is
beyond the scope of this change. Other AGP drivers could likely use
this change as well.
G33/Q35/Q33 AGP support is also included, but disconnected by default
due to lack of testing.
PR: kern/109724 (855 aperture issue)
Submitted by: FUJIMOTO Kou<fujimoto@j.dendai.ac.jp>
Approved by: re (hrs)
The key problem was that the aperture size detection using the MSAC bit
doesn't work -- the bit appears to be set even when it shouldn't be. Linux
takes a different approach, testing for a bit of the GMADR (PCIR_BAR(2)) being
set. However, as I don't think that's a safe way to test aperture size, we
just allocate the resource and check its size. This also pointed out that
agp_generic_attach hadn't been allocating our aperture resource, which may
have caused problems in some cases.
Also corrected is a minor copy-and-pasteo in an error case.
PR: kern/103079
Submitted by: mnag
Tested on: i945GM, i915GM
MFC after: 2 weeks
capability is present as not all devices supported by the agp_i810 driver
(such as i915) have the AGP capability. Instead, add an identify routine
to the agp_i810 driver that uses the PCI ID to determine if it should
create an agp child device.
the addition of pci_find_extcap().
- Change the drm drivers to attach to vgapci. This is #ifdef'd so the
code can be shared across branches.
- Use pci_find_extcap() to look for AGP and PCIE capabilities in drm.
- GC all the drmsub stuff for i810/i830/i915. The agp and drm devices are
now both children of vgapci.
and some fixes from Motomichi Matsuzaki. Testing involved many people, but the
final, successful testing was from rwatson who endured several rounds of "it
crashes at XYZ stage" "oh, please correct this typo and try again." The Linux
driver, and to a small extent the limited specs, were both used as a reference
for how to program the chipset.
PR: kern/80396
Submitted by: Martin Mersberger
caller to vm_page_grab(). Although this gives VM_ALLOC_ZERO a
different meaning for vm_page_grab() than for vm_page_alloc(), I feel
such change is necessary to accomplish other goals. Specifically, I
want to make the PG_ZERO flag immutable between the time it is
allocated by vm_page_alloc() and freed by vm_page_free() or
vm_page_free_zero() to avoid locking overheads. Once we gave up on
the ability to automatically recognize a zeroed page upon entry to
vm_page_free(), the ability to mutate the PG_ZERO flag became useless.
Instead, I would like to say that "Once a page becomes valid, its
PG_ZERO flag must be ignored."
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
